1、BRITISH STANDARDBS EN 2335:2005Aerospace series Bearings, spherical plain in corrosion resisting steel without assembly slot Dimensions and loadsThe European Standard EN 2335:2005 has the status of a British StandardICS 49.035g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53
2、g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Wed Mar 21 06:59:01 GMT+00:00 2007, Uncontrolled Copy, (c) BSIBS EN 2335:2005This British Standard was published under the authority of the Stand
3、ards Policy and Strategy Committee on 29 December 2006 BSI 2006ISBN 0 580 49854 9National forewordThis British Standard was published by BSI. It is the UK implementation of EN 2335:2005. It supersedes BS EN 2335:1990 which is withdrawn.The UK participation in its preparation was entrusted to Technic
4、al Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on ACE/12 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Complian
5、ce with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsLicensed Copy: Wang Bin, na, Wed Mar 21 06:59:01 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2335December 2005ICS 49.035 S
6、upersedes EN 2335:1988 English VersionAerospace series - Bearings, spherical plain in corrosionresisting steel without assembly slot - Dimensions and loadsSrie arospatiale - Rotules lisses en acier rsistant lacorrosion sans encoche dassemblage - Dimensions etchargesLuft- und Raumfahrt - Gelenklager
7、auskorrosionsbestndigem Stahl ohne Einfhrnut - Mae undBelastungenThis European Standard was approved by CEN on 26 October 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard w
8、ithout any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language
9、made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany,
10、Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre:
11、 rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2335:2005: ELicensed Copy: Wang Bin, na, Wed Mar 21 06:59:01 GMT+00:00 2007, Uncontrolled Copy, (c) BSI2 Contents Page Foreword 3 1 Scope .4 2
12、Normative references .4 3 Terms and definitions.4 4 Symbols and abbreviations5 5 Required characteristics 5 6 Designation .9 7 Marking 9 8 Technical specification.9 EN 2335:2005Licensed Copy: Wang Bin, na, Wed Mar 21 06:59:01 GMT+00:00 2007, Uncontrolled Copy, (c) BSI3 Foreword This European Standar
13、d (EN 2335:2005) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Serv
14、ices of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2006, and conflicting national standards shall be withdrawn at the lat
15、est by June 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This European Standard supersedes EN 2335:1988. According to the CEN
16、/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,
17、 Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 2335:2005Licensed Copy: Wang Bin, na, Wed Mar 21 06:59:01 GMT+00:00 2007, Uncontrolled Copy, (c) BSI4 1 Scope This standard specifies the characteristics of spherical plain bearin
18、gs in corrosion resisting steel, without assembly slot, with or without swaging groove, with or without lubrication holes and grooves, intended for use in fixed or moving parts of aircraft structure and control mechanisms. They may be used in the temperature range from 54 C to 150 C. However, as the
19、y are lubricated with the following greases (see EN 2337): ester type very high pressure grease (code letter A), operating range from 73 C to 121 C or, synthetic hydrocarbon type very high pressure grease general purpose (code letter B), operating range from 54 C to 177 C. Their field of application
20、 when lubricated with grease code letter A is limited to 121 C. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced documen
21、t (including any amendments) applies. ISO 1132-1, Rolling bearings Tolerances Part 1: Terms and definitions. ISO 8075, Aerospace Surface treatment of hardenable stainless steel parts. EN 2030, Steel FE-PM43 Hardened and tempered Bars D 150 mm Aerospace series. 1)EN 2337, Aerospace series Spherical p
22、lain bearings Technical specification. EN 2424, Aerospace series Marking of aerospace products. EN 2491, Aerospace series Molybdenum disulphide dry lubricants Coating methods. EN 3161, Aerospace series Steel FE-PM3801 (X5CrNiCu17-4) Air melted Solution treated and precipitation treated Bar a or D 20
23、0 mm Rm 930 MPa.2)EN 3490, Aerospace series Steel FE-PM3901 (X15CrNi17-3) Air melted Hardened and tempered Bar for machining De 200 mm 900 MPa Rm 1 100 MPa. 2)3 Terms and definitions For the purposes of this standard, the terms and definitions given in ISO 1132-1 apply. 1) Published as AECMA Standar
24、d at the date of publication of this standard 2) Published as AECMA Prestandard at the date of publication of this standard EN 2335:2005Licensed Copy: Wang Bin, na, Wed Mar 21 06:59:01 GMT+00:00 2007, Uncontrolled Copy, (c) BSI5 4 Symbols and abbreviations The following symbols for tolerances are us
25、ed: dmp: single plane mean bore diameter deviation ds: deviation of a single bore diameter Dmp: single plane mean outside diameter deviation Ds: deviation of a single outside diameter : angle of tilt of the outer ring with respect to the inner ring, the spherical surface of the outer ring being comp
