1、BS EN1715-3:2008ICS 77.150.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAluminium andaluminium alloys Drawing stockPart 3: Specific requirements formechanical uses (excluding welding)This British Standardwas published under theauthority of the StandardsPoli
2、cy and StrategyCommittee on 31 2008 BSI 2008ISBN 978 0 580 57007 0Amendments/corrigenda issued since publicationDate CommentsBS EN 1715-3:2008National forewordThis British Standard is the UK implementation of . It supersedes BSEN 1715-3:1998 which is withdrawn.The UK participation in its preparation
3、 was entrusted to TechnicalCommittee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct ap
4、plication.Compliance with a British Standard cannot confer immunityfrom legal obligations.DecemberBS EN 1715-3:2008EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1715-3April 2008ICS 77.150.10 Supersedes EN 1715-3:1997 English VersionAluminium and aluminium alloys - Drawing stock - Part 3:Specific
5、 requirements for mechanical uses (excluding welding)Aluminium et alliages daluminium - Fil machine - Partie 3:Exigences spcifiques relatives aux applicationsmcaniques (soudage except)Aluminium und Aluminiumlegierungen - Vordraht - Teil 3:Besondere Anforderungen fr mechanische Anwendungen(ausgenomme
6、n Schweien)This European Standard was approved by CEN on 14 March 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographi
7、cal references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN m
8、ember into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
9、Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Bruss
10、els 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1715-3:2008: EBS EN 1715-3:2008EN 1715-3:2008 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Requirements.4 3.1 Chemical composition 4 3.2 Temper for delive
11、ry6 4 Product inspection and testing methods6 4.1 Chemical composition 6 4.2 Mechanical properties.6 5 Delivery documents and inspection documents6 6 Marking and packaging.7 BS EN 1715-3:2008EN 1715-3:2008 (E) 3 Foreword This document (EN 1715-3:2008) has been prepared by Technical Committee CEN/TC
12、132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn
13、 at the latest by October 2008. This document supersedes EN 1715-3:1997. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 4 “Wires and drawing stock“ to revise EN 1715-3:1997. Besides editorial adjustments in the text and update of normative references, the follow
14、ing changes have been made: Clause 3: amended; Table 1: values modified, alloy EN AW-5086 deleted, alloy EN AW-6056 added, new tempers for alloys EN AW-6060, EN AW-6061 and EN AW-6082 added EN 1715 comprises the following parts under the general title “Aluminium and aluminium alloys Drawing stock“:
15、Part 1: General requirements and technical conditions for inspection and delivery Part 2: Specific requirements for electrical applications Part 3: Specific requirements for mechanical uses (excluding welding) Part 4: Specific requirements for welding applications Part 5: Specific requirements for a
16、luminium food packaging1)Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms that it is its policy that in the case when a patentee re
17、fuses to grant licenses on standardised standard products under reasonable and not discriminatory conditions, then this product is removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to
18、implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzer
19、land and the United Kingdom. 1) Under preparation. BS EN 1715-3:2008EN 1715-3:2008 (E) 4 1 Scope This European Standard specifies specific requirements for drawing stock of aluminium and aluminium alloys for general mechanical uses (excluding welding). The general requirements and technical conditio
20、ns for inspection and delivery are specified in EN 1715-1. This European Standard does not apply to drawn wire. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated referenc
21、es, the latest edition of the referenced document (including any amendments) applies. EN 515, Aluminium and aluminium alloys Wrought products Temper designations EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical composition and form of produc
22、ts EN 1715-1, Aluminium and aluminium alloys Drawing stock Part 1: General requirements and technical conditions for inspection and delivery 3 Requirements 3.1 Chemical composition Aluminium and aluminium alloys used commonly for mechanical uses (excluding welding) are given in Table 1. Their chemic
