BS EN 1254-3-1998 Copper and copper alloys Plumbing fittings Fittings with compression ends for use with plastics pipes《铜和铜合金 管路接头 与塑料管一起使用的压合接头》.pdf

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 1254-3:1998 The Eur

2、opean Standard EN 1254-3:1998 has the status of a British Standard ICS 23.040.40 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Copper and copper alloys Plumbing fittings Part 3: Fittings with compression ends for use with plastics pipesThis British Standard, having been prep

3、ared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 June 1998 BSI 1998 ISBN 0 580 29440 4 BS EN 1254-3:1998 Amendments issued since publication Amd. No. Date Text affected National foreword This British Standa

4、rd is the English language version of EN 1254-3:1998. It supersedes BS 864-5:1990 which is declared obsolescent. The UK participation in its preparation was entrusted by Technical Committee NFE/34, Copper and copper alloys, to Subcommittee NFE/34/3, Copper and copper alloy fittings for tube and pipe

5、, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the

6、UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled

7、“International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance w

8、ith a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 13 and a back cover.CEN European Committee for Standardization Comite Europe en de Normalisation Europa ische

9、s Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1254-3:1998 E EUROPEAN STANDARD EN 1254-3 NORME EUROPE ENNE EUROPA ISCHE NORM January 1998 ICS 23.

10、040.40 Descriptors: Plastic tubes, copper, copper alloys, pipe fittings, joining, dimensions, dimensional tolerances, design, manufacturing, tests, designation, marking English version Copper and copper alloys Plumbing fittings Part 3: Fittings with compression ends for use with plastics pipes Cuivr

11、e et alliages de cuivre Raccords Partie 3: Raccords a compression pour tuyaux en plastique Kupfer und Kupferlegierungen Fittings Teil 3: Klemmverbindungen fu r Kunststoffrohre This European Standard was approved by CEN on 24 November 1998. CEN members are bound to comply with the CEN/CENELEC Interna

12、l Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.

13、This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are

14、 the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN 1254-3:1998 BSI 1998 Foreword This European Standard has been pre

15、pared by Technical Committee CEN/TC 133, Copper and copper alloys, the Secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 1998, and conflicting national stan

16、dards shall be withdrawn at the latest by July 1998. Within its programme of work, Technical Committee CEN/TC 133 requested CEN/TC 133/WG 8, Copper and copper alloy fittings, to prepare the following standard: EN 1254-3, Copper and copper alloys Plumbing fittings Part 3: Fittings with compression en

17、ds for use with plastics pipes. This standard is one of five parts for copper and copper alloy fittings for joining copper tubes or plastics pipes. The other four parts of the standard are: EN 1254-1, Copper and copper alloys Plumbing fittings Part 1: Fittings with ends for capillary soldering or ca

18、pillary brazing to copper tubes. EN 1254-2, Copper and copper alloys Plumbing fittings Part 2: Fittings with compression ends for use with copper tubes. EN 1254-4, Copper and copper alloys Plumbing fittings Part 4: Fittings combining other end connections with capillary or compression ends. EN 1254-

19、5, Copper and copper alloys Plumbing fittings Part 5: Fittings with short ends for capillary brazing to copper tubes. It is recommended that fittings manufactured to this standard are certified as conforming to the requirements of this standard, based on third party testing and continuing surveillan

20、ce, which should be coupled with an assessment of a suppliers quality system against the appropriate standard, i.e. EN ISO 9001 or EN ISO 9002. In respect of potential adverse effects on the quality of water intended for human consumption caused by the product covered by this standard: a) this stand

21、ard provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA; b) it should be noted that, while awaiting the adoption of verifiable European criteria, existing national regulations concerning the use and/or the characteristics of

22、 this product remain in force. The attention of the user of this standard is drawn to the fact that national or local regulations or practices might restrict the choice of dimensions and threads in the application of products conforming to this standard. According to the CEN/CENELEC Internal Regulat

23、ions, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the Uni

24、ted Kingdom. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Definitions 3 3.1 plumbing fitting 3 3.2 compression end 3 3.3 reducer (compression end with plastic pipe) 4 3.4 adaptor fitting 4 3.5 nominal diameter 4 3.6 production test 4 3.7 type test 4 4 Requirements 4 4.1 General 4 4.

25、2 Materials 4 4.3 Dimensions and tolerances 4 4.4 Design and manufacture 7 4.5 Production test requirements 7 4.6 Type test requirements 7 5 Test methods 8 5.1 Pressure test 8 5.2 Dezincification resistance test 8 5.3 Leaktightness under internal pressure 8 5.4 Resistance to pull-out 8 5.5 Leaktight

26、ness under internal pressure whilst subjected to bending 8 5.6 Leaktightness under external hydrostatic pressure 8 5.7 Vacuum test 8 5.8 Thermal cycling test 8 5.9 Pressure cycling test 8 5.10 Stress corrosion resistance test 8 6 Designation 8 7 Marking 9 7.1 General 9 7.2 Dezincification resistant

27、copper-zinc alloys 9 8 Documentation 9 8.1 Declaration of conformity 9 8.2 User instructions 9 Annex A (informative) Types of fitting and description of parts 10 Annex B (normative) Test criteria, depending on application and plastics pipe material, to test pipe joints of metallic fittings with comp

