BS EN 2365-1989 Specification for collars aluminium alloy《铝合金轴环规范》.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS EN 2365:1989 Specification for Collars, aluminium alloy This European Standard EN2365 has the status of a British Standard. UDC 621.887.6034.715:629.7BSEN2365:1989 This British Standard, having been prepared under the directionof the Aerospace Standards Policy Co

2、mmittee, waspublished under the authorityof the Board of BSI on 30November1989 BSI 01-2000 The following BSI references relate to the work on this standard: Committee reference ACE/14 Draft for comment 88/72214 DC ISBN 0 580 17927 3 Cooperating organizations The European Committee for Standardizatio

3、n, under whose supervision this European Standard was prepared, comprises the national standards organizations of the following Western European countries. Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standardiso

4、imisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Icelandic Council for Standardization Ireland National Standards Authority of Ireland Italy Ente Nazionale Italiano di Unificazione Luxembu

5、rg Inspection des travails et des mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Instituto Espaol de Normalizacin Sweden Standardiseringskommissionen i Sverige Switzerland Association suisse de normalisation Un

6、ited Kingdom British Standards Institution Amendments issued since publication Amd. No. Date of issue CommentsBSEN2365:1989 BSI 01-2000 i Contents Page Cooperating organizations Inside front cover National foreword ii Brief history 2 Text of EN 2365 3 National appendix A Inside back cover National a

7、ppendix B Inside back coverBSEN2365:1989 ii BSI 01-2000 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN2365 “Aerospace series. Collars, aluminium alloy” published by the European Commi

8、ttee for Standardization (CEN). EN2365 was produced as a result of international discussion in which the UK took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compli

9、ance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2 to4, an inside back cover and a back cover. This standard has been updated (see copyright date

10、) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN2365 March1989 UDC: 621.887.6-034.715:629.7 Key words: Aircraft industry Bushings Aluminium alloys Specifications, designation, dime

11、nsions English version Aerospace series Collars, aluminium alloy Srie arospatiale Bagues en alliage daluminium Luft- und Raumfahrt Ringe aus Aluminiumlegierung This European Standard was accepted by CEN on1988-05-26. CEN members are bound to comply with the requirements of CEN Internal Regulations w

12、hich stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Central Secretariat or to any CEN member. This Europe

13、an Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to CEN Central Secretariat has the same status as the official versions. CEN members are the nation

14、al standards organizations of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxemburg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr

15、 Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels CEN1989 Copyright reserved to CEN members Ref. No. EN2365:1989 EEN2365:1989 2 BSI 01-2000 Brief history This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After enquiries and votes

16、 carried out in accordance with the rules of this Association, this Standard has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. According to the Common CEN/CENELEC Rules, following countrie

17、s are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxemburg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Brief history 2 1 Scope and field of application 3 2 Refer

18、ences 3 3 Required characteristics 3 4 Designation 4 5 Marking 4 Figure Configuration 3 Table Dimensions and masses 4EN2365:1989 BSI 01-2000 3 1 Scope and field of application This standard specifies the characteristics of aluminium alloy collars for use in aerospace applications, in conjunction wit

19、h shear pins EN2364 and split pin EN2367. 2 References EN 2101, Aerospace series Chromic acid anodizing of aluminium and wrought aluminium alloys. EN 2364, Aerospace series Pins, shear, headed, close tolerance. EN 2367, Aerospace series Split pins in steel EN2573. EN 2387, Aluminium alloy 2014A-T6 T

20、ubes for structures0,6mm k a k 12,5mm Aerospace series. EN 2424, Aerospace series Identification marking of standard fasteners. 3 Required characteristics 3.1 Configuration Dimensions Tolerances Configuration shall correspond to theFigure. The dimensions and tolerances shall correspond to theFigure

21、and theTable. These apply after chromic anodizing. 3.2 Surface roughness R a=3,24m, on all surfaces This value applies prior to chromic acid anodizing. 3.3 Material Aluminium alloy EN2387. 3.4 Surface treatment Chromic acid anodizing EN2101, type B. Figure ConfigurationEN2365:1989 4 BSI 01-2000 Tabl

22、e Dimensions and masses 4 Designation Each collar shall only be designated as in the following example: NOTEIf necessary the originator codeS9005 may be introduced between the description block and the identity block. 5 Marking EN2424, style G. Dimensions in millimetres Diameter code D E 0,25 F G H1

23、3 Mass kg/1000 pieces max. min. 030 3,1 3 6 4,5 1,1 0,3 040 4,1 4 7 5 1,5 0,4 050 5,1 5 8 5,5 1,9 0,5 060 6,15 6 9 5,5 1,9 0,6 070 7,15 7 10 6 2,4 0,7 080 8,15 8 11 6 2,4 0,8 100 10,15 10 13 6,5 3 1,1 0 0,25BSEN2365:1989 BSI 01-2000 National appendix A The United Kingdom participation in the prepara

24、tion of this European Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/14 upon which the following bodies were represented: British Independent Steel Producers Association Civil Aviation Authority (Airworthiness Division) Federation of Wire Rope M

25、anufacturers of Great Britain Ministry of Defence Society of British Aerospace Companies Limited Stainless Steel Wire Export Group National appendix B The British Standards corresponding to the European Standards referred to in the text are identical in number and title with those given in clause2.B

26、S EN 2365:1989 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions Britis

27、hStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while

28、using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically rec

29、eive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementatio

30、n of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information

31、 services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For det

32、ails of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyrigh

33、t, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the sta

34、ndard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.