BS EN 1087-1-1995 Particle boards - Determination of moisture resistance - Particle boards - Determination of moisture resistance - Boil test《碎料板 耐湿测定 煮沸试验》.pdf

1、BRITISH STANDARD BS EN 1087-1:1995 Particleboards Determination of moisture resistance Part 1: Boil test The European Standard EN 1087-1:1995 has the status of a British StandardBSEN 1087-1:1995 This British Standard, having been prepared under the directionof the Sector Board forBuilding and Civil

2、Engineering, was published underthe authority of the Standards Board and comes intoeffect on 15 June 1995 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference B/541 Draft for comment 93/10436 DC ISBN 0 580 23838 5 Committees responsible for this British S

3、tandard The preparation of this British Standard was entrusted to Technical Committee B/541, Wood-based panels, upon which the following bodies were represented: American Plywood Association Association of British Plywood and Veneer Manufacturers British Woodworking Federation Chartered Institute of

4、 Building Co-ordinator for Timber and Timber Products Council of the Forest Industries of British Columbia Department of the Environment (Building Research Establishement) Finnish Plywood International Flat Roofing Contractors Advisory Board Forestry Commission Furniture Industry Research Associatio

5、n Institution of Structural Engineers Local Authority Organizations Mineral Bonded Board Products Federation National Federation of Roofing Contractors National House-building Council National Panel Products Association Royal Institute of British Architects Structural Board Association Timber Resear

6、ch and Development Association Timber Trade Federation Wood Panel Products Federation Zurich Insurance Company Amendments issued since publication Amd. No. Date CommentsBSEN 1087-1:1995 BSI 09-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 1

7、087-1 3 List of references Inside back coverBSEN 1087-1:1995 ii BSI 09-1999 National foreword This British Standard has been prepared by Technical Committee B/541 and is the English language version of EN1087-1:1995 Particleboards Determination of moisture resistance Part 1: Boil test. EN 1087-1:199

8、5 was produced as a result of international discussion in which the United Kingdom took an active part. This method of test is not comparable with any of the methods of test given in BS1142:1989 Specification for fibre building boards, or BS5669-1:1989 Particleboard Part 1. Methods of sampling, cond

9、itioning and test, both of which will be withdrawn in due course. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity

10、 from legal obligations. Cross-references Publication referred to Corresponding British Standard EN 314-2:1993 BS EN 314 Plywood. Bonding quality Part 2:1993 Requirements EN 319:1993 BS EN 319:1993 Particleboards and fibreboards. Determination of tensile strength perpendicular to the plane of the bo

11、ard EN 325:1992 BS EN 325:1993 Wood-based panels. Determination of dimensions of test pieces Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 6, an inside back cover and a back cover. This standard has been updated (see copyr

12、ight date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1087-1 February 1995 ICS 79.060.20 Descriptors: Wooden boards, fibreboards, particleboards, moisture proofing, immersion t

13、ests, boiling water, tensile strength English version Particleboards Determination of moisture resistance Part 1: Boil test Panneaux de particules Dterminationdelarsistance lhumidit Partie 1. Essai leau bouillante Spanplatten BestimmungderFeuchtebestndigkeit Teil 1. Kochprfung This European Standard

14、 was approved by CEN on 1994-10-31. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nat

15、ional standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and n

16、otified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kin

17、gdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1995 Copyright reserved to CEN members Ref. No. EN 1087-1:1995 EEN 1087-1:1995 BSI 09-1999 2 Foreword This European Standard was pre

18、pared by Technical Committee CEN/TC112, Woodbased panels, of which the secretariat is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August1995, and conflicting national standards sh

19、all be withdrawn at the latest by August1995. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spa

20、in, Sweden, Switzerland, United Kingdom Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Principle 3 4 Apparatus 3 5 Test pieces 4 6 Procedure 5 7 Expression of results 5 8 Test report 5 Figure 1 Examples of apparatus for testing tensile strength perpendicular to the plane of the board

21、4EN 1087-1:1995 BSI 09-1999 3 1 Scope This European Standard specifies a method of test for evaluating the bond quality of particleboards, intended for use in humid conditions according to option2 of EN312-5 and EN312-7. 2 Normative references This European Standard incorporates, by dated or undated

22、 reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when inc

23、orporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. EN 312-5, Particleboards Specifications Part 5: Requirements for load-bearing boards for use in humid conditions 1) . EN 312-7, Particleboards Specifications Part 7: Requireme