28、ression ends 12 Annex C (normative) Determination of mean depth of dezincification 12 Annex D (informative) Bibliography 13Page 3 EN 1254-3:1998 BSI 1998 1 Scope This European Standard specifies materials, assembly dimensions and tolerances and test requirements for fittings of copper and copper all

29、oys with or without plating or coating. This part of EN 1254 specifies connection end dimensions of compression ends for the purpose of joining plastics pipes for use in cold or combined hot and cold water systems or non-fuel gas systems. Fittings may comprise a combination of any of the end types s

30、pecified in EN 1254-1 to EN 1254-5 or other standards. The standard establishes a designation system for the fittings. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriat

31、e places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publicatio

32、n referred to applies. EN 712, Thermoplastics piping systems End-load bearing mechanical joints between pressure pipes and fittings Test method for resistance to pull-out under constant longitudinal force. EN 713, Plastics piping systems Mechanical joints between fittings and polyolefin pressure pip

33、es Test method for leaktightness under internal pressure of assemblies subjected to bending. EN 715, Thermoplastics piping systems End-load bearing joints between small diameter pressure pipes and fittings Test method for leaktightness under internal water pressure, including end thrust. EN 911, Pla

34、stics piping systems Elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping Test method for leaktightness under external hydrostatic pressure. EN 1254-1, Copper and copper alloys Plumbing fittings Part 1: Fittings with ends for capillary soldering or capillary

35、brazing to copper tubes. EN 1254-2, Copper and copper alloys Plumbing fittings Part 2: Fittings with compression ends for use with copper tubes. EN 1254-4, Copper and copper alloys Plumbing fittings Part 4: Fittings combining other end connections with capillary or compression ends. EN 1254-5, Coppe

36、r and copper alloys Plumbing fittings Part 5: Fittings with short ends for capillary brazing to copper tubes. prEN 12201-5, Plastics piping systems for water supply Polyethylene (PE) Part 5: Fitness for purpose of the system. prEN 12202-5, Plastics piping systems for hot and cold water Polypropylene

37、 (PP) Part 5: Fitness for purpose of the system. prEN 12293, Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of mounted assemblies to temperature cycling. prEN 12294, Plastics piping systems Systems for hot and cold water Test method fo

38、r leaktightness under vacuum. prEN 12295, Plastics piping systems Thermoplastics pipes and associated fittings for hot and cold water Test method for resistance of joints to pressure cycling. prEN 12318-5, Plastics piping systems for hot and cold water Cross-linked polyethylene (PE-X) Part 5: Fitnes

39、s for purpose of the system. prEN 12319-5, Plastics piping systems for hot and cold water Polybutylene (PB) Part 5: Fitness for purpose of the system. EN 12731-5, Plastics piping systems for hot and cold water Chlorinated poly(vinyl chloride) (PVC-C) Part 5: Fitness for purpose of the system. EN ISO

40、 6509: 1995, Corrosion of metals and alloys Determination of dezincification resistance of brass. (ISO 6509: 1981) ISO 6957, Copper alloys Ammonia test for stress corrosion resistance. NOTE Informative references to documents used in the preparation of this standard, and cited at the appropriate pla

41、ces in the text, are listed in a bibliography, see annex D. 3 Definitions For the purposes of this standard, the following definitions apply: 3.1 plumbing fitting device used in a piping system for the purpose of connecting the pipes either to each other or to a component part of a system NOTE See a

42、nnex A for types of fitting and description of parts. 3.2 compression end end in which the joint is made by the compression of a ring or sleeve on the outside wall of the pipe 3.2.1 compression end, type A end that requires no preparation of the ends of the pipe other than that they are cut square a

43、nd deburred or chamfered when specified, and in which the joint is made by the compression of a ring or sleeve onto the outside wall of the pipe with or without additional sealing elements and with or without an internal pipe supportPage 4 EN 1254-3:1998 BSI 1998 3.2.2 compression end, type B end th

44、at requires forming of the pipe at its end, and in which the joint is made by compressing the formed portion of the pipe against the formed end of the fitting or a loose ring or sleeve within the fitting/pipe 3.3 reducer (compression end with plastic pipe) component or components used to enable a co

45、mpression end to connect pipe of a smaller nominal diameter than the nominal diameter of the fitting end 3.4 adaptor fitting fitting combining more than one type of end NOTE For details of the other ends, see the relevant parts of this standard or other standards. 3.5 nominal diameter nominal diamet

46、er of the fitting end expressed as the nominal outside diameter of the connecting pipe 3.6 production test test performed by the manufacturer on materials or components at specific intervals to confirm that the process continues to be capable of producing components conforming to the requirements of

47、 the product specification NOTE Such tests are not required to release batches of components but are carried out as a measure of process control. 3.7 type test test or series of tests directed towards approval of a design, conducted to prove that an item is capable of meeting the requirements of the

48、 product specification 4 Requirements 4.1 General Fittings shall conform to the requirements of 4.2 to 4.5 and shall be capable of meeting the type testing requirements of 4.6, which are those required by the relevant plastics piping systems standards and are dependent on specific applications. Redu

49、cers shall also conform to these requirements. 4.2 Materials Fittings shall be made from copper or copper alloys selected from materials that are either: specified in European copper and copper alloy product standards; or registered by CEN/TC 133; provided that the fittings manufactured from them meet the functional requirements of this standard. NOTE 1 Some of the standardized coppers and copper alloys commonly used for the manufacture of fittings are show