BS EN 2349-412-2007 Aerospace series — nRequirements and test nprocedures for relays nand contactors — nPart 412 Seal《航空航天系列 继电器和电流接触器用要求和试验程序 密封》.pdf

1、Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/11/2008 02:21, Uncontrolled Copy, (c) BSIg49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58a

2、nd contactors Part 412: SealICS 49.060Aerospace series Requirements and test procedures for relays BRITISH STANDARDBS EN 2349-412:2007BS EN 2349-412:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/11/2008 02:21, Uncontrolled Copy, (c) BSIThis British Standard was published under the au

3、thority of the Standards Policy and Strategy Committee on 29 August 2008 BSI 2008ISBN 978 0 580 56757 5Amendments/corrigenda issued since publicationDate CommentsCompliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standard is the UK implemen

4、tation of EN 2349-412:2007. The UK participation in its preparation was entrusted to Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport

5、to include all the necessary provisions of a contract. Users are responsible for its correct application.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2349-412April 2007ICS 49.060English VersionAerospace series - Requirements and test procedures for relaysand contactors - Part 412: SealSrie aros

6、patiale - Exigences et mthodes dessais desrelais et contacteurs - Partie 412 : tanchitLuft- und Raumfahrt - Anforderungen und Prfverfahren frRelais und Schaltschtze - Teil 412: StirnflchendichtheitThis European Standard was approved by CEN on 19 May 2006.CEN members are bound to comply with the CEN/

7、CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to a

8、ny CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CE

9、N members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Swed

10、en, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref.

11、 No. EN 2349-412:2007: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/11/2008 02:21, Uncontrolled Copy, (c) BSI2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Method 4 4 Requirements.4 BS EN 2349-412:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/11/2008 02:

12、21, Uncontrolled Copy, (c) BSI3 Foreword This document (EN 2349-412:2007) has been prepared by the AeroSpace and Defense Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received t

13、he approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2007, a

14、nd conflicting national standards shall be withdrawn at the latest by October 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, De

15、nmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 2349-412:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CH

16、INA STANDARDS, 12/11/2008 02:21, Uncontrolled Copy, (c) BSI4 1 Scope This standard specifies a method for checking the leakage rate of relays and contactors. It shall be used together with EN 2349-100. 2 Normative references The following referenced documents are indispensable for the application of

17、 this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2349-100, Aerospace series Requirements and test procedures for relays and contactors Part 100: General requirements 1)EN

18、 2349-201, Aerospace series Requirements and test procedures for relays and contactors Part 201: Visual inspection IEC 60068-2-17, Basic environmental testing procedures Part 2: Tests Test Q: Sealing 3 Method 3.1 Mounting For relays or contactors with plug-socket holders, only the switching device s

19、hall be tested. 3.2 Procedure The relay or contactor shall be subjected to a seal test in accordance with IEC 60068-2-17. 4 Requirements 4.1 Gas-tightness Relays or contactors with a sealed volume of more than 30 cm3shall show a leakage rate, at a pressure differential of 100 kPa (1 bar), of at most

20、 1 106cm3/ s per 15 cm3hermetically sealed volume. Relays or contactors with a sealed volume of less than 30 cm3shall show a leakage rate of at most 1 108cm3/ s in accordance with Test Q of IEC 60068-2-17. 4.2 Liquid-tightness 10 s after immersion no visible bubbles shall escape, in accordance with

21、Test Q of IEC 60068-2-17. 4.3 Inspection Test in accordance with EN 2349-201. No signs of leakage or bubbles. 1) In preparation at the date of publication of this standard. BS EN 2349-412:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/11/2008 02:21, Uncontrolled Copy, (c) BSIblankLice

22、nsed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/11/2008 02:21, Uncontrolled Copy, (c) BSIBS EN BSI Group Headquarters389 Chiswick High Road,London W4 4AL, UKLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/11/2008 02:21, Uncontrolled Copy, (c) BSITel +44 (0)20 8996 9001Fax +44 (0)20 8

23、996 Standards Institution (BSI)BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users

24、of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary

25、of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.B

26、uying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ response to orders for in

27、ternational standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its T

28、echnical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standar

29、ds developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Onl

30、ine can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs a

31、nd Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of ne

32、cessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070 Email: