BS EN 2354-1989 Specification for eye-ends threaded control cable in corrosion resisting steel Dimensions and loads《耐蚀钢操纵钢索的带螺纹的孔眼端头规范 尺寸和负荷》.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS EN 2354:1989 Specification for Eye-ends, threaded, control cable in corrosion resisting steel Dimensions and loads This European Standard EN 2354 has the status of a British Standard. UDC 629.7.05:621.854:621.52.053.004.1BSEN 2354:1989 This British Standard, havi

2、ng been prepared under the directionof the Aerospace Standards Policy Committee, waspublished under the authorityof the Board ofBSIandcomes into effect on 31 October 1989 BSI 01-2000 First published October 1989 The following BSI references relate to the work on this standard: Committee reference AC

3、E/14 Draft for comment 88/70402 DC ISBN 0 580 17722 X Cooperating organizations The European Committee for Standardization, under whose supervision this European Standard was prepared, comprises the national standards organizations of the following Western European countries. Austria Oesterreichisch

4、es Normungsinstitut Belgium Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Ireland National Standards

5、 Authority of Ireland Italy Ente Nazionale Italiano di Unificazione Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Instituto Espaol de Normalizacin Sweden Standardiseringskommissionen i Sverige Switzerland Associatio

6、n suisse de normalisation United Kingdom British Standards Institution Amendments issued since publication Amd. No. Date of issue CommentsBSEN 2354:1989 BSI 01-2000 i Contents Page Cooperating organizations Inside front cover National foreword ii Brief history 2 Text of EN 2354 3 National appendix A

7、 Inside back cover National appendix B Inside back coverBSEN 2354:1989 ii BSI 01-2000 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN2354 “Aerospace series. Eye-ends, threaded control

8、cable in corrosion resisting steel. Dimensions and loads”, published by the European Committee for Standardization (CEN). EN2354 was produced as a result of international discussion in which the UK took an active part. A British Standard does not purport to include all the necessary provisions of a

9、contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theENtitle page, pages2 to6,

10、an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2354 September 1988 UDC629.7.05:621.854:62

11、1.52.053.004.1 Key words: Aircraft industry, flight control, flexible cable, cable tensioner, cable-end, dimensions, breaking loads. English version Aerospace series Eye-ends, threaded, control cable in corrosion resisting steel Dimensions and loads Srie arospatiale Embouts il pour tendeurs en acier

12、 rsistant la corrosion Dimensions et charges Luft- und Raumfahrt Spannschrauben mit se aus korrosionsbestndigem Stahl Mae und Belastungen This European Standard was accepted by CEN on1988-03-17. CEN members are bound to comply with the requirements of CEN Internal Regulations which stipulate the con

13、ditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Central Secretariat or to any CEN member. This European Standard exists in

14、three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to CEN Central Secretariat has the same status as the official versions. CEN members are the national standards organizat

15、ions of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stass

16、art 36, B-1050 Brussels CEN 1988 Copyright reserved to all CEN members Ref. No. EN 2354:1988 EEN 2354:1988 BSI 01-2000 2 Brief history This draft European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After enquiries and votes carried out in accordance wi

17、th the rules of this Association, this draft has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. In accordance with the Common CEN/CENELEC Rules, the following countries are bound to impleme

18、nt this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. Contents Page Brief history 2 1 Scope and field of application 3 2 References 3 3 Required characteristics 3 4 Designat

19、ion 6 5 Marking 6 6 Technical specification 6 Figure 4 Table 5EN 2354:1988 BSI 01-2000 3 1 Scope and field of application This standard specifies the characteristics of threaded eye-ends in corrosion resisting steel intended for the turnbuckles of aircraft control cables. 2 References ISO 2020, Aero

20、space Mechanical system parts Preformed flexible steel wire rope for aircraft controls Technical specification. ISO 5855-1, Aerospace construction MJ threads Part 1: Basic profile. ISO 5855-2, Aerospace construction MJ threads Part 2: Dimensions for bolts and nuts. EN 2363, Aerospace series Locking

21、clips for turnbuckles of control cables Dimensions Aerospace series. EN 2462, Steel FE-PA13 Softened Bars D e100mm Aerospace series. EN 2516, Aerospace series Passivation of corrosion resistant steels 1) . EN 2569, Aerospace series Control cable fittings and turnbarrels Technical specification 1) .

