BS AU 216-1-1987 Hydraulic brake systems using petroleum base brake fluids for road vehicles - Specification for petroleum base reference fluid《道路车辆用石油基制动液的液压制动系统 第1部分 石油基基准液规范》.pdf

1、BRITISH STANDARD AUTOMOBILE SERIES BS AU216-1: 1987 ISO7309:1985 Hydraulic brake systems using petroleum base brake fluids for road vehicles Part 1: Specification for petroleum base reference fluid ISO title: Road vehiclesHydraulic braking systems ISOreference petroleum base fluid UDC629.113-592.2:6

2、65.767:621.22BSAU216-1:1987 This BritishStandard, having been prepared under the directionof the Rubber StandardsCommittee, was published under the authority ofthe Board of BSI and comes intoeffect on 31July1987 BSI02-2000 The following BSI references relate to the work on this standard: Committee r

3、eference RUM/40 Draft (ref.83/36744) announced inBSI News August1983 ISBN 0 580 15968 X Committees responsible for this BritishStandard The preparation of this BritishStandard was entrusted by the Rubber Standards Committee (RUM/-) to Technical Committee RUM/40, upon which the following bodies were

4、represented: British Chemical Distributors and Traders Association Limited British Rubber Manufacturers Association Chemical Industries Association Department of Transport (Highways) Institute of Petroleum London Regional Transport Malaysian Rubber Producers Research Association Ministry of Defence

5、Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No. Date of issue CommentsBSAU216-1:1987 BSI 02-2000 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope and field of application 1 2 References 1 3 Composition 1 4 Physical

6、 and chemical characteristics required 1 Table 1 1 Table 2 1 Publications referred to Inside back coverBSAU216-1:1987 ii BSI 02-2000 National foreword This Part of this BritishStandard has been prepared under the direction of the Rubber Standards Committee in consultation with the Automobile Standar

7、ds Committee. It is identical with ISO7309:1985 “Road vehiclesHydraulic braking systemsISO reference petroleum base fluid”, published by the International Organization for Standardization (ISO). This is Part1 of BS AU216 which covers components for vehicle braking systems using petroleum base fluids

8、. It is intended to issue other Parts specifying petroleum base brake fluid, boots, cups and seals for use in the braking system. The associated BritishStandard BS AU174 “Hydraulic brake systems, using non-petroleum base brake fluids, for road vehicles” specifies similar components for vehicle braki

9、ng systems using non-petroleum base fluids. Terminology and conventions. The text of the International Standard has been approved as suitable for publication as a BritishStandard without deviation. Some terminology and certain conventions are not identical with those used in BritishStandards; attent

10、ion is drawn especially to the following. The comma has been used as a decimal marker. In BritishStandards it is current practice to use a full point on the baseline as the decimal marker. Wherever the words “International Standard” appear, referring to this standard, they should be read as “Part of

11、 this BritishStandard”. The Technical Committee has reviewed the provisions of ISO3104, ISO3405 and ISO6618, to which reference is made in the text and has decided that they are acceptable for use in conjunction with this standard. ISO3104:1976 and ISO3405:1975 are related to BS2000 “Methods of test

12、 for petroleum and its products” Part71:1982 “Kinematic viscosity of transparent and opaque liquids and calculation of dynamic viscosity” and Part123:1985 “Distillation of petroleum products”, respectively. A British Standard does not purport to include all the necessary provisions of a contract. Us

13、ers of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references International Standard Corresponding BritishStandard ISO2592:1973 BS4689:1980 Method for determination of flash and f

14、ire points of petroleum products: Cleveland open cup method (Identical) ISO3016:1974 BS2000 Methods of test for petroleum and its products Part15:1982 Pour point of petroleum oils (Technically equivalent) Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pa

15、ges1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BSAU216-1:1987 BSI 02-2000 1 1 Scope and field of application This International St

16、andard specifies the composition and required characteristics of a reference fluid 1)used for the testing of hydraulic braking systems and components mounted on road vehicles. 2 References ISO2592, Petroleum productsDetermination of flash and fire pointsCleveland open cup method. ISO3016, Petroleum

17、oilsDetermination of pour point. ISO3104, Petroleum productsTransparent and opaque liquidsDetermination of kinematic viscosity and calculation of dynamic viscosity. ISO3405, Petroleum productsDetermination of distillation characteristics. ISO6618, Petroleum products and lubricants Neutralization num

18、berColour indicator titration method 2) . 3 Composition The composition of the ISO reference petroleum base fluid 1)is given in Table 1. Table 1 4 Physical and chemical characteristics required The required characteristics of the ISO reference petroleum base fluid are given in Table 2. Table 2 1) A

19、list of suppliers of the reference fluid or its constituents is available from the ISO/TC22 Secretariat or the ISO Central Secretariat. 2) At present at the stage of draft. Item Constituent Composition %(m/m) 1 2 3 4 5 6 Pentamers of hydrogenated propylene Poly(alkyl methacrylate) 1,4-di (t-butyloxy

20、) benzene Tri(isopropylphenyl) phosphate Anthraquinone green colouring Perylene yellow-green colouring 80 1,2 17 1 0,5 0,05 1 0,1 (20 2) 10 4 (40 4) 10 4 Characteristic Unit Method of determination Value Kinematic viscosity at100 C Kinematic viscosity at40 C Kinematic viscosity at40 C Pour point Fla

21、sh point (Cleveland open cup) Initial boiling point Neutralization number I A Phosphorus mm 2 /s mm 2 /s mm 2 /s C C C mg KOH/g ppm ISO3104 ISO3104 ISO3104 ISO3016 ISO2592 ISO3405 ISO6618 a X-ray fluorescence W 6 18u vu 21 u 2 000 50 W 105 W 240 u 0,2 800 80 a A potentiometric method will form the s

22、ubject of ISO6619.2 blankBSAU216-1:1987 BSI 02-2000 Publications referred to Seenational foreword.BS AU216-1: 1987 ISO7309:1985 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK

23、view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve t

24、he quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:0208996740

25、0. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax

26、:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and internatio

27、nal standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up

28、to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, i

29、n the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise with

30、out prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.