BS EN 2591-223-2007 Aerospace series - nElements of electrical nand optical nconnection - nTest methods - nPart 223 Measurement of characteristic impedance of a coaxial connector o.pdf

1、Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/05/2008 08:43, Uncontrolled Copy, (c) BSIg49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58c

2、onnection Test methods Part 223: Measurement of characteristic impedance of a coaxial connector or contactICS 49.060Aerospace series Elements of electrical and optical BRITISH STANDARDBS EN 2591-223:2007BS EN 2591-223:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/05/2008 08:43, Uncon

3、trolled Copy, (c) BSIThis British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2008 BSI 2008ISBN 978 0 580 56477 2Amendments/corrigenda issued since publicationDate Commentscontract. Users are responsible for its correct application.Complia

4、nce with a British Standard cannot confer immunity from legal obligations. National forewordThis British Standard is the UK implementation of EN 2591-223:2007.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology,

5、to Panel ACE/6/-/3, Aerospace Connectors.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2591-223December 2007ICS 49.060E

6、nglish VersionAerospace series - Elements of electrical and optical connection- Test methods - Part 223: Measurement of characteristicimpedance of a coaxial connector or contactSrie arospatiale - Organes de connexion lectrique etoptique - Mthodes dessais - Partie 223: Mesure delimpdance caractristiq

7、ue dun connecteur ou duncontact coaxialLuft- und Raumfahrt - Elektrische und optischeVerbindungselemente - Prfverfahren - Teil 223: Messungder Impedanz eines Koaxial-Steckverbinders oder -KontaktesThis European Standard was approved by CEN on 27 April 2006.CEN members are bound to comply with the CE

8、N/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to

9、 any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.

10、CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sw

11、eden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Re

12、f. No. EN 2591-223:2007: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/05/2008 08:43, Uncontrolled Copy, (c) BSI2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Preparation of specimens.4 4 Apparatus .5 5 Requirement.5 6 Detail to be specified.5 EN 2591-223:2007Licensed Co

13、py: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/05/2008 08:43, Uncontrolled Copy, (c) BSI3 Foreword This document (EN 2591-223:2007) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with t

14、he rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identica

15、l text or by endorsement, at the latest by June 2008, and conflicting national standards shall be withdrawn at the latest by June 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsib

16、le for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, G

17、ermany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 2591-223:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/05/2008 08:43, Unco

18、ntrolled Copy, (c) BSI4 1 Scope This standard specifies a test method of measuring the characteristic impedance of a couple of connectors, a couple of coaxial contacts. It shall be use together with EN 2591-100. 2 Normative references The following referenced documents are indispensable for the appl

19、ication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100, Aerospace series Elements of electrical and optical connection Test methods Part 100: General. EN 315

20、5-002, Aerospace series Electrical contacts used in elements of connection Part 002: List and utilization of contacts. EN 4604-002, Aerospace series Cable, electrical, for signal transmission Part 002: General. 3 Preparation of specimens 3.1 Connectors Each contact shall be wired with the shortest p

21、ossible length of coaxial cable according to EN 4604-002, with the closest impedance to the product standard. The free end of one coaxial cable shall be connected to a load resistor with same value than the cable impedance. 3.2 Contacts Each contact shall be wired with the shortest possible length o

22、f coaxial cable according to EN 4604-002, with the closest impedance to the product standard. Then the contact shall be fitted in a dedicated connector as per EN 3155-002. The free end of one coaxial cable shall be connected to a load resistor with same value than the cable impedance. See Figure 1.

23、EN 2591-223:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/05/2008 08:43, Uncontrolled Copy, (c) BSI5 Key 1 Impedance meter reflectometer 2 Coaxial cable 3 Coaxial male connector (or contact) 4 Coaxial female connector (or contact) 5 Load resistor Figure 1 4 Apparatus The measurement

24、shall require the use of an impedance meter reflection meter. The test signal shall be sinusoidal, frequency range in accordance with product standard needs. 5 Requirement The recorded impedance value of the device under test shall comply with specified value in the product standard. 6 Detail to be

25、specified Coaxial cable type. Impedance meter manufacturer, type and serial number. Frequency of measurement. EN 2591-223:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/05/2008 08:43, Uncontrolled Copy, (c) BSIBS EN BSILicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 08/05/2008

26、08:43, Uncontrolled Copy, (c) BSI389 Chiswick High RoadLondonW4 4AL2591-223:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Roya

27、l Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inac

28、curacy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS whic

29、h ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also a

30、vailable from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on

31、national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20

32、 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.

33、Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the

34、 UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without p

35、rior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.