BS A 337-1999 Nuts anchor self-locking floating single lug with counterbore with MJ threads classifications 1100 MPa (at ambient temperature) 235 C 1100 MPa (at ambient temperature.pdf

1、BRITISH STANDARD AEROSPACE SERIES BSA337:1999 ISO3224:1998 Nuts, anchor, self-locking, floating, single lug, with counterbore, with MJthreads, classifications: 1100MPa (at ambient temperature)/235 C, 1100MPa (at ambient temperature)/315 C and1100MPa (atambient temperature)/425 C Dimensions ICS 49.03

2、0.30BSA337:1999 This British Standard, having been prepared under the directionof the Engineering SectorCommittee, was publishedunder the authority ofthe Standards Committee andcomes into effect on 15 February1999 BSI 05-1999 ISBN 0 580 32171 1 National foreword This British Standard reproduces verb

3、atim ISO3224:1998 and implements it as the UK national standard. The UK participation in its preparation was entrusted by Technical Committee ACE/12, Aerospace fasteners and fastening systems, to Subcommittee ACE/12/1, Aerospace fasteners and fastening systems (International), which has the responsi

4、bility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UKinterests informed; monitor related international and European developments and promulgate them in the UK. A list

5、of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “Internatio

6、nal Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a Briti

7、sh Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theISO title page, pageii, pages1 to3 and a back cover. This standard has been updated (see copyright date) and may have had amendment

8、s incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSA337:1999 BSI 05-1999 i Contents Page National foreword Inside front cover Foreword ii Introduction 1 1 Scope 1 2 Normative references 1 3 Configuratio

9、n and dimensions 1 Figure 1 2 Table 1 3ii blankBSA337:1999 ii BSI05-1999 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO tec

10、hnical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison withISO, also take part in the work. ISO collaborates closely

11、 with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part3. Draft International Standards adopted by the technical committees are circulated to t

12、he member bodies for voting. Publication as an International Standard requires approval by at least75% of the member bodies casting a vote. International Standard ISO3224 was prepared by Technical Committee ISO/TC20, Aircraft and space vehicles, Subcommittee SC4, Aerospace fastener systems. This sec

13、ond edition cancels and replaces the first edition (ISO3224:1985), which has been technically revised. Descriptors: Aircraft industry, fasteners, MJ threads, nuts (fasteners), anchor nuts, self-locking nuts, single-lug nuts, floating nuts, counterbore nuts, classification, form specifications, dimen

14、sions.BSA337:1999 BSI 05-1999 1 Introduction The dimensions specified in this International Standard have been determined to allow production of a part which will satisfy the requirements of the procurement specification ISO5858. 1 Scope This International Standard specifies the dimensions of self-l

15、ocking, floating, single lug anchor nuts, with counterbore, with MJ threads, of classifications:1100MPa 1) /235 C 2) , 1100MPa 1) /315 C 2)and1100MPa 1) /425 C 2) . This International Standard is only applicable for the compilation of aerospace product standards. 2 Normative references The following

16、 normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Sta

17、ndard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International St

18、andards. ISO5855-2:1988, Aerospace MJ threads Part2:Limit dimensions for bolts and nuts. ISO5858:1991, Aerospace Self-locking nuts with maximum operating temperature less than or equal to425 C Procurement specification. ISO8788:1987, Aerospace Fasteners Tolerances of form and position for nuts. 3 Co

19、nfiguration and dimensions See Figure 1 and Table 1. Dimensions and tolerances are expressed in millimetres. They apply after any surface coating(s) but before the application of any lubricant. The metallic cap (optional) shall remain joined to the nut at the maximum operating temperature (type of a

20、ttachment at the users discretion). SeeISO5858 for the test conditions. 1) Corresponds to the minimum tensile stress which the nut is able to withstand at ambient temperature without breaking or cracking when tested with a bolt of a higher strength class. 2) Maximum temperature that the nut is able

21、to withstand, without permanent alteration to its original characteristics, after ambient temperature has been restored. The maximum temperature is conditioned by the surface treatment.BSA337:1999 2 BSI 05-1999 Figure 1 BSA337:1999 BSI 05-1999 3 Table 1 Diameter code Thread a C max. D max. E F G min

22、. H min. j b max. K max. L max. M max. N max. P c max. Q max. R max. S T max. V 0.25 W min. Radial float Z min. 030 MJ3 0,5-4H6H 8,5 8 4,6 11 26,5 4 0,9 3,5 2,5 4,5 4,8 4,5 0,5 040 MJ4 0,7-4H6H 0,4 6,6 4,4 2,2 6,2 5,8 11 13 5,5 050 MJ5 0,8-4H6H 8,1 9,5 5,5 2,4 7,3 12 27,5 6,9 11,4 13,4 6,5 0,7 060 M

23、J6 1-4H5H 9,2 11 6,5 2,7 8,7 13,5 30 8,1 12,7 14,7 4 4,6 7,5 080 MJ8 1-4H5H 0,5 12,8 8,5 8,5 10,9 16 32,7 9,9 1,1 15 18 3 5,5 5,7 9,5 0,75 100 MJ10 1,25-4H5H 15 13 10,5 3 12,9 18 36,7 12 20,2 22 5 3,5 6 6,6 11,5 a In accordance with ISO5855-2. In the self-locking zone, the tolerances apply before fo

24、rming out-of-round. b Measured at sharp corners (chamfered) or point of tangency (radiused) c Maximum protrusion of the boltBSA337:1999 ISO3224:1998 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards

25、. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant ai

26、m of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:020899

27、69000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services.

28、 Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, Eu

29、ropean and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing member

30、s of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also h

31、olds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, record

32、ing or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.