BS EN 210-2000 Steel drums Non-removable head (tight head) drums with a minimum total capacity of 216 5 l《钢桶 最小总容积为216 5 l的不可拆卸盖(密封式)钢桶》.pdf

1、 STD-BSI BS EN 210-ENGL 2000 m Lb24bb9 O34499 b5T m BRITISH STANDARD Steel drums - Non-removable head (tight head) drums with a minimum total capacity of 216,5 1 The European Standard EN 2101999 has the status of a British Standard ICs 55.140 35 EN !102000 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS

2、 PERMiED BY COPYRIGHT LAW Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STDeBSI BS EN 210-ENGL 2000 m Lb24bb9 0834500 LTL m BS EN 2102000 been prepared under the direction of t

3、he Consumer Products and Sewices Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 March Zoo0 Amd. No. O BSI 03-2000 ISBN O 580 35748 1 National foreword Date Comments This British Standard is the official English language version of EN 210199

4、9. It supersedes BS 8141: 1987 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee PKWE, Primary packagmg to Subcommittee PKW/2/4, Drums, which has the responsibility to: - aid enquirem to understand the text; - present to the responsible European committ

5、ee any enquiries on the - monitor related international and European developments and promulgate interpretation, or proposals for change, and keep the UK interests informed; them in the UK A list of organizations represented on this subcommittee can be obtained on request to its secrem. Cross-refere

6、nces The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index“, or by using the “Find“ facility of the BSI Standards Electronic Catalo

7、gue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document compr

8、ises a front cover, an inside front cover, the EN title page, pages 2 to 11 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo repro

9、duction or networking permitted without license from IHS-,-,- STD-BSI BS EN 230-ENGL 2000 - Lb24bb9 0834503 036 W EUROPEAN STANDARD EN 210 NORME EUROPENNE EUROPISCHE NORM December 1999 ICs 55.140 Supersedes EN 210:1986 English version Steel drums - Non-removable head (tight head) drums with a minimu

10、m total capacity of 216,5 I Fts en acier - Fts ouverture partielle dune capacit totale de 216,5 I minimum Stahlfsser - Spundfsser mit einem minimum Gesamtvolumen von mindestens 216,5 I This European Standard was approved by CEN on 23 October 1999. CEN members are bound to comply with the CENICENELEC

11、 Internal Regulations which stipulate the conditions for giving this Europein Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning sJch national standards may be obtained on application to the Central Secretariat or to any CEN

12、member. This European Standard exists in three official versions (English, French, German). A version in any other language made by traislation under the responsibility of a CEN member into its own language and notified to the Centrai Secretariat has the same status as he oficial versions. CEN membe

13、rs are the national standards bodies of Austria. Belgium, Czech Republic, Denmark. Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEEN DE NORMALISATI

14、ON EUROPISCHES KOMITEE FR NORMUNG Central Secretariat: rue de Stassart, 36 8-1050 Brussels O 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 210:1999 E Copyright European Committee for Standardization Provided by IHS under lic

15、ense with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- STDmBSI ES EN 210-ENGL 2000 M Lb24bb9 083Y502 T34 Page 2 EN 210:1999 Contents Page Foreword - 3 1 . Scope 4 2 . Normative references . 4 Terms and definitions 4 Dimensions - 5 3 . 4 . 5 . Material 5 6 .

16、Construction - 5 7 . Finish . ._ . 6 8 . Draining 6 9 . Designation . 6 Annex A (normative) Capacity measurement method for non-removable head (tight head) steel drums . 8 Annex B (normative) Draining test method for non-removable head (tight head) steel drums 10 OBSI 03-2000 Copyright European Comm

17、ittee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- STD-BSI BS EN 210-ENGL 2000 W 1b24bb9 0834503 900 D Page 3 EN 21 O: 1999 Foreword This European Standard has been prepared by Technical Committee CENTTC

