1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 1652:1998 Incorpora
2、ting Corrigendum No. 1 The European Standard EN 1652:1997 has the status of a British Standard ICS 77.150.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Copper and copper alloys Plate, sheet, strip and circles for general purposesThis British Standard, having been prepared
3、 under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 April 1998 BSI 1998 ISBN 0 580 29464 1 BS EN 1652:1998 Amendments issued since publication Amd. No. Date Text affected 10198 Corr. No. 1 September 1998 Indicated
4、 by a sideline in the margin | | National foreword This British Standard is the English language version of EN 1652:1997. Together with BS EN 1653:1998 and BS EN 1654:1998 it supersedes BS 2870:1980 and BS 2875:1969 which are withdrawn. The UK participation in its preparation was entrusted by Techni
5、cal Committee NFE/34, Copper and copper alloys, to Subcommittee NFE/34/1, Wrought and unwrought copper and copper alloys, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change,
6、 and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or Europ
7、ean publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the neces
8、sary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu
9、r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1652:1997 E EUROPEAN STANDARD EN 1652 NORME EUROPE ENNE EUROPA ISCHE NORM December 1997 ICS 77.150.30 Descripto
10、rs: Copper, copper alloys, rolled products, metal plates, steel strips, blank, designation, chemical composition, mechanical properties, dimensions, dimensional tolerances, sampling, tests, verification English version Copper and copper alloys Plate, sheet, strip and circles for general purposes Cui
11、vre et alliages de cuivre Plaques, to les, bandes et disques pour usages ge ne raux Kupfer und Kupferlegierungen Platten, Bleche, Ba nder, Streifen und Ronden zur allgemeinen Verwendung This European Standard was approved by CEN on 6 November 1997. CEN members are bound to comply with the CEN/CENELE
12、C Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN
13、 member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN me
14、mbers are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN 1652:1997 BSI 1998 Foreword This European Standard has b
15、een prepared by Technical Committee CEN/TC 133, Copper and copper alloys, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 1998, and conflicting nation
16、al standards shall be withdrawn at the latest by June 1998. Within its programme of work, Technical Committee CEN/TC 133 requested CEN/TC 133/WG 2, Rolled flat products, to prepare the following standard: EN 1652, Copper and copper alloys Plate, sheet, strip and circles for general purposes This is
17、one of a series of European Standards for copper and copper alloy rolled flat products. Other products are, or will be, specified as follows: EN 1172, Copper and copper alloys Sheet and strip for building purposes EN 1653, Copper and copper alloys Plate, sheet and circles for boilers, pressure vesse
18、ls and hot water storage units EN 1654, Copper and copper alloys Strip for springs and connectors EN 1758, Copper and copper alloys Strip for lead frames Copper and copper alloys Copper plate, sheet and strip for electrical purposes (WI: 00133022) According to the CEN/CENELEC Internal Regulations, t
19、he national standards organizations of the following countries are bound to implement this European standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kin
20、gdom. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Definitions 3 3.1 plate 3 3.2 sheet 3 3.3 strip 3 3.4 circle 3 4 Designations 3 4.1 Material 3 4.2 Material condition 3 4.3 Product 4 5 Ordering information 5 Page 6 Requirements 5 6.1 Composition 5 6.2 Mechanical properties 5 6.3 G
21、rain size 5 6.4 Dimensions and tolerances 5 6.5 Edgewise curvature c 5 6.6 Surface condition 6 7 Sampling 6 7.1 General 6 7.2 Analysis 6 7.3 Tensile, hardness, grain size and technological tests 6 8 Test methods 6 8.1 Analysis 6 8.2 Tensile test 6 8.3 Hardness test 6 8.4 Estimation of average grain
22、size 6 8.5 Technological tests 6 8.6 Retests 6 8.7 Rounding of results 7 9 Declaration of conformity and inspection documentation 7 9.1 Declaration of conformity 7 9.2 Inspection documentation 7 10 Marking, packaging, labelling 7 Annex A (informative) Bibliography 38 Figure 1 Edgewise curvature c 6
23、Table 1 Composition of copper 7 Table 2 Composition of copper alloys 8 Table 3 Mechanical properties 11 Table 4 Tolerances on thickness of hot rolled products (plate, sheet, strip and circles) 35 Table 5 Tolerances on thickness of cold rolled products (sheet, strip and circles) 35 Table 6 Tolerances
24、 on width of cold rolled strip 36 Table 7 Tolerances on width of plate and sheet 36 Table 8 Tolerances on length of plate, sheet and strip cut to length for lengths up to 5 000 mm 36 Table 9 Squareness of cut plate and sheet 36 Table 10 Tolerances on diameter for circles 37 Table 11 Edgewise curvatu
25、re c 37Page 3 EN 1652:1997 BSI 1998 1 Scope This European Standard specifies the composition, property requirements and tolerances on dimensions and form for copper and copper alloy plate, sheet, strip and circles for general purposes. The sampling procedures, the methods of test for verification of
26、 conformity to the requirements of this standard, and the delivery conditions are also specified. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text
27、and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies
28、. EN 1655, Copper and copper alloys Declarations of conformity. prEN 1976, Copper and copper alloys Cast unwrought copper products. EN 10002-1, Metallic materials Tensile testing Part 1: Method of test (at ambient temperature). EN 10204, Metallic products Types of inspection documents. EN ISO 2624,
29、Copper and copper alloys Estimation of average grain size. (ISO 2624:1990) ISO 1811-2, Copper and copper alloys Selection and preparation of samples for chemical analysis Part 2: Sampling of wrought products and castings. ISO 6507-1, Metallic materials Hardness test Vickers test Part 1: HV 5 to HV 1
