1、BSI Standards PublicationBS EN 1396:2015Aluminium and aluminiumalloys Coil coated sheet andstrip for general applications SpecificationsBS EN 1396:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 1396:2015. It supersedes BS EN 1396:2007 which is withdrawn.Th
2、e UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract.
3、Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 83721 0 ICS 77.150.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authori
4、ty of the Standards Policy and Strategy Committee on 30 April 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1396 April 2015 ICS 77.150.10 Supersedes EN 1396:2007English Version Aluminium and aluminium alloys - Coil
5、 coated sheet and strip for general applications - Specifications Aluminium et alliages daluminium - Tles et bandes revtues en bobine pour applications gnrales - Spcifications Aluminium und Aluminiumlegierungen - Bandbeschichtete Bleche und Bnder fr allgemeine Anwendungen - Spezifikationen This Euro
6、pean Standard was approved by CEN on 31 January 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references c
7、oncerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member
8、 into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, Franc
9、e, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOM
10、ITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1396:2015 EBS EN 1396:2015Contents Page Foreword 4 Introduction . 5 1 Scope 6 2 Normative referen
11、ces 6 3 Terms and definitions . 7 4 Technical conditions for inspection and delivery 9 4.1 Ordering information . 9 4.2 Requirements . 11 4.2.1 Production and manufacturing processes . 11 4.2.2 Quality control . 11 4.2.3 Freedom from defects . 11 4.2.4 Chemical composition 11 4.2.5 Mechanical proper
12、ties . 11 4.2.6 Tolerances on shape and dimensions 11 4.2.7 Coating properties . 12 4.3 Test procedures . 12 4.3.1 Chemical composition 12 4.3.2 Tensile test . 12 4.3.3 Coating tests 12 4.3.4 Retests 13 5 Mechanical properties . 13 6 Organic coating properties . 15 6.1 Tolerances on thickness . 15 6
13、.2 Tolerances on gloss 16 6.3 Tolerances on colour 17 7 Inspection documents . 17 8 Marking . 17 9 Packing . 17 10 Arbitration tests . 18 Annex A (normative) Rules for rounding 19 Annex B (informative) Examples of coating systems 20 Annex C (informative) Guidelines for organic coatings 22 C.1 Genera
14、l 22 C.2 Colour . 22 C.3 Flexibility 22 C.4 Adhesion. 23 C.5 Pencil hardness . 24 C.6 Durability of the organic coating . 24 C.6.1 General 24 C.6.2 Corrosion resistance (outdoor exposure) . 26 EN 1396:2015 (E)BS EN 1396:2015EN 1396:2015 (E) 3 C.6.3 UV resistance . 26 C.6.3.1 General . 26 C.6.3.2 Nat
15、ural outdoor UV radiation resistance tests . 27 C.6.3.3 UV radiation resistance ( accelerated test) . 28 C.6.4 Humidity resistance (accelerated test) 28 C.6.5 Acetic acid salt spray fog resistance (accelerated corrosion test) 28 C.6.6 Filiform corrosion test, FFC (accelerated corrosion test) . 28 An
16、nex D (informative) Guidelines for storage and subsequent processing . 30 D.1 Storage . 30 D.2 General instructions for processing . 30 D.3 Forming 30 D.4 Cutting 30 D.5 Joining 31 D.6 Cleaning . 31 D.7 Temporary protective films 31 Bibliography 32 BS EN 1396:2015Foreword This document (EN 1396:2015
17、) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2015 and
18、conflicting national standards shall be withdrawn at the latest by October 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This
19、document supersedes EN 1396:2007. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav
20、Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. EN 1396:2015 (E)BS EN 1396:2015EN 1396:2015 (E) 5 Int
21、roduction Organic coated aluminium and aluminium alloy strip and sheet products can be used to advantage in cases where corrosion resistance and decorative appearance are of primary importance. They have applications throughout the flat products processing industry e.g. in the building, automotive,
22、caravans, appliances, fabricating and packaging industries. Organic coated aluminium and aluminium alloy flat products can be delivered in numerous types and grades, depending on the base material used (various grades of aluminium), on the coating material and types of coating and on the requirement
23、s for the surface appearance and the formability. The properties of the products can vary within greater or smaller limits depending on the choice and combination of properties required. It is therefore not practicable to specify in detail minimum requirements for all properties for all types of pro
24、ducts. As a general rule, material specifications shall be agreed between manufacturer and user/purchaser using, when appropriate, the guidelines from Annex C. Guidelines for proper storage and subsequent processing of organic coated aluminium flat products are given in Annex D. BS EN 1396:20151 Sco
25、pe This European Standard specifies the particular requirements for wrought aluminium and wrought aluminium alloys in the form of coil coated sheet and strip for general applications. This product is generally supplied in thicknesses up to 3,0 mm. It applies to cold-rolled aluminium and aluminium al
26、loy strip coated by the coil coating process both with liquid as well as with powder paints, either in the final width or slit afterwards, and to sheet obtained from such strip. It does not apply to coil coated sheet and strip used for special applications such as cans, closures and lids which are d
27、ealt with in separate EN 541. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced
28、 document (including any amendments) applies. EN 485-1, Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for inspection and delivery EN 485-4, Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled pr
29、oducts EN 515, Aluminium and aluminium alloys - Wrought products - Temper designations EN 573-3, Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products EN 12258-1:2012, Aluminium and aluminium alloys - Terms and definiti
