BS DD ISO TS 19911-2010 Plastics pipes and fittings - Format of a technical file for characterizing PE spigot end fittings《塑料管线和配件 特征聚乙烯(PE)插口端头配件用技术文件格式》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationDD ISO/TS 19911:2010Plastics pipes and fittings Format of a technical file forcharacterizing PE spigot endfittingsDD ISO/TS 19911:2010 DRAFT FOR DEVELOPMENTNational forewordThis

2、Draft for Development is the UK implementation of ISO/TS19911:2010.This publication is not to be regarded as a British Standard.It is being issued in the Draft for Development series of publicationsand is of a provisional nature. It should be applied on thisprovisional basis, so that information and

3、 experience of its practicalapplication can be obtained.Comments arising from the use of this Draft for Developmentare requested so that UK experience can be reported to theinternational organization responsible for its conversion toan international standard. A review of this publication willbe init

4、iated not later than 3 years after its publication by theinternational organization so that a decision can be taken on itsstatus. Notification of the start of the review period will be made inan announcement in the appropriate issue of Update Standards.According to the replies received by the end of

5、 the review period,the responsible BSI Committee will decide whether to support theconversion into an international Standard, to extend the life of theTechnical Specification or to withdraw it. Comments should be sentto the Secretary of the responsible BSI Technical Committee at BritishStandards Hou

6、se, 389 Chiswick High Road, London W4 4AL.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/88/4, Test Methods - Plastic Piping.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include

7、all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010ISBN 978 0 580 60523 9ICS 23.040.45; 23.040.60Compliance with a British Standard cannot confer immunity fromlegal obligations.This Draft for Development was published under the authority ofthe Standa

8、rds Policy and Strategy Committee on 31 August 2010Amendments issued since publicationDate Text affectedDD ISO/TS 19911:2010Reference numberISO/TS 19911:2010(E)ISO 2010TECHNICAL SPECIFICATION ISO/TS19911First edition2010-06-15Plastics pipes and fittings Format of a technical file for characterizing

9、PE spigot end fittings Tubes et raccords en matires plastiques Modle dune fiche technique caractrisant les raccords bouts mles en polythylne DD ISO/TS 19911:2010ISO/TS 19911:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may

10、 be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accep

11、ts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the

12、 file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be re

13、produced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 2

14、2 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedDD ISO/TS 19911:2010ISO/TS 19911:2010(E) ISO 2010 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of na

15、tional standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Intern

16、ational organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the

17、rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by

18、at least 75 % of the member bodies casting a vote. In other circumstances, particularly when there is an urgent market requirement for such documents, a technical committee may decide to publish other types of document: an ISO Publicly Available Specification (ISO/PAS) represents an agreement betwee

19、n technical experts in an ISO working group and is accepted for publication if it is approved by more than 50 % of the members of the parent committee casting a vote; an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical committee and is accepted for publ

20、ication if it is approved by 2/3 of the members of the committee casting a vote. An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is confir

21、med, it is reviewed again after a further three years, at which time it must either be transformed into an International Standard or be withdrawn. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible f

22、or identifying any or all such patent rights. ISO/TS 19911 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic materials and their accessories Test methods and

23、basic specifications. DD ISO/TS 19911:2010ISO/TS 19911:2010(E) iv ISO 2010 All rights reservedIntroduction The technical file of a spigot end fitting describes the identification of the fitting, the main characteristics of the PE compound and the geometrical characteristics of the fitting, including

24、 the manufacturing tolerances of the product. The technical file can be used to characterize the fitting for type testing and approval by third party certification procedures. Each modification on the fitting is reflected can be a revised technical file. Based on the contents of the revised technica

25、l file, further approval or complementary testing can be considered. DD ISO/TS 19911:2010TECHNICAL SPECIFICATION ISO/TS 19911:2010(E) ISO 2010 All rights reserved 1Plastics pipes and fittings Format of a technical file for characterizing PE spigot end fittings 1 Scope This Technical Specification de

26、scribes the individual elements of a technical file, specifying the characteristics of fittings with spigot ends for butt fusion or electrofusion assembling. All details described in this Technical Specification are provided by the manufacturer of the butt fusion fitting. 2 Normative references The

27、following referenced documents are indispensable for the application of this document. For dated references only the edition cited applies. For undated references the latest edition of the referenced document (including any amendments) applies. ISO 1133, Plastics Determination of the melt mass-flow

28、rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics ISO 12162, Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient ISO 12176-4, Plastics pipes and fittings Equipment for fusion jointing polyethylene systems Part 4:

29、 Traceability coding 3 Description of the spigot end fitting The manufacturers technical file shall include the information, as described in Tables 1 and 2, for the identification of the fitting and the PE compound used. Table 1 Identification of the fitting Name of the manufacturer Trade mark of th

30、e fitting Type of fitting (tee, elbow, reducer, etc.) Application, e.g. water and gas Detailed explanation of the identification coding of the fitting Nominal diameter(s) and SDR Compliance with product standard(s) DD ISO/TS 19911:2010ISO/TS 19911:2010(E) 2 ISO 2010 All rights reservedTable 2 Charac

31、teristics of the PE compound Trade mark Classification of compound in accordance with ISO 12162, e.g. PE100 Compound code in accordance with ISO 12176-4 Melt mass-flow rate, e.g. MFR(190/5) indicating temperature and load used in the test, in accordance with ISO 1133, of the compound and tolerances,

32、 if not provided by the product standard Colour of the compound 4 Geometrical characteristics of the fitting The manufacturers technical file shall provide all relevant dimensions in millimetres. At a minimum, the dimensions related to the symbols shown in Figure 1 and Table 3 shall be provided. The

33、 dimensions used in Table 3 are in conformity with the relevant product standard. The dimensions shown in Figure 1 and Table 3 are the following: D1the mean outside diameter of the fusion end-piece, measured in any plane parallel to the plane of the mouth and at a distance not greater than L2from th

34、at plane; D2the mean outside diameter of the body of the fitting; D3the minimum bore which comprises the minimum diameter of the flow channel through the body of the fitting. This diameter does not include the fusion bead if any; E the thickness of the fitting measured at any point on the wall of th

35、e fitting; Esthe thickness of the fusion-face wall, measured at any point at a maximum distance, L1(cut-back length) from the mouth; L1the length of the cut-back section of the fusion end-piece, which comprises the initial depth of the spigot and which is necessary for butt fusion or electrofusion;

36、L2the tubular length, which comprises the length of the initial, tubular, section of the fusion end-piece; L overall dimensions of the fitting defined by the manufacturer; Ovality out-of-roundness (ovality) of D1measured at any point of L1DD ISO/TS 19911:2010ISO/TS 19911:2010(E) ISO 2010 All rights

37、reserved 3Figure 1 Geometrical characteristics of the spigot end fitting Table 3 Dimensions and tolerances Dimension Unit Nominal Minimum Maximum D1amm D2D3mm E mm Esbmm L1L2mm L mm Ovality (D1)amm aThese values conform to the product standard or specification. bFace thickness reductions due to cham

38、fering of the edge or circumferential reversion when made out of pipe shall be included. The white areas of Table 3 are to be completed. 5 Fusion parameters If required, the manufacturer may provide a butt fusion procedure with the technical file. DD ISO/TS 19911:2010ISO/TS 19911:2010(E) ICS 23.040.

39、45; 23.040.60 Price based on 3 pages ISO 2010 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at

40、 the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-da

41、rds should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical

42、com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996

43、7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20

44、8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national,

45、 Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Sub

46、scribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online acce

47、ss to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under

48、 the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-