30、00. ISO 6507-2, Metallic materials Hardness test Vickers test Part 2: HV 0,2 to less than HV 5. ISO 7438, Metallic materials Bend test. ISO 7799, Metallic materials Sheet and strip 3 mm thick or less Reverse bend test. ISO 8490, Metallic materials Sheet and strip Modified Erichsen cupping test. NOTE
31、 Informative references to documents used in the preparation of this standard, and cited at the appropriate places in the text, are listed in a bibliography, see annex A. 3 Definitions For the purposes of this standard, the following definitions, based on ISO 197-3, apply: 3.1 plate flat rolled prod
32、uct of rectangular cross-section with uniform thickness greater than 10 mm 3.2 sheet flat rolled product of rectangular cross-section with uniform thickness from 0,2 mm up to and including 10 mm, supplied in straight lengths, usually with sheared or sawn edges. The thickness does not exceed one tent
33、h of the width 3.3 strip flat rolled product of rectangular cross-section with uniform thickness from 0,1 mm up to and including 5,0 mm manufactured in coil and supplied in as sheared coils, traverse wound coils or cut to length, usually with slit edges. The thickness does not exceed one tenth of th
34、e width 3.4 circle circular blank 4 Designations 4.1 Material 4.1.1 General The material is designated either by a symbol or a number (see Tables 1 and 2). 4.1.2 Symbol The material symbol designation is based on the designation system given in ISO 1190-1. NOTE Although material symbol designations
35、used in this standard might be the same as those in other standards using the designation system given in ISO 1190-1, the detailed composition requirements are not necessarily the same. 4.1.3 Number The material number designation is in accordance with the system given in EN 1412. 4.2 Material condi
36、tion For the purposes of this standard, the following designations, which are in accordance with the system given in EN 1173, apply for the material condition: R Material condition designated by the minimum value of tensile strength requirement for the product with mandatory tensile strength and elo
37、ngation requirements; H Material condition designated by the minimum value of hardness requirement for the product with mandatory hardness requirements; G Material condition designated by the mid-range value of grain size requirement for the product with mandatory grain size and hardness requirement
38、s. Exact conversion between material conditions designated R,H and G is not possible. Material condition is designated by only one of the above designations.Page 4 EN 1652:1997 BSI 1998 4.3 Product The product designation provides a standardized pattern of designation from which a rapid and unequivo
39、cal description of a product is conveyed in communication. It provides mutual comprehension at the international level with regard to products which meet the requirements of the relevant European Standard. The product designation is no substitute for the full content of the standard. The product des
40、ignation for products to this standard shall consist of: denomination (plate, sheet, strip or circle); number of this European Standard (EN 1652); material designation, either symbol or number (see Tables 1 and 2); material condition designation (see Table 3); nominal dimensions: plate: thickness3 w
41、idth3 length either “as manufactured” (M) or “fixed” (F) length (see example 1); sheet: thickness3 width3 length either “as manufactured” (M) or “fixed” (F) length; strip (in coils or on spools): thickness3 width; strip (cut to length): thickness3 width3 length either “as manufactured” (M) or “fixed
42、” (F) length; circles: thickness3 diameter (see example 2). The derivation of a product designation is shown for plate in example 1 and another typical product designation is shown in example 2. EXAMPLE 1: Plate conforming to this standard, in material designated either Cu-OF or CW008A, in material
43、condition H065, nominal thickness 14,25 mm, nominal width 350,5 mm, as manufactured length 1 200 mm, shall be designated as follows: EXAMPLE 2: Circle conforming to this standard, in material designated either CuNi12Zn24 or CW403J, in material condition R550, nominal thickness 1,115 mm, nominal diam
44、eter 345,5 mm, shall be designated as follows: Circle EN 1652 CuNi12Zn24 R550 1,1153 345,5 or Circle EN 1652 CW403J R550 1,1153 345,5Page 5 EN 1652:1997 BSI 1998 5 Ordering information In order to facilitate the enquiry, order and confirmation of order procedures between the purchaser and the suppli
45、er, the purchaser shall state on his enquiry and order the following information: a) quantity of product required: plate: number of pieces or mass; sheet: number of pieces or mass; strip (in coils or on spools): mass; strip (cut to length): mass or number of pieces; circle: number of pieces or mass;
46、 b) denomination (plate, sheet, strip or circle); c) number of this European standard (EN 1652); d) material designation (see Tables 1 and 2); e) material condition designation (see 4.2 and Table 3) if the choice is not to be left to the discretion of the supplier; f) nominal dimensions: plate, shee
47、t, strip (cut to length): thickness3 width3 length (either “as manufactured” or “fixed” length); strip (in coils or on spools): thickness3 width; circles: thickness3 diameter; g) coil size (strip) requirements: nominal inside diameter in millimetres and maximum outside diameter in millimetres and ei
48、ther maximum mass in kilograms or approximate specific coil weight (mass per width) in kilograms per millimetre; h) spool size (strip): type or dimensions. NOTE It is recommended that the product designation as described in 4.3, is used for items b) to f). In addition, the purchaser shall also state
49、 on the enquiry and order any of the following, if required: i) thickness tolerance required for hot rolled plate or circles with width or diameter over 1 500 mm (see Table 4); j) width tolerance required for plate or sheet with width over 1 250 mm (see Table 7); k) squareness requirement for cut plate or sheet with width over 1 250 mm (see Table 9); l) tolerance on diameter required for circles with diameter over 2 00
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1