1、BRITISH STANDARD AEROSPACE SERIES BS EN 2552:1993 Rivets, solid,100 normal countersunk head with dome, in aluminium alloy2117, anodized or chromated, inch based series The European StandardEN2552:1992 has the status of a British Standard UDC 629.7:621.884.091.6-034.71BSEN2552:1993 This British Stand
2、ard, having been prepared under the directionof the Aerospace Standards Policy Committee, waspublished under the authorityof the Standards Boardand comes into effect on 15February1993 BSI 11-1999 The following BSI references relate to the work on this standard: Committee reference ACE/12 Draft for c
3、omment 88/71828 DC ISBN 0 580 21979 8 Cooperating organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Oesterreichisches Normungsinstitut Belgium
4、 Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland Ireland Na
5、tional Standards Authority of Ireland Italy Ente Nazionale Italiano di Unificazione Luxembourg Inspection du Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Asociacin Espaola de Normalizacin y Cer
6、tificacin Sweden Standardiseringskommissionen i Sverige Switzerland Association suisse de normalisation UnitedKingdom British Standards Institution Amendments issued since publication Amd. No. Date CommentsBSEN2552:1993 BSI 11-1999 i Contents Page Cooperating organizations Inside front cover Nationa
7、l foreword ii Foreword 2 1 Scope 3 2 Normative references 3 3 Required characteristics 3 4 Designation 6 5 Marking 6 6 Technical specification 6 National annex NA (informative) Committees responsible Inside back cover National annex NB (informative) Cross-references Inside back cover Figure 1 4 Figu
8、re 2 6 Table 1 3 Table 1 4 Table 2 5 Table 3 6BSEN2552:1993 ii BSI 11-1999 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN2552:1992 Aerospace series Rivets, solid, 100 normal countersu
9、nk head with dome, in aluminium alloy 2117, anodized or chromated, inch based series, published by the European Committee for Standardization (CEN). EN 2552:1992 was produced as a result of international discussions in which the UnitedKingdom took an active part. A British Standard does not purport
10、to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover
11、, pages i and ii, theENtitle page, pages2 to6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NOR
12、M EN2552 November1992 UDC629.7:621.884.091.6-034.71 Descriptors: Aircraft industry, full rivet, countersunk head rivet, aluminium alloy, anodized metal, dimension, designation, marking English version Aerospace series Rivets, solid,100 normal countersunkhead with dome, in aluminium alloy2117, anodiz
13、ed or chromated, inch based series Srie arospatiale Rivets ordinaires, ttefraise100 normale avec dme, en alliagedaluminium2117, anodiss ou chromats, srie base inches Luft- und Raumfahrt Vollniete, mit100 normalem Senkkopf mit Dom, aus Aluminiumlegierung2117, anodisiert oder chromatiert, Inch-Reihe T
14、his European Standard was approved by CEN on1992-11-16. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
15、 concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into it
16、s own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switze
17、rland and UnitedKingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1992 Copyright reserved to CEN members Ref. No. EN2552:1992 EEN2552:1992 BSI 11-1999 2 Foreword This European Sta
18、ndard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this standard has successively received the approval of the National Associations and the Official Services of the member co
19、untries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May1993, and conflicting national standards shall be withdrawn at the latest by May1993. Accordi
20、ng to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the UnitedKingdom.EN2552:
21、1992 BSI 11-1999 3 1 Scope This standard specifies the characteristics of solid rivets, with100 normal countersunk head, inch based series, in aluminium alloy, anodized or chromated, for maximum operating temperature120 C. 2 Normative references This European Standard incorporates by dated or undate
22、d reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when in
23、corporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 2000, Aerospace series Quality assurance EN aerospace products Approval of the quality system of manufacturers. EN 2101, Aerospace series Chromic acid anodizing of aluminiu
24、m and wrought aluminium alloys. EN 2284, Aerospace series Sulphuric acid anodizing of aluminium and wrought aluminium alloys. EN 2345, Aluminium and aluminium alloy rivets Technical specification Aerospace series 1) . EN 2424, Aerospace series Identification marking of standard fasteners 1) . EN 243
25、7, Aerospace series Chromatic conversion coatings (yellow) for aluminium and aluminium alloys 2) . FED QQ-A-430, Federal specification Identification alloy rod and wire For rivets and cold heading 3) . 3 Required characteristics 3.1 Configuration Dimensions Masses SeeFigure 1 andTable 2 andTable 3.
