BS EN 2430-1995 Ethylene-propylene rubber (EPM EPDM) - Hardness 70 IRHD《乙丙橡胶(EPM EPDM) 硬度 70 IRHD(国际橡胶硬度标度)》.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS EN 2430:1995 Ethylene-Propylene Rubber (EPM/EPDM) Hardness 70 IRHD The European Standard EN 2430:1995 has the status of a British Standard ICS 49.040.10BSEN2430:1995 This British Standard, having been prepared under the directionof the Engineering SectorBoard (E/

2、-), was publishedunder the authorityofthe Standards Boardand comes into effect on 15 November 1995 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference ACE/25 Draft for comment 90/72816 DC ISBN 0 580 24085 1 Committees responsible for this British Standar

3、d The preparation of this British Standard was entrusted to Technical Committee ACE/25, Rubber and elastomeric materials for aerospace purposes, upon which the following bodies were represented: British Adhesives and Sealants Association British Hydromechanics Research Group British Narrow Fabrics A

4、ssociation British Rubber Manufacturers Association Ltd. Ministry of Defence Society of British Aerospace Companies Limited Amendments issued since publication Amd. No. Date CommentsBSEN2430:1995 BSI 09-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 1

5、Scope 3 2 Normative references 3 3 Application of the material 3 4 Properties 3 5 Designation 3 6 Technical specification 3 Table 1 Test methods 4 Table 2 Tests after exposure to test media 5 List of references Inside back coverBSEN2430:1995 ii BSI 09-1999 National foreword This British Standard has

6、 been prepared by Technical Committee ACE/25 and is the English language version of EN 2430:1994, Aerospace Series Ethylene propylene rubber (EMP/EPDM) Hardness 70 IRHD, published by the European Committee for Standardization (CEN). EN2430 was produced as a result of international discussion in whic

7、h the United Kingdom took an active part. The European Standard EN 3207, referred to in clause2, is in preparation and there is at present no corresponding British Standard. Preliminary copies of prEN 3207 are available from: BNAE, Technopolis 54, 199 rue Jean Jacques Rousseau, 92138 Issy les Moulin

8、eaux Cedex, Paris, France. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-referenc

9、es Publication referred to Corresponding British Standard ISO 1629:1987 BS 3502 Symbols for plastics and rubber materials Part 2:1991 Schedule for symbols for rubbers ISO 1817:1985 BS 903 Physical testing of rubber Part A16:1987 Determination of the effects of liquids Summary of pages This document

10、comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover

11、.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2430 September 1995 ICS 49.040.10 Descriptors: Aircraft industry, rubber, ethylene-propylene rubber, hardness English version Aerospace series Ethylene-propylene rubber (EPM/EPDM) Hardness 70 IRHD Srie arospatiale lastomre thylne-propylne (EPM/EP

12、DM) Duret 70 DIDC Luft- und Raumfahrt Ethylen-Propylen-Elastomer (EPM/EPDM) Hrte 70 IRHD This European Standard was approved by CEN on 1995-03-02. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of

13、a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version

14、 in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece

15、, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1995 Copyright reserv

16、ed to CEN members Ref. No. EN 2430:1995 EEN2430:1995 BSI 09-1999 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has successively

17、received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Mar

18、ch 1996, and conflicting national standards shall be withdrawn at the latest by March 1996. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,

19、Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom.EN2430:1995 BSI 09-1999 3 1 Scope This standard specifies the properties of ethylene-propylene rubber (EPM/EPDM) 1) , hardness 70 IRHD, for aerospace applications. 2 Normative references This European Standard inco

20、rporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this Euro

21、pean Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. ISO 1629, Rubber and latices Nomenclature. ISO 1817, Rubber, vulcanized Determination of the effect of liquids. EN 3207, Aerospace series Rubber comp

22、ounds Technical specification 2) . 3 Application of the material The suitability of the material for a specific application shall be determined by complementary tests carried out on the finished product as the properties specified in this standard are obtained from standard test specimens. 3.1 Typic

23、al use Application requiring a resistance to ozone, weather and phosphate ester based hydraulic fluids. NOTEThis material shall not be used for the manufacture of dynamic seals in flight hydraulic systems. 3.2 Temperature range 4 Properties SeeTable 1 andTable 2. For qualification, all tests shall b

24、e performed. For batch acceptance, the tests identified inTable 1 andTable 2 shall be performed. 5 Designation 6 Technical specification EN 3207 1) Symbol as per ISO 1629 2) In preparation at the date of publication of this standard Continuous service : from 55 C to + 125 C Intermittent service : fr

25、om 55 C to + 160 CEN2430:1995 4 BSI 09-1999 Table 1 Test methods Line Column 1 2 3 Properties Units Requirements 1 Hardness IRHD a 2 3 Density Mg/m 3 ba 4 5 Tensile strength MPa 10 min. a 6 7 Elongation at break % 200 min. a 8 9 Modulus at % strain MPa 10 11 Tear strength N/mm 20 min. 12 13 Resistan

26、ce to low temperatures TR10 C 30 max. 14 Crystallization Point 15 Compression set 15.1 after 70 h to 100 C % 40 max. a 15.2 after h to C 16 Ozone resistance Ozone concentration : (200 20) pphm 17 Elongation of test piece : 20 % Nil cracking Time : 168 h Temperature : 30 C 18 Corrosion and adhesion o

27、n metals in a dry atmosphere 19 Time : h Temperature : C 20 Corrosion and adhesion on metals in a damp atmosphere Time : h 20.1 Temperature : C Humidity : % Time : h 20.2 Temperature : C Humidity : % 21 22 23 24 25 26 27 28 39 30 a Test for batch acceptance b The value determined for each batch shal

28、l not differ from that determined at qualification by more than 0,02 Mg/m 3 . 70 + 5 4EN 2430:1995 BSI 09-1999 5 Table 2 Tests after exposure to test media Line Column 1 2 3 4 5 1 Test media Air Test fluid 103 see ISO 1817 2 Conditions of exposure in test media Units 70 h/125 C 24 h/100 C 3 Permitte

29、d variation of the properties compared to the initial value Volume % a 4 Mass % 5 Tensile strength % 15 max. 30 max. 6 Elongation at break % 20 max. 20 max. 7 Hardness IRHD 8 a Test for batch acceptance +20 0 +10 0 0 156 blankBSEN2430:1995 BSI 09-1999 List of references See national foreword.BS EN 2

30、430:1995 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStand

31、ards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using

32、this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive t

33、he latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of t

34、hose that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information servi

35、ces are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details o

36、f these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Des

37、igns and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard,

38、 of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.