24、nts for heavy duty load-bearing boards for use in humid conditions 1) . EN 314-2, Plywood Bonding quality Part 2: Requirements. EN 319, Particleboards and fibreboards Determination of tensile strength perpendicular to the plane of the board. EN 325, Wood-based panels Determination of dimensions of t

25、est pieces. EN 326-1, Wood-based panels Sampling, cutting and inspection Part 1: Sampling and cutting of test pieces and expression of test results. 3 Principle Tensile strength, perpendicular to the plane of the board (internal bond), is determined using test pieces which have been immersed in boil

26、ing water. 4 Apparatus 4.1 Sliding caliper A sliding caliper as specified in EN325. 4.2 Water bath Temperature controlled laboratory water bath, capable of raising the contents to boiling point at a specified rate (see6.1) and maintaining boiling for not less than 2h. 4.3 Testing machine As describe

27、d in EN319. 4.4 Testing blocks Blocks of either metal or plywood to which the test pieces are glued (seeFigure 1). Plywood blocks shall be made from beech plywood conforming to bonding class3 (exterior) of EN314-2. They shall be not less than 15mm in thickness and composed of not less than nine plie

28、s. Plywood of equivalent bending stiffness made from other species may be used. Solid wooden blocks shall not be used. When thin boards (800kg/m 3 ) are tested, metal blocks shall be used. 1) At present at the draft stage.EN 1087-1:1995 4 BSI 09-1999 5 Test pieces 5.1 Sampling Sampling and cutting o

29、f at least eight test pieces per panel shall be carried out according to the principles of EN326-1. 5.2 Dimensions As described in EN319. 5.3 Conditioning Both the test pieces and the plywood testing blocks shall be separately conditioned to constant mass in a standard climate of (20 2) C and relati

30、ve humidity of (65 5)%. Constant mass is considered to have been reached when the results of two successive weighing operations carried out at an interval of 24h do not differ by more than 0,1% of the mass. Figure 1 Examples of apparatus for testing tensile strength perpendicular to the plane of the

31、 boardEN 1087-1:1995 BSI 09-1999 5 5.4 Measurement of dimensions After conditioning, measure the length and width of each test piece according to EN325. 5.5 Bonding of the test pieces to the testing blocks Bond each test piece to testing blocks, using a suitable adhesive. The upper and lower blocks

32、shall be orientated at 90 as shown inFigure 1. Excess glue squeezed out from the glueline shall be removed before testing. When gluing, additional stresses affecting the test piece,e.g. caused by the moisture contained in the adhesive, and/or any rise in temperature, shall be avoided as far as possi

33、ble. NOTE 1The following combinations have proved suitable: epoxy resins with metal blocks epoxy resins, phenol-resorcinol resins and two component polyurethane resins with hardwood plywood blocks. NOTE 2The cleaning of metal blocks for re-use can be carried out as follows. After roughly removing th

34、e remains of the broken test pieces, the metal blocks are immersed in acetone for 12h to 24h. Thereafter, the remaining glue can be easily removed. WARNING: Acetone is highly flammable. Immersion in water shall only be carried out after the glue has had sufficient time to cure (so that rupture does

35、not occur in the glueline) and after the test pieces have had sufficient time to regain an equal distribution of moisture. During this time, the glued assembly shall be stored under controlled conditions of (65 5)% relative humidity and a temperature of (20 2) C. NOTE 3Experience has shown that equi

36、librium conditions are reached in approximately 24h if epoxy resins are used and approximately 72h if phenol-rescorcinol resins are used. 6 Procedure 6.1 Boil treatment Place the test pieces, glued to their testing blocks, in the water bath (4.2) and cover them with clean water, having a temperature

37、 of (20 5) C and a pH of7 0,5. They shall be separated from each other, and from the sides and bottom of the waterbath by at least 15mm, to allow free circulation of the water. This distance shall be maintained throughout the treatment. Renew the water at the start of each test. Heat the water to bo

38、iling point (. 100 C) over a period of (90 10)min. Continue boiling for(120 5) min. Remove and cool the test pieces. 6.2 Cooling of test pieces before testing Place and keep the test pieces in water at(20 5) C, immediately after removal from the boiling water, and leave them immersed for between1h a

39、nd 2h. Mop off excess water and test them in the wet condition. 6.3 Application of the load and measurement of failing load As described in EN319. 7 Expression of results As described in EN319. 8 Test report As described in EN326-1.6 blankBSEN 1087-1:1995 BSI 09-1999 List of references See national

40、foreword.BS EN 1087-1:1995 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revi

41、sions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambi

42、guity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers autom

43、atically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI i

44、mplementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic

45、 information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standa

46、rds. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under t

47、he Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implement

48、ing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.