26、Dimensions and tolerances are expressed in millimetres. They apply after surface treatment. 3.2 Material Aluminium alloy 2117-H13 according to QQ-A-430 (1,6mm k Dk 10mm). The rivet shall be delivered in T4 condition. 3.3 Surface treatment SeeTable 1. Table 1 1) Published as AECMA standard at the dat
27、e of publication of the present standard 2) In preparation at the date of publication of the present standard 3) This specification is published by Superintendent of Documents, US Government Printing office, Washigton, DC 20402, United States. Surface treatment Code EN 2284B A EN 2437-2A B EN 2101B
28、a Not colored rivets - (hyphen) Violet-colored rivets F a Specified in the AECMA standard (prEN2552). Shall be replaced byEN2284B.EN2552:1992 4 BSI 11-1999 Table 1 1)The length range is limited (seeTable 2). 2)Shape optional (except concave) within limiting dimensions 3)Blended convex form permissib
29、le within limiting dimensions Figure 1 Diameter code D 1 a D 2 b D 3 D 4 D 5 D 6 H 1 H 2 H 3 L 2 L 3 R max. min. min. max. min. max. min. min. max. min. max. min. 0,08 016 1,65 1,55 3 2,65 2,4 1,6 2,46 0,6 0,03 0,33 0,25 2,1 024 2,45 2,35 4,65 4,2 3,6 2,4 3,84 1,9 1,6 0,9 0,05 0,44 0,36 2,4 0,8 0,5
30、0,15 032 3,25 3,15 5,8 5,3 4,8 3,2 4,88 2,6 2,3 1,1 0,06 0,49 0,41 2,6 1 0,7 040 4,05 3,94 7,35 6,8 6 4 6,17 3,2 2,8 1,4 0,08 0,6 0,52 3 1,2 0,8 0,25 a D 1max may increase by 0,03, over length (L 2 H 1 ). b Maximum conditionEN2552:1992 BSI 11-1999 5 Table 2 Diameter code 016 024 032 040 Length a Mas
31、s b a Mass b a Mass b a Mass b Code N R kg/1000 pieces N R kg/1000 pieces N R kg/1000 pieces N R kg/1000 pieces 003 3 0,026 004 4 0,032 0,080 0,147 005 5 0,038 0,093 0,170 006 6 0,044 0,106 0,193 0,323 007 7 0,050 0,119 0,216 0,358 008 8 0,056 0,132 0,239 0,394 009 9 0,062 0,145 0,261 0,430 010 10 0
32、,067 0,158 0,284 0,465 011 11 0,073 0,171 0,307 0,500 012 12 0,079 0,184 0,330 0,536 014 14 0,091 0,210 0,376 0,607 016 16 0,103 0,236 0,422 0,678 018 18 0,262 0,467 0,750 020 20 0,288 0,513 0,820 022 22 0,314 0,559 0,891 024 24 0,340 0,605 0,962 026 26 0,366 0,651 1,033 028 28 0,392 0,696 1,105 030
33、 30 0,418 0,742 1,176 032 32 0,444 0,788 1,247 035 35 0,483 0,856 1,353 040 40 0,971 1,531 045 45 1,085 1,709 050 50 1,886 a Tail end code (seeFigure 1) b Approximate values, calculated on the basis, of2,76kg/dm 3 , given for information purpose only L 1 0,5 0 +EN2552:1992 6 BSI 11-1999 4 Designatio
34、n Example: NOTEIf necessary, the originator code19005 shall be placed between the description block and the identity block. 5 Marking 5.1 Rivet identification EN 2424, style G 5.2 Material identification SeeFigure 2 andTable 3. Symbol at manufacturers option Table 3 6 Technical specification EN2345
35、except for approval of manufacturers, seeEN2000. Figure 2 Diameter code 016 024 032 040 T 0,05 0,13 0,15 D 7max. 0,8BSEN2552:1993 BSI 11-1999 National annex NA (informative) Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the Aero
36、space Standards Policy Committee (ACE/-) to Technical Committee ACE/12, upon which the following bodies were represented: Association of Electronics, Telecommunications and Business Equipment Industries British Industrial Fasteners Federation Ministry of Defence Society of British Aerospace Companie
37、s Ltd. National annex NB (informative) Cross-references The British Standards corresponding to the European Standards referred to in the text are identical in number and title with those given in clause2, with the exception of EN2345, EN2424 and EN2437 for which no corresponding British Standards ex
38、ist.BS EN 2552:1993 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions B
39、ritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity w
40、hile using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automaticall
41、y receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implemen
42、tation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic inform
43、ation services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. Fo
44、r details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Cop
45、yright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing th
46、e standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1