BS DD IEC TS 61994-1-2007 Piezoelectric and dielectric devices for frequency control and selection Glossary Piezoelectric and dielectric resonators《频率控制和选择用压力器件和介质器件 压电介质谐振器》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationPiezoelectric and dielectricdevices for frequencycontrol and selection Glossary Part 1: Piezoelectric anddielectric resonatorsDD IEC/TS 61994-1:2007National forewordThis Draft fo

2、r Development is the UK implementation of IEC/TS 61994-1:2007. It supersedes DD IEC/TS 61994-1:2003, which is withdrawn.This publication is not to be regarded as a British Standard.It is being issued in the Draft for Development series of publications and is of a provisional nature. It should be app

3、lied on this provisional basis, so that information and experience of its practical application can be obtained.Comments arising from the use of this Draft for Development are requested so that UK experience can be reported to the international organization responsible for its conversion to an inter

4、national standard. A review of this publication will be initiated not later than three years after its publication by the international organization so that a decision can be taken on its status. Notification of the start of the review period will be made in an announcement in the appropriate issue

5、of Update Standards.According to the replies received by the end of the review period, BSI Committee GEL/107 will decide whether to support the conversion into an international Standard, to extend the life of the Technical Specification or to withdraw it. Comments should be sent to the Secretary of

6、BSI Technical Committee GEL/107 at British Standards House, 389 Chiswick High Road, London W4 4AL.The UK participation in its preparation was entrusted to Technical Committee GEL/107, Process management for avionics.A list of organizations represented on this committee can be obtained on request to

7、its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2007ISBN 978 0 580 56333 1ICS 01.040.31, 31.140Compliance with a British Standard cannot confer immunity from legal obligations.This Draft for

8、 Development was published under the authority of the Standards Policy and Strategy Committee on 30 November2007.Amendments issued since publicationAmd. No. Date Text affectedDRAFT FOR DEVELOPMENTDD IEC/TS 61994-1:2007IEC/TS 61994-1Edition 2.0 2007-08TECHNICAL SPECIFICATIONPiezoelectric and dielectr

9、ic devices for frequency control and selection Glossary Part 1: Piezoelectric and dielectric resonators IEC/TS61994-1:2007(E)THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced

10、or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining a

11、dditional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commissio

12、n (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest

13、 edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced

14、 publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electroni

15、c and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedbac

16、k on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC/TS 61994-1Edition 2.0 2007-08TECHNICAL SPECIFICATIONPiezoelectric and dielectric devices for frequency control and selection

17、 Glossary Part 1: Piezoelectric and dielectric resonators INTERNATIONAL ELECTROTECHNICAL COMMISSION SICS 31.140; 01.040.31 PRICE CODEISBN 2-8318-9298-8 2 TS 61994-1 IEC:2007(E) CONTENTS FOREWORD.3 1 Scope.5 2 Normative references .5 3 Terms and definitions .5 Figure 1 Configuration of a dielectric r

18、esonator (TE01mode type) .8 Figure 2 Equivalent circuit of a piezoelectric vibrator (one-port resonator) .9 Figure 3 Frequency characteristics of the impedance near resonance11 Figure 4 Equivalent circuit for a two-port SAW resonator .12 Figure 5 Configuration of an interdigital transducer (IDT) .13

19、 Figure 6 Configuration of a one port SAW resonator 16 Figure 7 Configuration of a two port SAW resonator.21 TS 61994-1 IEC:2007(E) 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ PIEZOELECTRIC AND DIELECTRIC DEVICES FOR FREQUENCY CONTROL AND SELECTION GLOSSARY Part 1: Piezoelectric and dielectric res

20、onators FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardizatio

21、n in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is ent

22、rusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the Inter

23、national Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since

24、each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of

25、 IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in

26、their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment dec

27、lared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC Nation

28、al Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is

29、drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall

30、not be held responsible for identifying any or all such patent rights. The main task of IEC technical committees is to prepare International Standards. In exceptional circumstances, a technical committee may propose the publication of a technical specification when the required support cannot be obt

31、ained for the publication of an International Standard, despite repeated efforts, or the subject is still under technical development or where, for any other reason, there is the future but no immediate possibility of an agreement on an International Standard. IEC 61994-1, which is a technical speci

32、fication, has been prepared by IEC technical committee 49: Piezoelectric and dielectric devices for frequency control and selection. This second edition of IEC 61994-1 cancels and replaces the first edition published in 2003. This edition constitutes a technical revision. The main changes with respe

