1、BRITISH STANDARD AEROSPACE SERIESBS EN 2243-1:2005Non-metallic materials Structural adhesives Test method Part 1: Single lap shearThe European Standard EN 2243-1:2005 has the status of a British StandardICS 49.025.50g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g
2、54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Fri Apr 14 02:34:58 BST 2006, Uncontrolled Copy, (c) BSIBS EN 2243-1:2005This British Standard was published under the authority of the Standards Policy an
3、d Strategy Committee on 23 January 2006 BSI 23 January 2006ISBN 0 580 47230 2National forewordThis British Standard is the official English language version of EN 2243-1:2005. The UK participation in its preparation was entrusted by Technical Committee ACE/65, Non-metallic materials for aerospace pu
4、rposes, to Subcommittee ACE/65/-/3, Structural adhesives, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in
5、this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a c
6、ontract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposal
7、s for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and a back cover.The BSI copyright notice displayed in thi
8、s document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsLicensed Copy: Wang Bin, na, Fri Apr 14 02:34:58 BST 2006, Uncontrolled Copy, (c) BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2243-1November 2005ICS 49.025.50English VersionAerosp
9、ace series - Non-metallic materials - Structural adhesives- Test method - Part 1: Single lap shearSrie arospatiale - Matriaux non-mtalliques - Systmedadhsifs structuraux - Mthodes dessai - Partie 1 :Essais de cisaillement dun joint recouvrement simpleLuft- und Raumfahrt - Nichtmetallische Werkstoffe
10、 -Strukturelle Klebstoffsysteme - Prfverfahren - Teil 1:Bestimmung der Bindefestigkeit von einschnittigberlappten Klebungen im ZugversuchThis European Standard was approved by CEN on 30 September 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the condi
11、tions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three off
12、icial versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Be
13、lgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMI
14、T EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2243-1:2005: ELicensed Copy: Wang Bin, na, Fri Apr 14 02:34:58 BST 20
15、06, Uncontrolled Copy, (c) BSI2 Contents Page Foreword 3 1 Scope .4 2 Normative references .4 3 Test samples .4 4 Surface preparation 5 5 Bonding .5 6 Storage of test samples after bonding 5 7 Cutting and preparation of test pieces5 8 Test conditions .6 9 Method of test .6 10 Calculation of results6
16、 11 Test report .7 EN 2243-1:2005Licensed Copy: Wang Bin, na, Fri Apr 14 02:34:58 BST 2006, Uncontrolled Copy, (c) BSI3 Foreword This European Standard (EN 2243-1:2005) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes
17、carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, ei
18、ther by publication of an identical text or by endorsement, at the latest by May 2006, and conflicting national standards shall be withdrawn at the latest by May 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CEN
19、ELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Eston
20、ia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 2243-1:2005Licensed Copy: Wang Bin, na, Fri Apr 14 02:34:58 BST 2006, Uncontr
21、olled Copy, (c) BSI4 1 Scope The objective of this standard is to establish the test methods for defining the strength of suitable structural adhesives in metal to metal single lap shear, at ambient and other temperatures. 2 Normative references The following referenced documents are indispensable f
22、or the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2087, Aerospace series Aluminium alloy AL-P2014A T6 or T62 Clad sheet and strip 0,4 mm a 6 mm.1) EN
23、2088, Aerospace series Aluminium alloy AL-P2014A T4 or T42 Clad sheet and strip 0,4 mm a 6 mm. 1)EN 2090, Aerospace series Aluminium alloy AL-P2024- T3 Clad sheet and strip 0,3 mm a 6 mm.1)EN 2092, Aerospace series Aluminium alloy AL-P7075- T6 or T62 Clad sheet and strip 0,4 mm a 6 mm. EN 2334, Aero
24、space series Chromic-sulphuric acid pickle of aluminium and aluminium alloys. EN 2497, Aerospace series Dry abrasive blasting of titanium and titanium alloys. EN 2540, Aerospace series Steel FE-PM3902 (X7CrNiAl17-7) Air melted Solution treated and precipitation hardened Sheet and strip a 6 mm 1 240
25、MPa Rm 1 450 MPa.1)EN 2517, Titanium alloy TI-P63 Annealed Sheets, strips and plates a 100 mm Aerospace series. 2)EN 3456, Aerospace series Titanium alloy TI-P64001 Annealed Sheet and strip, hot rolled a 6 mm.1)EN 3464, Aerospace series Titanium alloy TI-P64001 Annealed Plate 6 mm a 100 mm.1)3 Test
26、samples 3.1 Shape and dimensions The shape and dimensions of the test pieces and the panel out of which the pieces shall be cut, shall be as given in Figure 1. 3.2 Sheet material (general) Aluminium alloys for use to 150 C, see EN 2088 and EN 2090. 1) Published as AECMA Prestandard at the date of pu
27、blication of this standard. 2) Published as AECMA Standard at the date of publication of this standard. Inactive for new design. EN 2243-1:2005Licensed Copy: Wang Bin, na, Fri Apr 14 02:34:58 BST 2006, Uncontrolled Copy, (c) BSI5 3.3 Sheet material (special) For adhesives having a shear strength hig
28、her than approximately 45 MPa, aluminium alloys for use up to 150 C can be used instead of the materials given in 3.2, see EN 2092 and EN 2087. 3.4 Sheet material (for test temperature above 150 C) 3.4.1 Corrosion resisting steel FE-PM3902 See EN 2540. 3.4.2 Titanium alloy TI-P63 or TI-P64001 See EN
29、 2517 or EN 3456 and EN 3464. 4 Surface preparation The surface preparation prior to bonding shall conform to EN 2334 and EN 2497. 5 Bonding The application of the adhesive system (adhesive and primer) as applicable and curing shall be carried out according to the instruction of the adhesive manufac