26、letely in contact with the inner ring 5 Required characteristics 5.1 Configuration, dimensions and masses According to Figures 1, 2 and 3 and Table 1. The dimensions are expressed in millimetres and apply after surface treatment. 5.2 Surface roughness According to Figures 1 and 2. The values are exp
27、ressed in micrometres and apply before surface treatment. aFor the inner ring bFor the outer ring Figure 1 Bearing without swaging grooves, code letter S EN 2335:2005Licensed Copy: Wang Bin, na, Wed Mar 21 06:59:01 GMT+00:00 2007, Uncontrolled Copy, (c) BSI6 aFor the inner ring bFor the outer ring F
28、igure 2 Bearing with swaging grooves, code letter R Code letter E: Bearing without lubrication holesand groove Code letter F: Bearing with lubrication holes oninner ring and: a lubrication groove on the boreof the inner ring a distribution groove on sphericalsurface of the inner or outer ringCode le
29、tter G: Bearing with lubrication holes on the outer ring and: a lubrication groove on the outer surface of outer ring a distribution groove on spherical surface of the inner or outer ringKey 1 Three holes d3at 120 NOTE The configuration with or without lubrication hole and lubrication groove applies
30、 to bearings either code letter R or code letter S. Figure 3 1EN 2335:2005Licensed Copy: Wang Bin, na, Wed Mar 21 06:59:01 GMT+00:00 2007, Uncontrolled Copy, (c) BSI7 Table 1 d B C D Tolerances m d1d2d3d4k l1l2r1r2r3 Massg Code Nom. 0 0,06 0,1 dmpdsDmpDsmin.+ 0,10 0,2 0,2 0 0,2max. + 0,10 min.d 04 4
31、 5 3 12 6 8 16 3 05 5 06 6 6 4 14 8 10 0,4 to 0,7 13 5 08 8 8 5 16 80 135+10 130,3 to 0,6 15 8 10 10 9 6 19 102+13 c 16 c 0,5 to 0,8 c 12 12 12 12 10 7 22 15 20,2b 18 0,5 11 17 15 24,20,715 a15 12 9 26 90 156+18 24 1,5 22 0,90,6 to 1 8 32 17 28,2 0,717 a17 14 10 30 80113+20 28 2,825 0,910 49 20 33,2
32、 0,720 a20 16 12 35 24 33 2 2,9 29 0,29 65 25 39,40,925 a25 20 16 42 29 38,836 1,47 115 30 44,4 0,930 a30 22 18 47 100133+110 198+34 43,841 0,8 0,5 to 0,8 160 35 35 25 20 55 39 51,8 47 0,9 to 1,3 6 230 40 40 28 22 62 45 58,8 53 315 45 45 32 25 68 50 64,8 60 0,6 to 1 7 460 50 50 35 28 75 120153+130 2
33、310+55 71,82,5 4 66 560 60 60 44 36 90 150194+150 2813+66 86,8 3 4,5 80 1,41 1,2 to 1,7 1,4 to 1,8 0,36 1 100aCode number 1 to be added to the end of identity block. bWithout lubrication holes and groove. cWithout swaging groove. dMaximum values for the user. 5.3 Clearances and loads See Table 2. EN
34、 2335:2005Licensed Copy: Wang Bin, na, Wed Mar 21 06:59:01 GMT+00:00 2007, Uncontrolled Copy, (c) BSI8 Table 2 Internal clearances m Permissible static loads kN axial radial max. d Code number normal code letter N reduced code letter P normal code letter N normal code letter P radial Csaxial aCa04 7
35、,2 0,45 05 12,6 0,8 06 16 1 08 21 1,8 10 31 2,512 40,5 3,5 15 35 to 75 5 to 35 20 10 70 5,317 91,4 6,7 20 40 to 80 5 to 40 25 12 130 9,8 25 216,7 18 30 277,5 25 35 359,9 31 40 50 to 100 5 to 50 30 15 428,8 38 45 558,4 50 50 760,1 64 60 60 to 120 5 to 60 35 20 1056 104,00 aThese values apply to beari
36、ngs without swaging groove. For bearings with swaging grooves, the push-out loads may be smaller than these values. 5.4 Materials Inner ring: according to EN 2030, 55 HRC to 62 HRC Outer ring: according to EN 3490 or EN 3161, 28 HRC to 37 HRC before swaging 5.5 Surface treatment 5.5.1 Outer ring Dry
37、-film lubricant on the spherical surface (antiscoring treatment) applied according to EN 2491. 5.5.2 Inner ring Passivation according to ISO 8075: code letter T Without surface treatment (passivation): without code letter EN 2335:2005Licensed Copy: Wang Bin, na, Wed Mar 21 06:59:01 GMT+00:00 2007, U
38、ncontrolled Copy, (c) BSI9 6 Designation EXAMPLE Description block PLAIN BEARING Identity block EN2335AP15ERT1 Number of this standard Grease code letter (see Clause 1) Internal clearances (see Table 2) Diameter code number d (see Table 1) Lubrication holes and grooves code letter (see Figure 3) Swa
39、ging grooves code letter (see Figures 1 and 2) Surface treatment code letter (see 5.5) Dimensional varieties code number for swaging grooves (see Table 1) NOTE If necessary, the code 9005 shall be placed between the description block and the identity block. 7 Marking EN 2424, style A The marking pos
40、ition is at the manufacturers option. 8 Technical specification See EN 2337 EN 2335:2005Licensed Copy: Wang Bin, na, Wed Mar 21 06:59:01 GMT+00:00 2007, Uncontrolled Copy, (c) BSIBS EN 2335:2005BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body
41、 responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest a
42、mendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be
43、 found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign stand
44、ards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation
45、of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information se
46、rvices are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purch
47、ase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- informatio
48、n about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extrac
49、t may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If the
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1