BS EN 1519-1-2000 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure Polyethylene (PE) Specifications for pipes fittings .pdf

1、BRITISH STANDARD BS EN 1519-1:2000 Incorporating Corrigendum No. 1 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure Polyethylene (PE) Part 1: Specifications for pipes, fittings and the system The European Standard EN 1519-1:1999 has the st

2、atus of a British Standard ICS 23.040.01; 83.140.30; 91.140.80 BS EN 1519-1:2000 This British Standard, having been prepared under the direction of the Materials and Chemicals Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 15

3、 February 2000 BSI 6 November 2002 ISBN 0 580 35935 2 National foreword This British Standard is the official English language version of EN 1519-1:1999. It is one of a group of EN standards which each partially supersede BS 5255:1989. BS 5255:1989 will be declared obsolescent with effect from 2001-

4、06-30. Products conforming to BS EN 1519-1 will be compatible with those of the same size in accordance with BS 5255:1989. The nominal sizes DN/OD 38, 44 and 57 correspond exactly with the 1 , 1 and 2 sizes respectively in BS 5255:1989. Since EN 1519-1:1999 does not cover all the piping components c

5、overed by or used in conjunction with products conforming to BS 5255, see BS 4514:1983 and its planned revision for the UK requirements for the minimum opening dimensions of access fittings, design of swept fittings, for connectors to WC pans and stand-off dimensions of pipe and fitting clips. The U

6、K participation in its preparation was entrusted by Technical Committee PRI/61, Plastics piping systems and components, to Subcommittee PRI/61/1, Thermoplastics piping systems and components for non-pressure applications, which has the responsibility to: A list of organizations represented on this s

7、ubcommittee can be obtained on request to its secretary. The responsible UK committee gives the following advice concerning the selection of alternative test conditions provided in this standard. a) Table 10, as referred to in 7.1, appears to present two alternative test conditions, i.e. method A or

8、 method B of EN 743:1994, without identifying where they apply or which is the reference method in case of dispute. Since these alternative test conditions might lead to conflicting results, users of this standard should declare or agree on a contractual basis which condition is to be the reference

9、condition in case of dispute. b) In Table 14, reference is made to a specific point of detail in the current edition of EN 921, i.e. “types a or b” end caps, and therefore: 1) the reference should be construed as relating to the current (1995) edition, as though the reference in Table 14 and hence a

10、lso in clause 2, was dated accordingly; 2) since alternative test conditions are permitted which might lead to conflicting results, depending on the choice of end caps, users of this standard should declare or agree on a contractual basis which condition is to be the reference condition in case of d

11、ispute. The responsible UK committee gives the following advice concerning the specification of piping components used with piping systems conforming to this British Standard but not detailed in EN 1519-1:1999. aid enquirers to understand the text; present to the responsible international/European c

12、ommittee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Amendments issued since publication Amd. No. Date Comments 13817 Corrigendum No. 1 6 November 2002 Revisio

13、n of national forewordBS EN 1519-1:2000 BSI 6 November 2002 i c) See BS 4514:2001 for the UK requirements for the minimum opening dimensions of access fittings, design of swept fittings, connectors to WC pans, stand-off dimensions of pipe and fitting brackets and requirements for adaptors and plugs.

14、 Reference should also be made to the following design requirements of BS 4514:2001, 5.3.1, 5.3.3, 5.3.5, 5.3.7, 5.3.8, 5.3.9, and Figures 6, 8 and 9. Analogous provisions apply in Scotland and Northern Ireland. d) For external installation, which is commonplace and remains allowed in the UK, EN 151

15、9-1:1999 only requires that additional requirements depending on the climate be agreed between the manufacturer and the user (in clause 12: otherwise, in line with European practice, EN 1519-1:1999 only gives specific requirements for products for discharge systems intended to be installed within bu

16、ildings.) If the product is to be installed externally, it may require protection by painting or some other means. The responsible UK committee gives the following advice concerning the selection and installation of piping systems and components conforming to this British Standard. e) The products s

17、hould only be used in application area B, i.e. suspended from brackets above ground and installed in accordance with BS 5572 using the N socket variants as specified. For external installation, see item d) of this foreword. The advice of the manufacturer of products conforming to BS EN 1519-1 should

18、 be sought accordingly. f) In respect of fire regulations (see 4.7), for England and Wales The Building Regulations 1991, Approved Document B3, Section 10 requires that where PE pipe with an internal diameter greater than 40 mm (1 ) penetrates a fire wall, floor or enclosure the point of penetration

19、 is protected by a proprietary fire seal. This seal must be certificated by third party testing to show that it is effective with PE pipes. Analogous provisions apply in Scotland and Northern Ireland respectively. g) For underground installations, see BS EN 12666-1 or equivalent product specificatio

20、ns for such situations and take account of current national installation practices, e.g. BS EN 1610 and BS EN 752. Editorial note: Reference to regulations In 4.4 the only “requirement” is that “pipes and fittings. shall conform to any relevant requirements on fire regulations”. Since the authority

21、for such requirements lies with national regulators and not with standards organizations, which do not have the power to waive regulations even should they so wish, this type of information in standards should be presented as a note, or as a statement in a foreword or introduction. As information it

22、 can refer in general or specific terms to the existence of current regulations/legislation/directives applicable to the products or the conditions of their use. The expression here as part of the normative text is inappropriate and should not be considered an acceptable precedent for other standard