22、3 Required characteristics 3.1 Dimensions Tolerances Loads Mass The configuration shall correspond to theFigure and the dimensions shall conform to the values given in theFigure and theTable. 3.2 Surface roughness SeeFigure. 3.3 Material Steel EN 2462. 3.4 Surface treatment Passivation EN 2516. 1) I

23、n preparation.EN 2354:1988 4 BSI 01-2000 Figure EN 2354:1988 BSI 01-2000 5 Table Dimensions in millimeters Thread a A C D E F G H K L M N R t Mass g Minimum breaking load kN b Nominal diameter of cable used Code Designation H11 H8 + 0,60 0,25 + 0,25 0 0,5 0,5 0,5 Code Dimensions 0,5 min. max. 0,5 +1

24、 0 04 MJ 4 0,70 4h6h 2,4 5 10 1 11 15 2,9 8 S 38 3,25 3,36 25,5 3 0,04 4 2,15 1,6 05 MJ 5 0,80 4h6h 2,9 12 15,5 23 3,8 10 S 41,4 4,16 4,33 22 0,05 8 4,45 2,4 L 63,5 44,5 9,3 06 MJ 6 1,00 4h6h 4,9 6 14 4,6 12 S 44,5 5,08 5,27 24,5 5 0,08 14 8,90 3,2 L 66,8 47 17,4 07 MJ 7 1,00 4h6h 5,9 17 17,5 25 5,6

25、 14 S 44,5 6,08 6,27 22 0,10 22 12,45 4 L 66,8 44,5 26,4 08 MJ 8 1,00 4h6h 6,4 8 20 1,5 18,5 28 6,6 16 S 70 7,08 7,27 6 36,6 18,60 4,8 10 MJ10 1,25 4h6h 7,4 23 20 31 7,8 20 S 73 8,98 9,19 45,5 8 55,4 24,90 5,6 12 MJ12 1,25 4h6h 7,9 10 25 23,5 35 9,8 24 S 79,5 10,98 11,19 48,5 80,7 31,20 6,4 a Confor

26、ming to ISO 5855-1 and ISO 5855-2, rolled. b Equal to the one of the cable used according to ISO2020. 0 0,1 0 0,15EN 2354:1988 6 BSI 01-2000 4 Designation Each threaded eye-end shall only be designated as in the following example: Where the following codes are applied for the thread direction: R = r

27、ight-hand thread L = left-hand thread NOTEIf necessary, originator code S9005 may be introduced between the description block and identity block. 5 Marking In addition to the manufacturers own marking, each threaded eye-end shall be marked (seeFigure) using the identity block as defined in clause4 o

28、f this standard. The marking method is to the manufacturers option. 6 Technical specification The threaded eye-ends supplied according to this standard shall conform with the requirements of EN2569.BSEN 2354:1989 BSI 01-2000 National appendix A The United Kingdom participation in the preparation of

29、this European Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/14 upon which the following bodies were represented: British Independent Steel Producers Association Civil Aviation Authority (Airworthiness Division) Federation of Wire Rope Manufactu

30、rers of Great Britain Ministry of Defence Society of British Aerospace Companies Ltd. Stainless Steel Wire Export Group National appendix B The British Standards corresponding to the European and International Standards referred to in the text are identical in number and title to those given in clau

31、se2 with the exception of ISO2020, ISO5855-1 and ISO5855-2 for which the corresponding British Standards are British Standard W13 (related), BS6293-1 (identical) and BS6293-2 (identical) respectively.BS EN 2354:1989 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the i

32、ndependent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that th

33、ey possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the i

34、dentity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and forei

35、gn standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on

36、 standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Infor

37、mation Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:0208996700

38、1. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or trans

39、mitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.