BS EN 1253-1-2015 Gullies for buildings Trapped floor gullies with a depth water seal of at least 50 mm《建筑物集水沟 水封深度至少有50 mm的装有气隔的地面集水沟》.pdf

1、BSI Standards PublicationBS EN 1253-1:2015Gullies for buildingsPart 1: Trapped floor gullies with a depthwater seal of at least 50 mmBS EN 1253-1:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 1253-1:2015.This document, together with BS EN 1253-2:2015, sup

2、ersedes BS EN1253-1:2003 and BS EN 1253-2:2003, which are withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/505, Wastewater engineering.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not pur

3、port to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2015. Published by BSI StandardsLimited 2015ISBN 978 0 580 78397 5ICS 91.140.80Compliance with a British Standard cannot confer immunity fromlegal obligation

4、s.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 January 2015.Amendments issued since publicationDate Text affectedBS EN 1253-1:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1253-1 January 2015 ICS 91.140.80 Supersedes EN 1253-1

5、:2003, EN 1253-2:2003English Version Gullies for buildings - Part 1: Trapped floor gullies with a depth water seal of at least 50 mm Avaloirs et siphons pour btiments - Partie 1 : Siphons de sol avec garde deau de 50 mm minimum Ablufe fr Gebude - Teil 1: Bodenablufe mit Geruchverschluss mit einer Ge

6、ruchverschlusshhe von mindestens 50 mm This European Standard was approved by CEN on 22 November 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

7、Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by tra

8、nslation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finl

9、and, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATI

10、ON COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1253-1:2015 EBS EN 1253-1:2015EN 1253-1:2015 (E)

11、 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Requirements .8 4.1 Design and construction .8 4.2 Blockage prevention .9 4.3 Places of installation 10 4.4 Materials 10 4.5 Thermal behaviour of floor gullies 11 4.6 Tightness . 11 4.7 Mechanical strength .

12、11 4.8 Flow rates 13 5 Test methods . 14 5.1 Dimensions of apertures in gratings 14 5.2 Position of side inlets . 14 5.3 Water seal 15 5.4 Blockage prevention 16 5.5 Thermal behaviour 17 5.6 Loading test . 18 5.7 Mechanical strength . 22 5.8 Tightness . 24 5.9 Flow rates 26 6 Allocation and sequence

13、 of tests 27 7 Marking 28 8 Evaluation of conformity 28 Annex A (normative) Sequence of the tests 29 Annex B (informative) A-deviation 30 Bibliography . 31 BS EN 1253-1:2015EN 1253-1:2015 (E) 3 Foreword This document (EN 1253-1:2015) has been prepared by Technical Committee CEN/TC 165 “Waste water e

14、ngineering”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2015 and conflicting national standards shall be withdrawn at the latest by July 2015. At

15、tention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document, together with EN 1253-2:2015, supersedes EN 1253-1:2003 and EN 1253-2:200

16、3. This is the first part of EN 1253, a series of standards relating to floor gullies, roof drains and access covers for drainage systems inside buildings. The EN 1253 series under the main title Gullies for buildings will actually consist of the following parts: Part 1: Trapped floor gullies with a

17、 depth water seal of at least 50 mm; Part 2: Roof drains and floor gullies without trap; Part 3: Evaluation of conformity; Part 4: Access covers; Part 5: Gullies with light liquids closure. Since the latest versions of EN 1253-1 and EN 1253-2, the most significant technical changes are the following

18、: a) reduction of scope on trapped floor gullies with a depth of water seal of at least 50 mm for use in gravity drainage systems; b) more definitive description of products; c) modification of terms and definitions; d) precision in definition of places of installation; e) consideration of liquid ap

19、plied membranes as connecting components; f) precision of test conditions for flow rate testing; g) revision of loading test concerning test loads, loading speed as well as shape, size and point of impact of test blocks in dependence on different configuration of gratings; h) revision of tightness t