18、 261, Packaging, the Secretariat of which is held by AFNOR This European Standard replaces EN 21 O: 1986. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2000, and conflicting national standa

19、rds shall be withdrawn at the latest by June 2000. According to the CENICENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, I

20、reland, Italy, Luxembourg, Netherlands, Noway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. This standard cancels and replaces EN 210:1986 in order to include drums with special dimensions for optimal loading of freight containers and drums with differently shaped tops for optimal dr

21、aining. This standard is one of a series of standards on steel drums of 17 I to 230 I and closures. Efficient packaging is of great importance for the distribution and the protection of goods. Insufficient or inappropriate packaging can lead to damage or wastage of the contents of the package. OBSI

22、03-2000 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD-BSI BS EN 210-ENGL 2000 = 3624667 0834504 847 - Page 4 EN 21 O: 1999 I. Scope This European Standard specifies the cha

23、racteristics and dimensions of non-removable head (tight head) drums, manufactured from steel sheet, having a minimum total capacity of 216,5 I. 2. Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references a

24、re cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest

25、edition of the publication referred to applies. EN 10111:1998 EN 1 O1 30+A1: 1998 EN 10131:1991 prEN 12928: 1999 EN IS0 90-2: 1999 IS0 228-1 11 994 IS0 668: 1995 Continuously hot-rolled low -carbon steel sheet and strip for cold forming - Technical delivery conditions. Cold rolled low carbon steel f

26、lat products for cold forming - Technical delivery conditions. Cold rolled uncoated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape. Inserted flange type closure systems for steel drums with a total capacity of 17 I to 230 I. Light gauge m

27、etal containers - Definitions and determination of dimensions and capacities - Part 2: General use containers (IS0 90- 2:1997). Pipe threads where pressure-tight joints are not made on the threads - Part 1 : Dimensions, tolerances and designation. Series 1 freight containers - Classification, dimens

28、ions and ratings. 3. Terms and definitions For the purposes of this standard, the following terms and definitions apply. 3.1 non-removable head (tight head) drum (TH) cylindrical packaging made of steel, the ends of which are permanently fixed to the body, with openings for filling, emptying and ven

29、ting in the head 3.2 nominal capacity (NC) capacity in litres which, by convention, is used to represent a class of drums of similar brimful capacities OBSI 03-2000 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking perm

30、itted without license from IHS-,-,-Page 5 EN 21 O: 1999 3.3 brimful capacity (BC) volume of water in litres held by the drum when filled through the filling orifice to the point of overflowing NOTE Annex A specifies the method for measuring brimful capacity. 3.4 total capacity (TC) volume of water i

31、n litres held by the drum when filled completely, .e. following the removal of any air trapped in the drum NOTE Annex A specifies the method for measuring total capacity. 4. Dimensions The dimensions of non-removable (tight head) drums with a minimum total capacity of 216,5 I shall be as shown in Fi

32、gure 1. In addition the steel thickness shall be between 0,6 mm and I ,5 mm, with tolerances as specified in EN 1 O1 31 : 1991 (normal tolerances). Manufacturing tolerances on overall height (h) shall be 13 mm. 5. Material The body and ends of the drums shall be made of steel DC O1 in accordance wit

33、h EN 10130+A1:1998, hot-rolled steel DDI 1 in accordance with EN 101 11 :1998, or steel of a higher strength. Closure flanges shall be manufactured from metal, and closure plugs from metal or plastics material as specified in prEN 12928:1999. 6. Construction 6.1 The longitudinal seam of the body sha

34、ll be welded. 6.2 The body and ends shall be combined by round or triple seaming or other joining methods (e.9. welding). 6.3 The closures shall be in accordance with prEN 12928:1999 and shall be positioned in the top end of the drum, diametrically opposed, as indicated in Figure I. The nominal pitc

35、h diameter and the pitch of the closures shall be as defined in IS0 228-1:1994, for threads G 314 and G2. The insertion of the closure with the G2 thread shall be such that its centre line is as close as possible to the vertical. The metal or plastics plugs shall be fitted with washers of suitable m