33、ct to the previous edition are listed below: definitions updated; terminology given in orderly sequence; 4 TS 61994-1 IEC:2007(E) drawings inserted for easier understanding. The text of this technical specification is based on the following documents: Enquiry draft Report on voting 49/761/DTS 49/766

34、/RVC Full information on the voting for the approval of this technical specification can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the IS0/lEC Directives, Part 2. IEC 61994 consists of the following parts under the general tit

35、le: Piezoelectric and dielectric devices for frequency control and selection Glossary: Part 1: Piezoelectric and dielectric resonators Part 2: Piezoelectric and dielectric filters Part 3: Piezoelectric oscillators Part 4-1: Piezoelectric materials Synthetic quartz crystal Part 4-2: Piezoelectric and

36、 dielectric materials Piezoelectric ceramics Part 4-3: Materials for dielectric devices1 Part 4-4: Materials Materials for Surface Acoustic Wave (SAW) devices The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC

37、web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be transformed into an international standard; reconfirmed; withdrawn; replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a late

38、r date. _ 1To be published. TS 61994-1 IEC:2007(E) 5 PIEZOELECTRIC AND DIELECTRIC DEVICES FOR FREQUENCY CONTROL AND SELECTION GLOSSARY Part 1: Piezoelectric and dielectric resonators 1 Scope This technical specification gives the terms and definitions for piezoelectric and dielectric resonators repr

39、esenting the present state-of-the-art, which are intended for use in the standards and documents of IEC technical committee 49. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For

40、undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60050(561):1991, International Electrotechnical Vocabulary (IEV) Chapter 561: Piezoelectric devices for frequency control and selection Amendment 1 (1995) IEC 60122-1:2002, Quarts crystal units

41、of assessed quality Part-1: Generic specification IEC 60642:1979, Piezoelectric ceramic resonators and resonator units for frequency control and selection Chapter I: Standard values and conditions Chapter II: Measuring and test conditions IEC 61019-1:2004, Surface acoustic wave (SAW) resonators Part

42、 1: Generic specification IEC 61338-1:2004, Waveguide type dielectric resonators Part 1: Generic specification 3 Terms and definitions 3.1 adjustment tolerance the maximum permissible deviation of the working frequency of a piezoelectric resonator from the nominal frequency at the reference temperat

43、ure under specified conditions IEV 561-02-16 modified 3.2 ageing tolerance the maximum permissible deviation of the working frequency of a piezoelectric resonator from its initial frequency which is observed with the passage of time under specified conditions IEV 561-02-17 modified 3.3 ageing long-t

44、erm parameter variation relationship which exists between any parameter (for example resonance frequency) and time IEC 61019-1, 4.2.9 3.4 apodisation (spurious suppression for SAW devices) weighting method produced by the change in finger overlap over the length of the IDT to suppress the transverse

45、 spurious modes 6 TS 61994-1 IEC:2007(E) IEV 561-06-18 modified 3.5 anti-resonance frequency af the higher of two frequencies of a piezoelectric resonator vibrating alone, under specified conditions, at which the electrical impedance of the resonator is resistive IEV 561-02-10 3.6 bus bar common ele

46、ctrode region of an IDT which connects individual fingers together and also connects the IDT to an external circuit (see Figure 5) IEV 561-06-15 modified 3.7 capacitance ratio 10CCr = where 0C and 1C represent the shunt capacitance and the motional capacitance respectively in the equivalent circuit

47、(see Figure 2) the capacitance ratio indicates one of the merits of the resonator IEC 61019-1, 4.2.10.9 modified 3.8 centre frequency of a two-port SAW resonator cf arithmetic mean of two frequencies at which the attenuation relative to the minimum insertion attenuation reaches a specified value IEC

48、 61019-1, 4.2.11.9 3.9 clamped capacitance (of a piezoelectric resonator) the capacitance of a piezoelectric resonator measured at a frequency well above any pronounced resonance NOTE In practice, the value of the capacitance is often indirectly determined, because a direct measurement is affected b

49、y the presence of factors such as lead inductance. IEV 561-02-35 3.10 coaxial dielectric resonator dielectric resonator characterized by a TEM mode field distribution with a coaxial waveguide structure of finite length IEC 61338-1, 2.2.19 TS 61994-1 IEC:2007(E) 7 3.11 coplanar resonator dielectric resonator characterised by a TEM mode field distribution. The structure is a coplanar-line wave