BS AU 225-1988 Specification for dimensions of steering ball joints for commercial road vehicles《商用道路车辆转向球形接合件尺寸规范》.pdf

1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 225:1988 ISO7803:1987 Specification for Dimensions of steering ball joints for commercial road vehicles ISO title: Commercial road vehicles Steering ball joints UDC 629.114.4:629.11.014.5:629.11.011.72:(083.3)BSAU225:1988 This BritishStandard, having been pre

2、pared under the directionof the Automobile Standards Committee, was published under the authority ofthe Board of BSI and comesintoeffect on 31August1988 BSI02-2000 The following BSI references relate to the work on this standard: Committee reference AUE/13 Draft for comment82/73029 DC ISBN 0 580 167

3、30 5 Committees responsible for this British Standard The preparation of this BritishStandard was entrusted by the Automobile Standards Committee (AUE/-) to Technical Committee AUE/13, upon which the following bodies were represented: Department of Transport (Highways) Freight Transport Association

4、Institute of Road Transport Engineers (Incorporated) London Regional Transport Ministry of Defence National Bus Company Road Haulage Association Ltd. Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No. Date of issue CommentsBSAU225:1988 BSI 02-2000 i Conte

5、nts Page Committees responsible Inside front cover National foreword ii 1 Scope and field of application 1 2 Dimensions 1 3 Designation 1BSAU225:1988 ii BSI 02-2000 National foreword This BritishStandard has been prepared under the direction of the Automobile Standards Committee and is identical wit

6、h ISO7803:1987 “Commercial road vehicles Steering ball joints”, published by the International Organization for Standardization (ISO). Terminology and conventions. The text of the International Standard has been approved as suitable for publication as a BritishStandard without deviation. Some termin

7、ology and certain conventions are not identical with those used in BritishStandards; attention is drawn especially to the following. The comma has been used as a decimal marker. In BritishStandards it is current practice to use a full point on the baseline as the decimal marker. Wherever the words “

8、International Standard” or “ISO7803” appear, referring to this standard, they should be read as “BritishStandard” and “BS AU225” respectively. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct appli

9、cation. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, page1 and a back cover. This standard has been updated (see copyright date) and may have had amendments i

10、ncorporated. This will be indicated in the amendment table on the inside front cover.BSAU225:1988 BSI 02-2000 1 1 Scope and field of application This International Standard specifies the main dimensions of steering ball joints for commercial vehicles. The ball joint is considered as being a single p

11、iece with its socket. Thus this International Standard covers the ball-socket assembly. 2 Dimensions For dimensions, see the figure and table. 3 Designation Example for the designation of a ball joint of nominal size S 8 D=30mm, where the angles =40 and=20 : Ball joint ISO78033040 20 Dimensions in m

12、illimetres Nominal size S8 D A max. B C max. D 1 1) h9 a D 2 max. D 3 2) G 2 H min. L h11 r max. 3) min. 3) min. 27 66 24 3 20 50 M24 1,5 95 60 24 32 30 71 26 3 22 58 M28 1,5 105 65 26 37 35 81 30 3 26 67 M30 1,5 115 75 30 42 40 20 40 91 34 3 30 74 M30 1,5 120 80 34 47 50 109 40 3 38 85 M38 1,5 135

13、85 42 54 a Bore H8. 1) To ensure satisfactory operation of the taper drive, it is necessary for the manufacturers to provide such tolerances that the contact between the male and female cones starts from the major diameter and extends to at least60% of the contact area. 2) The stud D 3is available w

14、ith either right-hand thread or left-hand thread. For ball joints with left-hand thread, the designation should be supplemented by the letters LH. 3) The vehicle manufacturer on consultation with the ball joint manufacturer may specify different angles.BS AU 225:1988 ISO7803:1987 BSI 389 Chiswick Hi

15、gh Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendmen

16、t or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would i

17、nform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standa

18、rds. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been publishe

19、d as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which

20、 give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits c

21、ontact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no

22、 extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such a

23、s symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.