36、aterial compatible with the contents of the drum. NOTE 1 In addition to the two rolling hoops (beads) as shown in Figure 1, the drum body may be reinforced with corrugations leaving a free space of at least 1 15 mm from the seams. NOTE 2 Instead of a convex top, as shown in Figure I, the drum can be

37、 fitted with a differently shaped top for optimal draining in an upside down position. OBSI 03-2000 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD=BSI BS EN 210-ENGL 2000 Lb

38、2rlbb9 063450b bLT M Page 6 EN 21 O: I999 7. Finish The nature of the internal and external finish shall be appropriate to the physical and chemical requirements of their intended use. NOTE The nature of the internal and external finish should be agreed between the purchaser and the manufacturer. 8.

39、 Draining 8.1 The drum shall be designed so as to minimize the residual volume of the liquid left in the drum after drainage. The residue shall be not more than 100 ml when tested according to B.3 (procedure A) 8.2 The residue obtained when the drum is tested according to B.4 (procedure 6) is more d

40、ependent on the area and condition of the internal surface of the drum than procedure A and therefore may be in excess of that for procedure A. NOTE The maximum permitted figure should be agreed between the purchaser and the supplier. 9. Designation A non-removable head (tight head) drum (TH) manufa

41、ctured in accordance with EN 210 with a minimum total capacity of 216,5 I shall be designated: Steel drum TH EN 210 TC-216,5 I. NOTE Where the drums are intended to be used for the transport of dangerous goods, attention is drawn to the regulatory requirements which govern the transport of those goo

42、ds in the countries concerned. In Europe, depending upon the mode of transport, this means meeting the requirements of: European Agreement Concerning the International Carriage of Dangerous Goods by Road (ADR); Regulations concerning the International Carriage of Dangerous Goods by Rail (RID); Techn

43、ical Instructions for the Safe Transport of Dangerous Goods by Air, Document 92844Nl905 published by the Council of the International Civil Aviation Organization (ICAO); The International Maritime Dangerous Goods Code (IMDG-CODE) published by the International Maritime Organization (IMO). OBSI 03-20

44、00 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STDaBSI BS EN 210-ENGL ZOO0 I 1b24bb9 0834507 556 = Page 7 EN 210:1999 Dimensions in millimetres Clearance from topside 2 minim

45、um Detail A “ I +1 d int.O 571,5 -35 Detail B 14 di8596 max. I 1 0585 max.d n r) o 03 03 L Clearance from floor 4 minimum - I dz 0589 max. I I 0585 max.d I a The complete closures (plugs and capseals) shall not protrude above the top seam. The maximum overall height shall be 887 mm for drums having

46、a concave formed top. Diameter l and diameter 2 shall be 596 mm maximum and 589 mm maximum respectively on drums for general purpose. Diameter dl and diameter 2 shall be 585 mm maximum on drums for freight containers according to IS0 668: 1995. Figure 1 - Non-removable (tight head) drum with a minim

47、um total capacity of 216,5 I OBSI 03-2000 - Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD-BSI BS EN 210-ENGL 2000 m 1624669 0834508 492 W Page 8 EN 210:1999 Annex A (normat

48、ive) Capacity measurement method for non-removable head (tight head) steel drums A. i. Principle The capacity is determined by a gravimetric method, .e. by the measurement of the mass of water in the filled drum and its conversion to a capacity. A correction factor can be applied according to Table

49、A.1, but only if the weighing scale used is of a higher precision than the correction. Table A.1 - Correction factorsa I Water temperature I Correction factor (F) I A. 2. Apparatus A.2.1 Weighing scale, with an accuracy of at least O,l% of the weight being measured. A. 3. Procedure for determination of total capacity A.3.1 Drill a hole of diameter 5 mm to IO mm for venting at the highest p