1、BRITISH STANDARD AEROSPACE SERIESBS EN2608:2005Installation and removal requirements for 8 30 adaptors, threaded, with lockringThe European Standard EN 2608:2005 has the status of a British StandardICS 49.030.99g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44
2、g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Fri Jul 14 07:18:34 BST 2006, Uncontrolled Copy, (c) BSIBS EN 2608:2005This British Standard was published under the authority of the Standards Policy and Strat
3、egy Committee on 28 April 2006 BSI 2006ISBN 0 580 47949 8National forewordThis British Standard is the official English language version of EN 2608:2005. The UK participation in its preparation was entrusted to Technical Committee ACE/69, Aerospace hydraulic systems, fluids and components, which has
4、 the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section enti
5、tled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance
6、 with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related internat
7、ional and European developments and promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 22, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last
8、 issued.Amendments issued since publicationAmd. No. Date CommentsLicensed Copy: Wang Bin, na, Fri Jul 14 07:18:34 BST 2006, Uncontrolled Copy, (c) BSIEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2608 December 2005 ICS 49.030.99 English Version Aerospace series - Installation and removal requ
9、irements for 8 30 adaptors, threaded, with lockring Srie arospatiale - Spcification de montage et de dmontage des raccords implanter 8 30 bague de scurit Luft- und Raumfahrt - Ein- und Ausbaubedingungen fr gerade Einschraubverschraubungen 8 30 mit Sicherungsring This European Standard was approved b
10、y CEN on 28 October 2005. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stan
11、dards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to
12、 the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, N
13、orway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and
14、by any means reserved worldwide for CEN national Members. Ref. No. EN 2608:2005: ELicensed Copy: Wang Bin, na, Fri Jul 14 07:18:34 BST 2006, Uncontrolled Copy, (c) BSI2 Contents Page Foreword 3 1 Scope .4 2 Normative references .4 3 Installation instructions5 3.1 Engineering information.5 3.2 Port p
15、reparation 6 3.3 Adaptor installation 12 4 Replacement instructions 17 4.1 Lockring removal 17 4.2 Adaptor removal19 4.3 Adaptor reuse19 5 Designation .20 Annex A (informative) Comparison of numbers for Rosan and AECMA parts 21 EN 2608:2005Licensed Copy: Wang Bin, na, Fri Jul 14 07:18:34 BST 2006, U
16、ncontrolled Copy, (c) BSI3 Foreword This European Standard (EN 2608:2005) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has re-ceived the a
17、pproval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2006, and co
18、nflicting national standards shall be withdrawn at the latest by June 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According
19、to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Den-mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
20、Luxem-bourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 2608:2005Licensed Copy: Wang Bin, na, Fri Jul 14 07:18:34 BST 2006, Uncontrolled Copy, (c) BSI4 1 Scope This standard specifies the installation and removal requiremen
21、ts for adaptors, threaded, with lockring for pipe couplings 830 according to EN 2603. This standard establishes an accurate procedure of adaptor installation, removal and reinstallation to ensure the repeatability of the installation operation and to ensure the effective compliance to sealing and lo