23、al composition shall be in accordance with EN 573-3. The elements determined and reported in the certificate of mass and analysis shall be : Si, Fe, Cu, Mn, Mg, Cr, Ni, Zn, Ti, Ga and V. If other elements (e.g. Pb, Bi, Zr.) are specified in EN 573-3, they shall be determined and reported in the cert
24、ificate of mass and analysis. BS EN 1715-3:2008EN 1715-3:2008 (E) 5 Table 1 Main alloys for mechanical purposes - Tempers for delivery Typical tensile strength values Alloy designation Temper Tensile strength typical range Rm MPa Continuously cast rod Hot rolled and extruded rod 1 000 Serie EN AW-10
25、98 Al 99,98 F 75 to 85 75 to 85 EN AW-1080A Al 99,8(A) F80 to 110 80 to 110 O 60 to 75 60 to 75 EN AW-1070A Al 99,7 F 80 to 110 80 to 110 O 60 to 75 60 to 75 EN AW-1050A Al 99,5 F 80 to 130 80 to 130 O 60 to 80 60 to 80 2 000 Serie EN AW-2011 Al Cu6BiPb F 170 to 230 170 to 400 O3 110 to 170 110 to 1
26、70 EN AW-2014A Al Cu4 SiMg(A) F 200 to 260 200 to 400 O/O3 150 to 220 150 to 220 EN AW-2017A Al Cu4 MgSi(A) F 200 to 260 200 to 400 O/O3 150 to 220 150 to 220 EN AW-2117 Al Cu2,5Mg F 170 to 230 170 to 360 O/O3 140 to 200 140 to 200 EN AW-2024 Al Cu4Mg1 F 200 to 280 200 to 440 O/O3 180 to 240 180 to
27、240 3 000 Serie EN AW-3003 Al Mn1Cu F 120 to 220 120 to 220 O3 95 to 120 95 to 120 EN AW-3103 Al Mn1 F 120 to 220 120 to 220 O3 95 to 115 95 to 115 5 000 Serie EN AW-5051A Al Mg2(B) F 170 to 230 EN AW-5251 Al Mg2Mn0,3 F 170 to 230 EN AW-5052 Al Mg2,5 F 180 to 260 EN AW-5154A Al Mg3,5(A) F 210 to 280
28、 O3 210 to 250 EN AW-5754 Al Mg3 F 200 to 260 O3 200 to 250 EN AW-5019 Al Mg5 F 250 to 320 O/O3 250 to 310 6 000 Serie EN AW-6056 Al Si1MgCuMn F 160 to 230 O3 140 to 180 T4 300 to 380 EN AW-6060 Al MgSi F 120 to 190 T4 155 to 210 EN AW-6061 Al Mg1SiCu F 120 to 200 O3 90 to 140 T4 220 to 280 EN AW-60
29、63 Al Mg0,7Si T4 160 to 220 EN AW-6082 Al Si1MgMn F 130 to 220 O3 100 to 150 T4 230 to 290 7 000 Serie EN AW-7075 Al Zn5,5MgCu O/O3 180 to 290 BS EN 1715-3:2008EN 1715-3:2008 (E) 6 3.2 Temper for delivery The variety of application of drawn wire made from drawing stock of aluminium and aluminium all
30、oys used for mechanical applications requires a precise definition of the temper for delivery which is liable to exert a significant influence on the ability to process and on the final characteristics. Tempers shall be indicated in accordance with EN 515. The usual tempers for drawing stock covered
31、 by this European Standard are: F: as fabricated; O: annealed; O3: homogenised; T4: solution heat treated and naturally aged. These tempers are listed in Table 1 with typical ranges of mechanical characteristics (tensile strength). If no temper is specified when ordering, the delivered temper shall
32、be F. Other tempers shall be agreed between manufacturer and purchaser. 4 Product inspection and testing methods 4.1 Chemical composition The chemical composition shall be checked for each cast delivered in accordance with EN 1715-1. 4.2 Mechanical properties The mechanical properties shall be at le
33、ast measured once per coil in accordance with EN 1715-1. Other sampling frequencies shall be agreed between manufacturer and purchaser. 5 Delivery documents and inspection documents A certificate of mass and analysis shall be provided in accordance with EN 1715-1. In addition, a test report in accor
34、dance with EN 1715-1 shall be delivered for each cast in a consignment with reference to the order, and giving the following information: identification of the alloy; temper; diameter; list of coil identification numbers; results of test for mechanical properties; date of manufacture; BS EN 1715-3:2
35、008EN 1715-3:2008 (E) 7 date of heat treatment, if any; net mass. NOTE Other inspection documents can be defined between manufacturer and purchaser in accordance with EN 1715-1. 6 Marking and packaging Marking and packaging shall be carried out in accordance with EN 1715-1. BS EN1715-3:2008BSI Group
36、Headquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorpor
37、ated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone findin
38、g an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLU
39、S which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly usi
40、ng a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of inform
41、ation on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20
42、 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Informat
43、ion regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international st
44、andardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not precl
45、ude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email:
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1