BS EN 1412-2016 Copper and copper alloys European numbering system《铜和铜合金 欧洲牌号系统》.pdf

1、BS EN 1412:2016Copper and copper alloys European numbering systemBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 1412:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 1412:2016.It supersedes BS EN 1412:1996 which is wit

2、hdrawn.The UK participation in its preparation was entrusted to Technical Committee NFE/34, Copper and copper alloys.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contra

3、ct. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 92585 6 ICS 77.120.30 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the aut

4、hority of the Standards Policy and Strategy Committee on 31 December 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 1412:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1412 November 2016 ICS 77.120.30 Supersedes EN 1412:1995English Version Copper and c

5、opper alloys - European numbering system Cuivre et alliages de cuivre - Systme europen de dsignation numrique Kupfer und Kupferlegierungen - Europisches Werkstoffnummernsystem This European Standard was approved by CEN on 30 September 2016. CEN members are bound to comply with the CEN/CENELEC Intern

6、al Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any C

7、EN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official vers

8、ions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

9、Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitat

10、ion in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1412:2016 EBS EN 1412:2016EN 1412:2016 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Terms and definitions . 5 3 Details of the system 5 3.1 General 5 3.2 Structure of numbers . 5 3.2.1 C

11、omplete number 5 3.2.2 Position of characters 5 4 Allocation and administration of material numbers . 6 Bibliography 7 Tables Table 1 Significance of positions 3 to 6 6 BS EN 1412:2016EN 1412:2016 (E) 3 European foreword This document (EN 1412:2016) has been prepared by Technical Committee CEN/TC 13

12、3 “Copper and copper alloys”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2017, and conflicting national standards shall be withdrawn at the latest

13、 by May 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1412:1995. In comparison with EN 1412:1995, the following s

14、ignificant changes were made: a) allocation of ranges for the numeric part of a material number to material groups; b) addition of provisions how to assign the numeric part of a material number to individual materials; c) removal of the provisions for not standardized materials. According to the CEN

15、-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungar

16、y, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 1412:2016EN 1412:2016 (E) 4 Introduction The numbering system described in this European Standard is

17、an alternative to the material symbol designation system given in ISO 1190-1. BS EN 1412:2016EN 1412:2016 (E) 5 1 Scope This European Standard establishes a numbering system for designation copper or copper alloys manufactured and/or used in Europe and the responsibility for the allocation and admin

18、istration of numbers for individual copper materials. The system is applicable to copper materials standardized in European Standards. 2 Terms and definitions For the purposes of this document, the following term and definition applies. 2.1 copper material general term for copper and copper alloys 3

19、 Details of the system 3.1 General The number shall be composed of alphabetic (upper case Latin letters) and numeric (Arabic) characters. The system shall provide only one number for each material. A number assigned to an individual material shall not be assigned to another material even if the firs

20、t mentioned material has been withdrawn. 3.2 Structure of numbers 3.2.1 Complete number The number shall consist of six characters. 3.2.2 Position of characters 3.2.2.1 General The positions of characters are as follows: 1 2 3 4 5 6 3.2.2.2 Position 1 The character for the first position shall be th

21、e letter “C” to designate copper material. 3.2.2.3 Position 2 The character for the second position shall be one of the following letters, whose significance is given as follows: B materials in ingots form for remelting to produce cast products; C materials in the form of cast products; F filler mat

22、erials for brazing and welding; M master alloys; R refined unwrought copper; S materials in the form of scrap; BS EN 1412:2016EN 1412:2016 (E) 6 W materials in the form of wrought products. 3.2.2.4 Position 3 to 5 The character for the third, fourth and fifth positions shall be a number from the ran

23、ge allocated to one of the material groups given in Table 1. There is no particular significance attributed to any of these characters within one range. The same number shall be assigned to materials with the same chemical composition (e.g. material in the form of wrought products and the same mater

24、ial in form of scrap). Materials with a different chemical composition shall not be assigned to the same number, unless the materials are in a direct process flow (e.g. material in ingots form for remelting to produce cast products and the corresponding material in form of cast products). 3.2.2.5 Po

25、sition 6 The character for the 6th position shall be a letter designating one of the material groups given in Table 1. There is no particular significance attributed to any of these letters within one material group. 3.2.2.6 Examples CW024A; CB752S; CC383H. 4 Allocation and administration of materia

26、l numbers NOTE CEN/TC 133 is responsible for the allocation and administration of material numbers. Table 1 Significance of positions 3 to 6 Material group Position 3, 4 and 5a(a number in the range) Position 6 (letter designating material group) Copper 000 to 099 A or B Copper alloys, low alloyed (

27、less than 5 % alloying elements) 100 to 199 C or D Miscellaneous copper alloys (5 % or more alloying elements) 200 to 299 E or F Copper-aluminium alloys 300 to 349 G Copper-nickel alloys 350 to 399 H Copper-nickel-zinc alloys 400 to 449 J Copper-tin alloys 450 to 499 K Copper-zinc alloys, binary 500

28、 to 599 L or M Copper-zinc-lead alloys 600 to 699 N or P Copper-zinc alloys, complex 700 to 799 R or S aRange of 800 to 999 to be used as a reserve. BS EN 1412:2016EN 1412:2016 (E) 7 Bibliography 1 ISO 1190-1, Copper and copper alloys Code of designation Part 1: Designation of materials This page de

29、liberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BS

30、I Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a

31、 dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British

32、 Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be pur

33、chased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI

34、or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the st

35、andard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in sof

36、t copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or i

37、nternal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1

38、 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur rang

39、e of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its availab

40、le 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusi

41、ve to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standa

42、rds publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment

43、or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Ema

44、il (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20