20、ests for products for use with sheet floor coverings, membranes and liquid applied membranes. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus,

21、 Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Ki

22、ngdom. BS EN 1253-1:2015EN 1253-1:2015 (E) 4 1 Scope This European Standard classifies floor gullies for use inside buildings, gives guidance for places of installation and specifies requirements for the construction, design, performance and marking of factory made gullies for buildings, irrespectiv

23、e of the material, for use in drainage systems requiring a trap with a depth of water seal of at least 50 mm (further: floor gullies). Although normally used to convey domestic wastewater, these floor gullies may convey other wastewater, e.g. industrial wastewater, provided there is no risk of damag

24、e to components or of injury to health. This European Standard does not apply to: linear drainage channels as specified in EN 1433, gully tops and manhole tops which are specified in EN 124, roof drains and floor gullies without trap as specified in EN 1253-2. 2 Normative references The following do

25、cuments, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 124, Gully tops and

26、manhole tops for vehicular and pedestrian areas - Design requirements, type testing, marking, quality control EN 476, General requirements for components used in drains and sewers EN 1253-3, Gullies for buildings - Part 3: Evaluation of conformity 3 Terms and definitions For the purposes of this doc

27、ument, the following terms and definitions apply. 3.1 trapped floor gully discharge fitting the top of which is a grating or cover capable of installation at ground or floor level, intended to receive wastewater either through apertures in the grating and/or from side inlets and/or channels joined t

28、o the body of the gully and to drain that wastewater through the outlet Note 1 to entry: See Figure 1. Note 2 to entry: In this European Standard, the term trapped “floor gully” includes linear products, such as channel drains. BS EN 1253-1:2015EN 1253-1:2015 (E) 5 a) Floor gully with side inlets an

29、d flange for bonding membranes (example) b) Floor gully with flange for clamping membranes (fixed and loose flange) (example) c) Floor gully with side inlets and flange for clamping flexible flooring (e.g. PVC flooring) (example) d) Channel drain with flange for bonding liquid applied membranes (exa

30、mple) Key 1 finished floor 10 weep hole 2 grating/cover 11 flange for bonding membranes 3 extension 12 sediment bucket 4 trap 13 connecting flange with counter flange 5 depth of water seal (H 50 mm) a fixed flange 6 outlet b loose flange 7 body 14 flange for clamping flexible flooring with a clampin

31、g ring 8 side inlet 15 seal 9 access for cleaning 16 flange for bonding liquid applied membrane Figure 1 Types of floor gullies 3.2 grating removable component with apertures which permits the discharge of water 3.3 frame support for a grating or cover which is connected to a body either directly or

32、 by means of a membrane clamping ring or an extension BS EN 1253-1:2015EN 1253-1:2015 (E) 6 3.4 cover removable part of an access cover which covers the opening 3.5 body part of a floor gully below or in the floor on which the grating/frame/extension is mounted, and to which the pipework is connecte

33、d 3.6 extension component used to adjust the height of a grating or cover above a body 3.7 joint connection between the adjacent ends of two components including the means of sealing 3.8 membrane clamping ring component used to clamp a membrane or a sheet floor covering to a body or extension 3.9 co

34、nnecting flange separate or an integral part of a body or of an extension which receives a membrane or sheet floor covering 3.10 external diameter OD mean external diameter of the pipe barrel at any cross section 3.11 internal diameter ID mean internal diameter of the pipe barrel at any cross sectio

35、n 3.12 trap removable or integral part of the body which prevents, by means of water seal, the passage of foul air from the outlet to the inlet 3.13 depth of water seal effective height of water in the trap (H) which prevents the passage of foul air Note 1 to entry: See Figure 1. 3.14 domestic waste

36、water water polluted by the human life, including water discharged from kitchens, laundry rooms, lavatories, bathrooms, toilets and similar facilities SOURCE: EN 16323:2014, 2.1.2.3 3.15 industrial wastewater wastewater discharge resulting from any industrial or commercial activity SOURCE: EN 16323:

37、2014, 2.1.2.7 BS EN 1253-1:2015EN 1253-1:2015 (E) 7 3.16 sheet floor covering flexible watertight finished layer for floors affixed to the flange by bonding, welding and/or by means of a clamping ring 3.17 membrane watertight and damp proof layer attached to the floor gully either in the floor or on

38、 the floor 3.18 head of water depth h of a water line over the frame of the floor gully Note 1 to entry: See Figure 2. Note 2 to entry: For floor gullies without frame, the depth of water line is the lowest level over the finished floor. Key h head of water Figure 2 Head of water for floor gullies 3

39、.19 outlet male or female connection to the discharge pipe 3.20 nominal size DN numerical indication of size which is a convenient integer approximately equal to the internal diameter (DN/ID) or the external diameter (DN/OD) in millimetres 3.21 clear opening CO diameter of the largest circle that ca

40、n be inscribed within the unsupported area of the grating BS EN 1253-1:2015EN 1253-1:2015 (E) 8 3.22 test load specified load which a component is required to withstand 3.23 liquid applied waterproofing kit particular combination of a defined set of components to be installed in liquid form for wate

41、rproofing by application and/or incorporation and/or joining of the components in accordance with particular design methods Note 1 to entry: The liquid applied watertight kit is usually a paste-like composite material or a combination of separate materials that can be poured, spread or sprayed on th

42、e subsurface by brush, roller or similar suitable applicator. 4 Requirements 4.1 Design and construction 4.1.1 General Floor gullies shall be capable of being connected to the pipework system covered by relevant European Standards, and, when installed in accordance with the manufacturers instruction

43、s, shall form an integral part of the building. There shall be no movement possible between the body and the floor, which would impair the functioning of the installed gully. In areas where pressure testing of the pipe system is necessary floor gullies for use in the ground floor shall enable such t

44、est to be performed. The upper surfaces of frame and grating shall be flush. When in position, it shall not be possible for gratings and covers to be dislodged from the frame, but they shall be easy to be released for e.g. maintenance and cleaning. Traps shall be prevented, by design features such a

45、s fixings or weights, from uncontrolled floating or becoming displaced. Floor gullies and their components shall be resistant to normal actions of mechanical and thermal character. Floor gullies may be designed with or without side inlet. Floor gullies shall be delivered with installation instructio

46、ns. All pipe joints to and from the floor gully shall be designed to be watertight in accordance with EN 476. 4.1.2 Appearance Internal and external surfaces shall be free from sharp edges and imperfections which could impair functioning of the floor gully or give risk of injury. 4.1.3 Apertures in

47、gratings Apertures can be holes or slots of any shape and may also be formed between grating and frame. When measured in accordance with 5.1, the permissible aperture dimensions for gratings are given in Table 1. BS EN 1253-1:2015EN 1253-1:2015 (E) 9 Table 1 Apertures in gratings Class Dimensions of

48、 apertures in gratings Minimum width mm Maximum width mm H 1,5 K 3 L 15 aR50 aM 125 aN 250 P 400 4 b4 b4 4 4 4 4 15 (max. 8 mm in barefoot areas) 10 (max. 8 mm in barefoot areas) 15 (max. 8 mm in barefoot areas) 25 (max. 8 mm in barefoot areas) 25 25 25 aIn commercially used premises, gratings may a

49、lso be used with a maximum width of apertures up to 31 mm. bApertures of less than 4 mm width are permitted and shall not form part of the hydraulic tests. 4.1.4 Side inlets There are two types of floor gully with side inlets as follows: 1) Type I: side inlets either partially or totally below the water level; 2) Type II: side inlets completely above the water level. The positioning of side inlets shall be checked in accordance with 5.2. 4.1.5 Depth of water seal Floor gullies for wastewater shall provide a minimum depth of water seal H of 50 mm a