30、turer or the material standard. 6 Storage of test samples after bonding After curing the sample made with elevated temperature curing adhesives shall be exposed and/or after a storage period of 16 h under the conditions as given below (unless otherwise specified by the adhesive manufacturer). The sa
31、mple for room temperature curing adhesives not exposed and/or tested immediately after curing shall also be stored as given below (unless otherwise specified by the adhesive manufacturer). Storage conditions: room temperature: (23 2) C relative humidity: (50 5 ) % 7 Cutting and preparation of test p
32、ieces The test sample shall be carefully cut into pieces with a suitable tool such as a band saw. The setting and spacing of the teeth and the operational speed shall be such that the frictional heating of the bond will be kept to a minimum. The cutting shall be straight and parallel. For cutting sh
33、all be straight and parallel. For cutting corrosion resisting steel and titanium alloy test samples a suitable cutting fluid may be used. EN 2243-1:2005Licensed Copy: Wang Bin, na, Fri Apr 14 02:34:58 BST 2006, Uncontrolled Copy, (c) BSI6 8 Test conditions 8.1 The test shall be carried out at the te
34、mperatures stated in the relevant material standard. When the test temperature is different from the ambient temperature then the rate of the heating shall be between 6 C to 10 C per minute. The rate of cooling need not be controlled. The application of load for all tests at temperature other than a
35、mbient shall be made immediately after the specimen has been held at the specified test range for 10 min unless a longer term of exposure is required. 8.2 For all test temperature excluding room temperature (23 2) C, temperature control of the test pieces shall be carried out with the aid of a therm
36、ocouple to ensure the accuracy of testing temperature and reproducibility of data. The junction of the thermocouple shall be firmly attached to the test piece in immediate contact with the metal in the position shown in Figure 2 and shielded from the heat source. 8.3 The number of test pieces for ea
37、ch determination shall be as required by the material standard. 8.4 Each test piece shall be identified in order to establish the panel from which it was cut. 9 Method of test 9.1 Tensile testing machine 9.1.1 An approved tensile testing machine shall be used. The failing load of the test piece shal
38、l be within 10 % to 90 % of the upper limit of the selected loading range of the machine. 9.1.2 The test loads shall be recorded within an accuracy of 1 %. 9.2 Method of fixing The ends of the specimen shall be gripped tightly with a good fit in the jaws of the testing machine. The jaws and the test
39、 pieces shall be aligned such that the jaws are directly opposite each other and in such a position that an imaginary straight line will pass through the centre of the bonded area and through the point of fixing. The specimen shall be gripped (50 5) mm from each edge of the lap joint (see also Figur
40、e 3). 9.3 Speed rate of loading The rate of loading shall be 2 800 N/min to 5 000 N/min. 10 Calculation of results The test results to be reported shall be calculated as follows: WLFR= EN 2243-1:2005Licensed Copy: Wang Bin, na, Fri Apr 14 02:34:58 BST 2006, Uncontrolled Copy, (c) BSI7 where R shear
41、strength, in MPa F failing load, in Newtons L length of overload, in millimetres W width of overlap, in millimetres The dimensions L and W are to be measured before loading with an accuracy of 0,1 mm. 11 Test report The test report shall include the following information: Complete identification of
42、the adhesive system including the type, suppliers code numbers, date of manufacture, batch number, material standard, etc. Complete identification of the metal used, including actual proof stress in the direction of loading used for the adhesive test. Detailed information about the pre-treatment of
43、the metal prior to bonding. Application and bonding conditions including autoclave or press bondline pressure, heat-up rate, cure time and temperature, etc. The number of test pieces used. Time exposure conditions and test temperature. The type of testing machine and speed of load. Information about
44、 individual test pieces including actual dimensions and overload, sheet thickness, load at failure and shear strength. The nature of the failure, including the average estimated percentage of failure in cohesion and/or adhesion both of adhesive and possible adhesive primer. The average, maximum and
45、minimum shear strength values of the test series. Any deviations from this test method shall be described in detail. EN 2243-1:2005Licensed Copy: Wang Bin, na, Fri Apr 14 02:34:58 BST 2006, Uncontrolled Copy, (c) BSI8 Dimensions in millimetres Key 1 1,6 for aluminium alloy 1,2 for corrosion resistin
46、g steel and titanium alloy 2 Grip 3 Discard 4 Direction of rolling 5 Tooling holes as required Figure 1 The width of separate panels prior to bonding, given as approx. 100, depends upon grip length required for the particular testing machine. The tooling holes should be approx. 2 mm to 4 mm. The dir
47、ection of rolling of the sheet material shall be parallel to the longitudinal axis of the test pieces. All the edges of the panels which will be within the bonded joint shall be smooth, without burrs and at right angles to the faces before surface treatment. EN 2243-1:2005Licensed Copy: Wang Bin, na
48、, Fri Apr 14 02:34:58 BST 2006, Uncontrolled Copy, (c) BSI9 Dimensions in millimetres Figure 2 Thermocouple junction placed on metal within shaded portion of bonded area (6 7) mm. Dimensions in millimetres Figure 3 EN 2243-1:2005Licensed Copy: Wang Bin, na, Fri Apr 14 02:34:58 BST 2006, Uncontrolled
49、 Copy, (c) BSIBS EN 2243-1:2005BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparingBritish Standards. It presents the UK view on standards in Europe international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the la
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1