BS EN 2155-12-1997 Specification for test methods for transparent materials for aircraft glazing - Determination of linear thermal expansion《飞机舷窗玻璃用透明材料试验方法规范 线性热膨胀测定》.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS EN 2155-12:1997 Test methods for transparent materials for aircraft glazing Part 12: Determination of linear thermal expansion The European Standard EN 2155-12:1997 has the status of a British Standard ICS 49.025.99; 49.045BSEN2155-12:1997 This British Standard,

2、having been prepared under the directionof the Engineering SectorBoard, was published underthe authority of the Standards Board and comes into effect on 15 November 1997 BSI 04-2000 ISBN 0 580 28134 5 National foreword This British Standard is the English language version of EN 2155-12:1997. The UK

3、participation in its preparation was entrusted to Technical Committee ACE/62, Aerospace structural transparencies and non-reinforced plastics, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or

4、proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement i

5、nternational or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. NOTEUnder the AECMA part numbering syst

6、em, normative references to the Parts of AECMA-originated European Standards may appear in clause 2 in the form of a three-digit number e.g. -001 where the BSI and CEN systems would use the form -1. It can be assumed that, wherever referenced, the three-digit and single digit forms can be used inter

7、changeably. For the purposes of part-marking of components produced in accordance with this standard, the three-digit form should be used. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applicati

8、on. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 5 and a back cover. This standard has been updated (see copyright date) and ma

9、y have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN2155-12:1997 BSI 04-2000 i Contents Page National foreword Inside front cover Foreword 2 Text of EN 2155-12 3ii blankEUROPEAN STA

10、NDARD NORME EUROPENNE EUROPISCHE NORM EN 2155-12 July 1997 ICS 49.025.40 Descriptors: Aircraft industry, glazing, materials, transparency, plastics, tests, determination, thermal properties, thermal expansion English version Aerospace series Test methods for transparent materials for aircraft glazin

11、g Part 12: Determination of linear thermal expansion Srie arospatiale Mthodes dessais pour matriaux transparents pour vitrages aronautiques Partie 12: Dtermination de la dilatation thermique linaire Luft- und Raumfahrt Prfverfahren fr transparente Werkstoffe zur Verglasung von Luftfahrzeugen Teil 12

12、: Bestimmung der linearen Wrmeausdehnung This European Standard was approved by CEN on 1997-03-27. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-t

13、o-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under

14、the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembo

15、urg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by

16、any means reserved worldwide for CEN national Members. Ref. No. EN 2155-12:1997 EEN2155-12:1997 BSI 04-2000 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this A

17、ssociation, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by end

18、orsement, at the latest by January 1998, and conflicting national standards shall be withdrawn at the latest by January 1998. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Bel

19、gium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the UnitedKingdom. Contents Page Foreword 2 1 Scope 3 2 Definition 3 3 Apparatus 3 4 Specimens 3 5 Conditioning 3 6 Procedure 3 7 Express

20、ion of results 4 8 Test report 4 Figure 1 Quartz-tube dilatometer 5EN2155-12:1997 BSI 04-2000 3 1 Scope This standard specifies the method to determine the reversible linear thermal expansion of plastics with exclusion of changes in length due to accidental factors such as changes in moisture conten

21、t, degree of polymerization and stress release. Since it will not be possible to exclude all these accidental factors, the method can be expected to give only approximate values. 2 Definition For the purposes of this standard, the following definition applies: Linear thermal expansion is defined as

22、the change in length of a material in relation to unit length for a variation in temperature of 1 C. 3 Apparatus 3.1 Dilatometer A simple fused-quartz tube dilatometer is shown in Figure 1. Any generally accepted method of measuring thermal expansion may be used which will be accurate to within 10%.

23、 The accuracy of the device which measures the expansion shall be such that it measures the change in length over the temperature interval under consideration within 2%. This device shall not exert a stress of more than 50 kPa on this specimen which shall not be distorted or indented. 3.2 Scale or c

24、aliper The scale or caliper shall be capable of measuring the test length of the specimen with an accuracy of 0,5%. 3.3 Temperature bath The temperature of the specimen shall preferably be controlled by the use of a liquid bath. The bath shall be arranged in such a way that uniform temperature throu

25、ghout the specimen is secured. Means shall be provided for stirring the bath and for controlling its temperature within 0,2 C of the temperatures used. 4 Specimens 4.1 Preparation Specimens shall be cut or shaped, from sheet. The ends of the specimen shall be cut perpendicular to the axis of the spe

26、cimen. They shall be protected by means of thin steel plates cemented to them. 4.2 Dimensions For the apparatus shown in Figure 1, specimens can be round or square and shall fit easily into the outer tube without excessive play. The length of the specimen may be 50 mm to 100 mm but its length is gov

27、erned to some extent by the sensitivity of the dial gauge, the expected expansion and the desired accuracy. 5 Conditioning The specimen shall be conditioned at (23 2) C, (50 5)% relative humidity for at least 48 h prior to measurement of the test length of the specimen under these conditions. 6 Proc

28、edure The temperature range over which the coefficient of thermal expansion is to be measured shall be chosen so that no transitional regions are included. The limits of the range shall be agreed between purchaser and manufacturer. 6.1 Low temperature Mount the specimen in the apparatus and maintain

29、 the temperature of the bath at the lowest temperature at which measurements are required until the temperature of the specimen reaches the temperature of the bath. The time necessary shall be determined by preliminary measurements of temperature inside a similar specimen. Record the reading of the

30、dial gauge or other device indicating change in length. 6.2 High temperature Repeat the foregoing operations at the highest temperature at which measurements are required. 6.3 Check determination Repeat the operations described in 6.1 and 6.2. If the changes in length caused by heating and cooling d

31、o not agree within 10% of their average, the cause of this discrepancy shall be investigated and if possible, eliminated (see 6.5). Otherwise the observations shall be reported, see 8.3. 6.4 Constant temperature bath Where the construction of the apparatus permits, it may be more convenient to alter

32、nately use two baths at the required temperatures. Care shall be taken not to disturb the apparatus during exchange. The use of two baths is preferred because it will reduce the time required to bring the specimen to the desired temperature. The test in general shall be conducted in as short a time

33、as possible to avoid changes in physical properties during long exposure to high and low temperatures.EN2155-12:1997 4 BSI 04-2000 6.5 Transition temperature The coefficient of thermal expansion of some materials is known to change rather abruptly at a certain temperature. To find this temperature,

34、it is necessary to measure the coefficient of thermal expansion in narrow temperature limits, or to observe the rate of expansion during a steady rise in temperature of the specimen. Once such a transition point has been found, a separate coefficient of expansion for a temperature range below and ab

35、ove the transition point shall be determined. 7 Expression of results The average coefficient of thermal expansion shall be calculated from the formula: Coefficient of linear thermal expansion = where: 8 Test report It shall include: 8.1 Temperatures between which the coefficient of thermal expansio

36、n has been computed. 8.2 Average coefficient of linear thermal expansion per C 8.3 Complete description of any unusual behaviour such as, for instance, a difference of more than 10% in measured values of expansion and contraction %L is the average of changes in length due to heating or cooling; L is

37、 the test length of specimens immediately after the conditioning stage (%L and L being in the same units); T is the temperature difference in C over which the change in length has been measured. %L L T -EN2155-12:1997 BSI 04-2000 5 Figure 1 Quartz-tube dilatometerBS EN 2155-12:1997 BSI 389 Chiswick

38、High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendm

39、ent or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would

40、 inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of stan

41、dards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been publis

42、hed as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available whi

43、ch give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits

44、 contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988

45、no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such

46、 as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.