23、s to follow. Warning This British Standard, which is identical with EN 1519-1:1999, does not necessarily detail all the precautions necessary to meet the requirements of the Health and Safety at Work etc. Act 1974. Attention should be paid to any appropriate safety precautions and the test methods r

24、eferred to in EN 1519-1 should be operated only by trained personnel. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”

25、, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer

26、 immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, page i, a blank page, the EN title page, pages 2 to 29 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued.ii blankEUROPEAN STA

27、NDARD NORME EUROPENNE EUROPISCHE NORM EN 1519-1 July 1999 ICS 23.040.20 English version Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system Systmes de canalisatio

28、ns en plastiques pour lvacuation des eaux-vannes et des eaux uses ( basse et haute temprature) lintrieur de la structure des btiments - Polythylne (PE) - Partie 1: Spcifications pour tubes, raccords ainsi que pour le systme Kunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hohe

29、r Temperatur) innerhalb der Gebudestruktur - Polyethylen (PE) - Teil 1: Anforderungen an Rohre, Formstcke und das Rohrleitungssystem This European Standard was approved by CEN on 7 November 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions

30、 for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three offic

31、ial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, B

32、elgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Central Secretari

33、at: rue de Stassart, 36 B-1050 Brussels 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1519-1:1999 EPage 2 EN 1519-1:1999 BSI 02-2000 Contents Page Foreword. 3 1 Scope . 4 2 Normative references. 5 3 Definitions, symbols and

34、abbreviations. 7 3.1 Definitions 7 3.2 Symbols . 8 3.3 Abbreviations . 8 4M a t e r i a l 9 4.1 PE-compound 9 4.2 Reprocessable and recyclable material 9 4.3 Melt mass-flow rate 9 4.4 Fusion compatibility 9 4.5 Thermal stability. 9 4.6 Sealing ring retaining means. 9 4.7 Fire behaviour . 9 5 General

35、 characteristics. 10 5.1 Appearance 10 5.2 Colour. 10 6 Geometrical characteristics . 10 6.1 General 10 6.2 Dimensions of pipes 10 6.3 Dimensions of fittings. 12 6.4 Dimensions of sockets and pipe ends 13 6.5 Types of fittings 18 7 Physical characteristics 22 7.1 Physical characteristics of pipes .

36、22 7.2 Physical characteristics of fittings 22 8 Performance requirements. 23 9 Requirements for application area “BD”.24 9.1 General 24 9.2 Material characteristics 25 9.3 Mechanical characteristics 25 10 Sealing rings 25 11 Marking . 26 11.1 General 26 11.2 Minimum required marking of pipes . 26 1

37、1.3 Minimum required marking of fittings 26 12 Installation of piping systems 27 Annex A (informative) General characteristics of PE pipes and fittings . 28 A.1 General 28 A.2 Material characteristics . 28 A.3 Ring stiffness 28 A.4 Chemical resistance 28 Bibliography 29Page 3 EN 1519-1:1999 BSI 02-2

38、000 Foreword This European Standard has been prepared by Technical Committee CEN/TC 155, Plastics piping systems and ducting systems, the Secretariat of which is held by NNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by end

39、orsement, at the latest by January 2000, and conflicting national standards shall be withdrawn at the latest by July 2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgiu

40、m, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. This European Standard is one part of EN 1519 for plastics piping systems in the field of soil and waste discharge (low

41、 and high temperature) within the building structure made of polyethylene (PE), which consists of the following parts: Part 1: Specifications for pipes, fittings and the system Part 2: Guidance for the assessment of conformity. Following a decision of CEN/TC 155 after the CEN enquiry, this Part 1 is

42、 the result of merging of the following parts of the draft standard prEN 1519: Part 1: General (published for CEN enquiry as prEN 1519-1); Part 2: Pipes (published for CEN enquiry as prEN 1519-2); Part 3: Fittings (published for CEN enquiry as prEN 1519-3); Part 5: Fitness for purpose of the system

43、(published for CEN enquiry as prEN 1519-5). Part 6: Recommended practice for installation (published for CEN enquiry as prEN 1519-6) is intended to be included in a merged document for the recommended practice for installation of plastics piping systems in the field of soil and waste discharge (low

44、and high temperature) within the building structure. For this document the type of publication as European Prestandard (ENV) was approved by the CEN members. For Part 7: Assessment of conformity (published for CEN enquiry as prEN 1519-7) the type of publication as European Prestandard (ENV) 1519-2 “

45、Assessment of conformity“ was approved by the CEN members. This standard series is based on the results of the work undertaken in ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, which is a Technical Committee of the International Organization for Standardization (ISO). T

46、hey are supported by separate standards on test methods to which references are made throughout the standard. This part of EN 1566 includes the following annex: Annex A (informative): General characteristics of PE pipes and fittings.Page 4 EN 1519-1:1999 BSI 02-2000 1 Scope This European Standard sp

47、ecifies the requirements for pipes, fittings and the system of polyethylene (PE) solid- wall piping systems in the field of soil and waste discharge inside buildings (marked with “B”) and for both inside buildings and buried in ground within the building structure (marked with “BD”). NOTE 1: The app

48、lication area “inside buildings”, according to this standard, applies to the interior area of the building only. The application area “within the building structure” conforms to the requirements for “inside buildings” according to prEN 12056-1. It also specifies the test parameters for the test meth

49、ods referred to in this standard. This standard is applicable to PE pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following purposes: a) soil and waste discharge pipework for the conveyance of domestic waste waters (low and high temperature); b) ventilation pipework associated with a); c) rainwater pipework within the building structure. It applies to pipes and fittings, marked