22、cking re-quirements. The adaptor shown on all figures of this standard is given as an example for the 830 interface according to EN 2604. This procedure is used for adaptors 830, for nominal pressure up to 28 000 kPa to install the adapters according to EN 3248, EN 3270 and EN 3566. 2 Normative refe
23、rences The following referenced documents are indispensable for the application of this document. For dated refer-ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 5855-1, Aerospace MJ threads Part 1:
24、General requirements ISO 5855-3, Aerospace MJ threads Part 3: Limit dimensions for fluid systems EN 2435-01, Aerospace series Paints and varnishes Corrosion resistant chromated two component cold curing primer Part 01: Minimum requirements EN 2602, Aerospace series Ports for adaptors, threaded, with
25、 lockring Geometric configuration EN 2603, Aerospace series Port ends for adaptors, threaded, with lockring Geometric configuration EN 2604, Aerospace series 830 interface for adaptors, threaded, with lockring Geometric configuration EN 2645, Aerospace series Lockrings for adaptors, threaded, with l
26、ockring Dimensions EN 3248, Aerospace series Pipe coupling 830 in titanium alloy Adaptors, reduced pipe end, with lock-ring EN 3270, Aerospace series Pipe coupling 830 in titanium alloy Blanking plugs with lockring EN 3566, Aerospace series Pipe coupling 830 in titanium alloy Adaptors with lockring
27、EN 3663, Aerospace series Pipe coupling O-rings in rubber NBR, 75 IRHD Temperature range: 55 C to +135 C MIL-H-5606, Hydraulic fluid, petroleum base; aircraft, missile and ordnance1)MIL-H-83282, Hydraulic fluid, fire resistant, synthetic hydrocarbon base, metric, NATO number H-5371)MIL-H-87257, Hydr
28、aulic fluid, fire resistant, low temperature, synthetic hydrocarbon base, aircraft and missile1)1) Published by: Department of Defence (DOD), the Pentagon, Washington, D.C. 20301. EN 2608:2005Licensed Copy: Wang Bin, na, Fri Jul 14 07:18:34 BST 2006, Uncontrolled Copy, (c) BSI5 3 Installation instru
29、ctions 3.1 Engineering information aThe adaptor according to EN 3566 is used in the 830 coupling system with an interface according to EN 2604. bThe lockring according to EN 2645 prevents the adaptor from rotating in the port and also avoids port damage at tubing installation due to torquing. cSeal
30、is metal to metal and O-ring according to EN 3663. NOTE This seal is only compatible with hydraulic fluids such as MIL-H-5606, MIL-H-83282 and MIL-H-87257. dTapped hole (boss port side) for the 830 adaptor installation according to EN 2602. ePort side interface of the adaptor according to EN 2603. f
31、Thread A gThread B Figure 1 Comparison of numbers for Rosan and AECMA parts see Annex A. EN 2608:2005Licensed Copy: Wang Bin, na, Fri Jul 14 07:18:34 BST 2006, Uncontrolled Copy, (c) BSI6 Table 1 General information Dimensions in millimetres O-ring Thread AbThread BbPart No. x y 830 coupling CodeaAd
32、aptor Part No. EN Port dimension code 4g6g 4h6h EN max. 0,50 05 3566-0605 077 MJ10 1MJ6 1 3663A0045 3,2 10,8006 3566-0806 098 MJ12 1,25 MJ8 1 3663A0060 3,65 12,75 08 3566-1008 125 MJ14 1,5 MJ10 1 3663A0080 4,10 15,00 10 3566-1210 136 MJ16 1,5 MJ12 1,25 3663A0095 4,10 15,00 12 3566-1412 153 MJ18 1,5
33、MJ14 1,5 3663A0112 4,10 15,00 14 3566-1614 170 MJ20 1,5 MJ16 1,5 3663A0132 4,10 15,20 16 3566-1816 192 MJ22 1,5 MJ18 1,5 3663A0150 4,10 15,20 18 3566-2018 214 MJ24 1,5 MJ20 1,5 3663A0170 4,10 15,00 20 3566-2220 231 MJ27 1,5 MJ22 1,5 3663A0190 4,10 15,60 22 3566-2422 253 MJ30 1,5 MJ24 1,5 3663A0212 4
34、,10 15,60 25 3566-2725 295 MJ33 1,5 MJ27 1,5 3663A0236 4,10 16,00 28 3566-3028 320 MJ36 1,5 MJ30 1,5 3663A0265 4,10 16,00 32 3566-3332 350 MJ39 1,5 MJ33 1,5 3663A0300 4,10 16,00 aCorresponds to the pipe nominal outside diameter. bAccording to ISO 5855-3, except MJ6 1. MJ6 1 according to ISO 5855-1.
