BS EN 1083-2-1997 Power-driven brushes - Safety requirements《电刷 第2部分 安全性要求》.pdf

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 1083-2 : 1997 The E

2、uropean Standard EN 1083-2 : 1997 has the status of a British Standard ICS 25.100.70 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Power-driven brushes Part 2. Safety requirementsThis British Standard, having been prepared under the direction of the Consumer Products and Ser

3、vices Sector Board, was published under the authority of the Standards Board and comes into effect on 15 September 1997 BSI 1997 ISBN 0 580 28310 0 BS EN 1083-2 : 1997 Amendments issued since publication Amd. No. Date Text affected National foreword This British Standard is the English language vers

4、ion of EN 1083-2 : 1997. Together with BS EN 1083-1 : 1997, it supersedes BS 6694 : 1986, which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee CW/11, Brushware, which has the responsibility to: aid enquirers to understand the text; present to the responsib

5、le European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secre

6、tary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Ele

7、ctronic Catalogue. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 4, an inside back cover and a back cover.CEN European Committee for Standardiz

8、ation Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref. No. EN 1083-2 : 1997 E EUROPEAN STANDARD EN 1083-2 NOR

9、ME EUROPE ENNE EUROPA ISCHE NORM May 1997 ICS 25.100.70 Descriptors: Brushing machines, brushes, safety, data, tolerances, measurement, marking, labelling English version Power-driven brushes Part 2: Safety requirements Brosses entraine es par un moteur Partie 2: Exigences de se curite Kraftbetriebe

10、ne Bu rstwerkzeuge Teil 2: Sicherheitstechnische Anforderungen This European Standard was approved by CEN on 1997-04-21. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard withou

11、t any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language mad

12、e by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,

13、 Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN 1083-2 : 1997 BSI 1997 Foreword This European Standard has been prepared by the Technical Committee 173, Brushware, the secretariat of which is held by BSI. The definitions for power-driven brushes ar

14、e given in Part 1 of this European Standard. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 1997, and conflicting national standards shall be withdrawn at the latest by November 1997. Ac

15、cording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Swed

16、en, Switzerland and the United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Definitions 3 4 Safety 3 5 Testing 3 6 Marking, labelling and instructions 4Page 3 EN 1083-2 : 1997 BSI 1997 1) Ref. BT C 67/93. 2) The DIN standard is specified as a temporary measure in the absenc

17、e of an equivalent EN. (Resolution BT C 67/93). 1 Scope This Part of EN 1083 specifies safety requirements for power-driven brushes. This standard is not applicable to power-driven brushes made for a specialized application and those designed exclusively for that purpose (such as those defined in 3.

18、10 to 3.21 of EN 1083-1). 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendm

19、ents to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. EN 1083-1 : 1997 Power-driven brushes Part 1: Definitions DIN 69170-2 1) Grindin

20、g points Safety requirements, maximum dimensions, labelling 3 Definitions For the purposes of this European Standard, the definitions given in EN 1083-1 apply. 4 Safety 4.1 Safety factor Rotating brushes shall be made such that they have a safety factor against breakage of the brush body, or looseni

21、ng of parts of the fill material by centrifugal force, of at least 2,25 times the permissible speed. 4.2 Configuration Brush parts shall be designed so that the drive torque is carried from the shaft to the edge of the brush. They shall be shaped in such a manner that a uniform distribution of the f

22、ill material across the brush is ensured. 4.3 Metal shafts Brushes with metal shafts shall have a safety coefficient s against bending of s = 1,3 according to DIN 69170-2 2) . 4.4 Bore diameter Depending on the overall diameter (d 1 ), brushes shall have the minimum bore diameters (d 2 ) specified i

23、n table 1. 4.5 Dimensional limits For the brush bores given in table 1, the dimensional limits in accordance with table 2 shall apply. Table 1. Minimum bore diameters Overall brush diameter (d 1 ) Minimum bore diameter (d 2min ) mm mm 50 4,6 75 6,5 100 10 150 13 200 16 250 20 300 20 350 32 Table 2.

24、Dimensional limits for bore diameters Bore diameter (d 2 ) Dimensional limits mm mm50 to 150 + 0,18 + 0,05 150 to 300 + 0,30 + 0,07 5 Testing Brushes shall be tested under conditions of 2,25-fold safety corresponding to 1,5 times the maximum speed n max . The test duration shall be 10 s at centrifug

25、al force, without load. The test shall be performed three times. After testing, the brush shall not have lost any component parts.Page 4 EN 1083-2 : 1997 BSI 1997 3) Such marking is a claim of compliance with EN 1083-2 but does not imply CEN approval of the product; the accuracy of this claim is the

26、refore solely the responsibility of the person applying the marking. 6 Marking, labelling and instructions 6.1 Marking and labelling A power-driven brush shall be legibly marked with the following: a) the name, registered trademark or other means of identifying the responsible manufacturer or suppli

27、er; b) the number of this European Standard, i.e. EN 1083-2 3) c) the maximum safe speed in revolutions per minute; d) the statement wear eye protection, or a symbol to that effect. NOTE. Additional relevant information may also be provided. Where, for reasons of size or material, it is impracticabl

28、e to mark the brush, this information shall be given on its immediate packaging material. 6.2 Instructions Manufacturers shall provide mounting and safety instructions as follows. a) Brushes should not be mounted on machines having a speed in excess of the maximum permissible brush speed. b) Damaged

29、 brushes should not be used. c) Rust discoloration or other signs of chemical or mechanical changes of the fill material may cause premature failure. d) Brushes should be stored in suitable racks, containers or boxes in such a manner that they are protected against the effects of: 1) high humidity,

30、heat, water or other liquids which might cause damage to the brush; 2) exposure to acids, or fumes from acids, which might induce deterioration; 3) any temperature low enough to cause condensation on the brush when removed from storage to an area of higher temperature; 4) distortion of any of the br

31、ush components.blankBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

32、 | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment

33、or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would i

34、nform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of

35、standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have b

36、een published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also av

37、ailable which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these a

38、nd other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Design

39、s and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of

40、 necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.