30、ons - Part 1: General terms EN 13523-1, Coil coated metals - Test methods - Part 1: Film thickness EN 13523-2, Coil coated metals - Test methods - Part 2: Gloss EN 13523-3, Coil coated metals - Test methods - Part 3: Colour difference - Instrumental comparison EN 13523-4, Coil coated metals - Test m
31、ethods - Part 4: Pencil hardness EN 13523-6, Coil coated metals - Test methods - Part 6: Adhesion after indentation (cupping test) EN 13523-7, Coil coated metals - Test methods - Part 7: Resistance to cracking on bending (T-bend test) EN 13523-8, Coil coated metals - Test methods - Part 8: Resistanc
32、e to salt spray (fog) EN 13523-10, Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation EN 13523-19, Coil coated metals - Test methods - Part 19: Panel design and method of atmospheric exposure testing EN 13523-21, Coil coated metals - Test metho
33、ds - Part 21: Evaluation of outdoor exposed panels EN 13523-22, Coil coated metals - Test methods - Part 22: Colour difference - Visual comparison EN ISO 1520, Paints and varnishes - Cupping test (ISO 1520) EN 1396:2015 (E)BS EN 1396:2015EN 1396:2015 (E) 7 EN ISO 4628-2, Paints and varnishes - Evalu
34、ation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 2: Assessment of degree of blistering (ISO 4628-2) EN ISO 6270-1, Paints and varnishes - Determination of resistance to humidity - Part 1: Continuous condensation
35、(ISO 6270-1) EN ISO 6272-1, Paints and varnishes - Rapid-deformation (impact resistance) tests - Part 1: Falling-weight test, large-area indenter (ISO 6272-1) EN ISO 6272-2, Paints and varnishes - Rapid-deformation (impact resistance) tests - Part 2: Falling-weight test, small-area indenter (ISO 627
36、2-2) EN ISO 6892-1:2009, Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2009) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12258-1:2012 and the following apply. 3.1 aluminium unalloyed aluminium or alu
37、minium alloy Note 1 to entry: In the USA the term “Aluminum” is used. SOURCE: EN 12258-1: 2012 3.2 aluminium alloy aluminium which contains alloying elements, where aluminium predominates by mass over each of the other elements and where the aluminium content is not greater than 99,00% SOURCE: EN 12
38、258-1:2012 3.3 metal substrate base material from cold rolled aluminium or aluminium alloy strip 3.4 coating material material comprising organic polymers e.g. synthetic resins or plastics, to which pigments, additives and sol- vents (if required) have generally been added, suitable for coil coating
39、 Note 1 to entry: These can be paints (liquid or powder) or plastic films. 3.5 coil coating method in which a coating material is applied in a continuous process on a cold rolled metal strip Note 1 to entry: This process includes cleaning and chemical pre-treatment of the surface and either: one-sid
40、e or two-side, single or multiple application of liquid or powder coating materials which are subsequently cured, or laminating with plastic films. BS EN 1396:20153.6 organic coating paint or lacquer film on a coated product produced from wet paint or from powder coating, or the laminated organic fi
41、lm SOURCE: EN 12258-1:2012 3.7 top side side of the strip with the highest decorative demand and which, in normal production, is uppermost Note 1 to entry: For strip supplied in coil form, the top side is normally the outside of the coil. For sheet supplied in stacks or bundles the top side is norma
42、lly uppermost. 3.8 reverse side underside of the strip, generally coated with a backing coat (see 3.12), but possibly pre-treated only or coated with one of the other systems described in 3.10, 3.11 and 3.13, to fulfil special requirements such as foam or glue adhesion, specially defined friction, e
43、tc. 3.9 coating system combination of coatings either on the top side or on the reverse side of the metal substrate Note 1 to entry: The name of the coating system derives from the top coat coating material (see examples in Annex B). 3.10 single layer coating single coating either with requirements
44、on appearance, formability, corrosion protection, subsequent painting etc., or as a primer with special properties regarding adhesion and corrosion protection for post-painting applications 3.11 multilayer coating system comprising a primer or a base coat, possibly intermediate coat(s), and a top co
45、at with particular requirements on appearance, formability, corrosion protection etc. 3.12 backing coat single coating of any type with no particular requirements for appearance, formability, corrosion protection etc., usually on the reverse side of the coated product 3.13 film coating organic film
46、applied to a substrate to which an adhesive and, if appropriate, a primer has been applied before- hand SOURCE: EN 12258-1:2012 3.14 master coil / mother coil coil-coated in coil from which products (coil or sheet) are obtained EN 1396:2015 (E)BS EN 1396:2015EN 1396:2015 (E) 9 3.15 order document do
47、cument or set of documents agreed between supplier and purchaser at the time of ordering Note 1 to entry: An order document can be an order of the purchaser confirmed by the supplier or a quotation of the supplier confirmed by the purchaser. 4 Technical conditions for inspection and delivery 4.1 Ord
48、ering information The order document shall define the product required and shall contain the following information: a) the form and type of product: the form of the product (organic coated coil, sheet or strip); the designation of the aluminium or aluminium alloy, in accordance with EN 573-3; b) the
49、 temper of the material for delivery (degree of hardness or heat treatment condition) in accordance with EN 515 and EN ISO 6892-1:2009; c) the dimensions and shape of the product: thickness (of the metal substrate); width; length of sheet (in the rolling direction); internal and external diameters of the coil; core size and type. NOTE Unless otherwise agreed, the length is the largest dimension;. d) the quantity: mass or number of pieces; e) the coating system (see examples in Annex B): 1) for the top side: colour designation (international a
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1