35、3.2 Port preparation The manufacturing sequence of port preparation is for information only. Qualification of the assembly is required for each manufacturing sequence and type of tool for a given port material installation method and nominal pressure. The hole shall conform to EN 2602, using the app
36、licable tools for tap drilling port machining serration broaching thread cutting NOTE The design office may specify a hole without serration pre-broaching, when low resistance material is used. EN 2608:2005Licensed Copy: Wang Bin, na, Fri Jul 14 07:18:34 BST 2006, Uncontrolled Copy, (c) BSI7 3.2.1 T
37、ap drilling See Figure 2. Drill through or to a depth as required in Table 2. Table 2 Port drilling Dimensions in millimetres d1d2d3l1bl2c830 coupling CodeaPort dimension code 076,00+min. min. 05 077 5,065 17,05 2,5 17,00 19,00 06 098 7,065 19,05 4,4 18,10 20,10 08 125 9,065 21,60 6,1 19,40 21,40 10
38、 136 10,821 24,15 7,7 20,725 23,225 12 153 12,576 26,55 9,0 21,95 24,95 14 170 14,576 27,95 10,7 22,65 25,65 16 192 16,576 29,85 12,5 23,25 26,25 18 214 18,576 33,05 14,2 24,95 27,95 20 231 20,576 36,60 15,9 25,65 28,65 22 253 22,576 38,85 17,6 26,45 29,45 25 295 25,576 42,45 20,2 27,45 30,45 28 320
39、 28,576 46,00 22,8 28,45 31,45 32 350 31,576 48,25 25,4 29,45 32,45 aCorresponds to the pipe nominal outside diameter. bl1= l6+ 2,5 pitch (for hand tap) cl2= l6+ 4,5 pitch (for machining tap) Figure 2 EN 2608:2005Licensed Copy: Wang Bin, na, Fri Jul 14 07:18:34 BST 2006, Uncontrolled Copy, (c) BSI8
40、3.2.2 Port machining The port machining shall be made in accordance with EN 2602. Special porting tools may be used as shown in Figure 3 and Table 3. Table 3 Porting tool Dimensions in millimetres d4cd5d6l3l4c830 coupling CodeaPort dimension code Tool Part No.bEN 0008,0 0,013 0,008 0,15 0,75 05 077
41、2608PT077 9,995 5,103 12,030 16,13 101,6 06 098 2608PT098 9,995 7,103 14,040 16,93 86,8 08 125 2608PT125 9,995 9,103 17,060 17,68 87,5 10 136 2608PT136 14,995 10,860 18,660 18,38 88,212 153 2608PT153 14,995 12,614 20,240 19,03 94,6 14 170 2608PT170 14,995 14,614 21,840 19,68 95,616 192 2608PT192 14,
42、995 16,614 25,420 21,09 97,3 18 214 2608PT214 24,995 18,614 27,070 22,79 105,320 231 2608PT231 24,995 20,614 29,380 23,49 106,0 22 253 2608PT253 24,995 22,614 32,560 25,67 108,225 295 2608PT295 24,995 25,614 36,060 26,72 109,3 28 320 2608PT320 24,995 28,614 39,690 27,72 116,632 350 2608PT350 24,995
43、31,614 42,080 28,72 117,6 aCorresponds to the pipe nominal outside diameter. bPT: Porting Tool. This tool counterbores, countersinks, provides a radius and produces a tap drill diameter in one pass. Contours are ground to ensure concentricity. Cutter geometry and material permit the use of this tool
44、 with most common materials. cFor information only Dimensions in millimetres aFor information only Figure 3 EN 2608:2005Licensed Copy: Wang Bin, na, Fri Jul 14 07:18:34 BST 2006, Uncontrolled Copy, (c) BSI9 3.2.3 Serration broaching Broaching shall be made according to EN 2602. Special broaching too
45、l can be used as shown in Figure 4 and Table 4. In this case the following procedure shall apply: 1) Prior to broaching, the cutter teeth will rest on the surface of the boss and the body of the tool will be free to move up and down. Note that the nut should be backed away from the body of the tool.
46、 2) The tool may be hand-held or used under a press. 3) Locate broaching tool pilot into the port. 4) Slowly apply a force to the mandrel while holding the body to allow the teeth to broach into the parent material counterbore. 5) Broaching is complete when the external shoulder of the mandrel conta
47、cts the internal shoulder in the body. 6) The installation force is then relieved and the tool is ready for removal. 7) To remove the tool from the boss, turn the nut in clockwise direction against the body and the man-drel will move the cutter up, away from the port counterbore. Table 4 Serration t
48、ool Dimensions in millimetres d7cd8l5cs1c,dt1c830 coupling CodeaPort dimension code Tool Part No.bEN 0,4 Ref. Ref. h13 40,00+05 077 2608BT077 21,3 5,04 136,0 22 1,95 06 098 2608BT098 21,3 7,04 137,3 22 2,3508 125 2608BT125 23,3 9,04 140,6 24 2,75 10 136 2608BT136 26,3 10,80 140,9 27 2,75 12 153 2608
49、BT153 29,3 12,55 140,9 30 2,75 14 170 2608BT170 29,3 14,55 141,6 30 2,75 16 192 2608BT192 35,2 16,55 142,1 36 2,75 18 214 2608BT214 35,2 18,55 142,4 36 2,75 20 231 2608BT231 40,2 20,55 143,4 41 2,75 22 253 2608BT253 40,2 22,55 143,4 41 2,75 25 295 2608BT295 45,2 25,55 143,4 46 2,75 28 320 2608BT320 49,2 28,55 143,4 50 2,75 32 350 2608BT350 54,2 31,55 143,4 55 2,75 aCorresponds to
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1