BS EN 2851-1992 Marking of parts and assemblies other than engines - Indications on drawings《发动机之外的零部件和组件的标志 图纸上标示》.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS EN 2851:1992 Marking of parts and assemblies other than engines Indications on drawings The European Standard EN2851:1992 has the status of a BritishStandardBSEN2851:1992 This BritishStandard, having been prepared under the directionof the Aerospace Standards Pol

2、icy Committee, waspublished under the authorityof the Standards Boardand comes into effect on 15June1992 BSI 01-2000 The following BSI references relate to the work on this standard: Committee reference ACE/- Draft for comment90/70820DC ISBN 0 580 20936 9 Cooperating organizations The European Commi

3、ttee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen

4、 Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland Ireland National Standards Authority of Ireland Italy Ente Nazionale Italiano di Unificazion

5、e Luxembourg Inspection du Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Asociacin Espaola de Normalizacin y Certificacin Sweden Standardiseringskommissionen i Sverige Switzerland Association su

6、isse de normalisation UnitedKingdom British Standards Institution Amendments issued since publication Amd. No. Date CommentsBSEN2851:1992 BSI 01-2000 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 Text of EN2851 3 National annex NA (informative) Committe

7、es responsible Inside back coverBSEN2851:1992 ii BSI 01-2000 National foreword This BritishStandard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN2851:1992, Aerospace series Marking of parts and assemblies other than engine

8、s Indications on drawings, published by the European Committee for Standardization (CEN). EN2851 was produced as a result of international discussions in which theUnitedKingdom took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of Br

9、itish Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2 to6, an inside back cover

10、 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2851 March 1992 UDC 629.7-2:62-777:744.4 Descriptors: Aircraft

11、 industry, drawings, machine components, marking, specification English version Aerospace series Marking of parts and assemblies other than engines Indications on drawings Srie arospatiale Marquage des pices et ensembles autres que moteurs Indications sur dessins Luft- und Raumfahrt Kennzeichnung vo

12、n Bauteilen und Baugruppen ausgenommen Triebwerke Angaben in Zeichnungen This European Standard was approved by CEN on1992-03-20. CEN members are bound to comply with of the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national sta

13、ndard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other

14、language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ire

15、land, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland andUnitedKingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels CEN1992 Copyright reserved to CEN mem

16、bers Ref. No. EN2851:1992 EEN2851:1992 BSI 01-2000 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has successively received the a

17、pproval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. According to the Common CEN/CENELEC Rules, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Gr

18、eece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. Contents Page Foreword 2 1 Scope and field of application 3 2 Purpose of marking 3 3 Indications on drawings 3 3.1 General 3 3.2 Marking symbol 3 3.3 Location of marking 3 3.4 Comp

19、osition of the marking 4 3.5 Marking process 5 4 Reference to this standard on drawings 6 Figure 1 3 Figure 2 3 Figure 3 3 Figure 4 4 Figure 5 4 Figure 6 5 Figure 7 5 Figure 8 5 Figure 9 6 Table 1 5 Table 2 6EN2851:1992 BSI 01-2000 3 1 Scope and field of application This standard defines the method

20、of indicating on drawings, with the exception of engine drawings, the instructions for the marking of parts and assemblies for aerospace applications. It is applicable whenever referenced. 2 Purpose of marking The marking shall allow the identification and traceability of parts and assemblies. 3 Ind

21、ications on drawings 3.1 General Drawings shall indicate the location and composition of the marking and the marking process(es). 3.2 Marking symbol A circle divided into4 quadrants as shown in Figure 1. This symbol shall be connected to the location of the marking by a line ending in an arrow or a

22、dot (see3.3.2). The size of the symbol shall be compatible with micro-filming requirements as well as those of computer aided design. 3.3 Location of marking 3.3.1 Choice It shall be such that the marking: does not impair the manufacturing tolerances or the required surface conditions, does not jeop

23、ardize strength, remains visible after installation, if possible. 3.3.2 Identification 3.3.2.1 No precise location within an area on a surface The line shall end in a dot or an arrow depending upon which view is used to indicate the surface (seeFigure 2 and Figure 3). 3.3.2.2 Location defined within

24、 an area on a surface The line shall end in a dot inside the zone defined by a fine chain-dotted line (see Figure 4). This zone may be dimensioned. Figure 1 Figure 2 Figure 3 EN2851:1992 4 BSI 01-2000 3.3.2.3 Optional location The information concerning the composition of the marking (see3.4) and th

25、e marking process(es) (see3.5) shall be combined with reference to this standard (see4). 3.4 Composition of the marking The marking may include any of the elements listed in Table 1. The choice of elements shall be the responsibility of the design office but in accordance with the specific project r

26、ules. The composition shall be established on the drawings by entering codes above the horizontal part of the identification line (see Figure 5). Figure 4 Figure 5 EN2851:1992 BSI 01-2000 5 Table 1 3.5 Marking process The marking processes are set out in Table 2. The choice shall be the responsibili

27、ty of the design office but in accordance with the specific project rules. It shall be indicated on the drawings as follows: 3.5.1 Only one process is permissible The code corresponding to the chosen process (see Figure 6) shall be written in the lower quadrant of the symbol. 3.5.2 Choice of more th

28、an one process is permissible Codes corresponding to the chosen processes shall be written in the quadrants of the symbol (see Figure 7). If necessary, multiple symbols shall be used (see Figure 8). 3.5.3 Process choice is unrestricted The corresponding code shall be placed in the lower quadrant of

29、the symbol (see Figure 9). Code Elements 1 Part number of the part or assembly awith, possibly the modification number or issue status 2 Manufacturers identification (name, logo, code) 3 Serial number 4 Production batch number 5 Material batch number 6 Sub-contractors identification 7 Life code 8 Ma

30、terial type (only for as received parts) 9 Category of the as received part (casting, band and die forging) 10 Identification of melt (of a casting) 11 Purchasers stores code Inspection stamp b Identification of non-conformance c a If the marking includes the part number, it shall be placed at the h

31、ead of the entry. b Being always necessary, this element does not need a code. c This information is not known by the design office at the time the drawings are issued, therefore it is not possible to allocate a code. Figure 6 Figure 7 Figure 8 EN2851:1992 6 BSI 01-2000 Table 2 4 Reference to this s

32、tandard on drawings The following shall be written in the appropriate space, in the drawing title block, or nearby: or, if the location is optional (see3.3.2.3): The composition of the marking (1-2) and the marking process (V) are to be considered as an example. Figure 9 Codes Processes A Adhesive l

33、abel B Tag or marking on packing C Chemical engraving D Transfer (decal) E Electrolytic engraving F Manual punch marking G Tool or machine engraving H Fixed label J Sand blasting K Electric pencil L Control punch marking M Hot pressure P Paint R By casting or forging S Silk screen print T Marking wi

34、th indelible ink (by hand or stamp) V Vibro-engrave X No process specified Y LaserBSEN2851:1992 BSI 01-2000 National annex NA (informative) Committees responsible The UnitedKingdom participation in the preparation of this European Standard was undertaken by the Aerospace Standards Policy Committee (

35、ACE/-) upon which the following bodies were represented: British Airways Civil Aviation Authority (Airworthiness Division) Department of Trade and Industry Institution of Manufacturing Engineers Ministry of Defence Society of British Aerospace Companies Ltd.BS EN 2851:1992 BSI 389 Chiswick High Road

36、 London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or re

37、vision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform t

38、he Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Bu

39、ying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as Br

40、itishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give d

41、etails on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact

42、Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extrac

43、t may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbo

44、ls, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.