BS EN 2865-2009 Aerospace series - Nuts anchor self-locking floating two lugs with counterbore in heat resisting steel MoS2 lubricated - Classification 1100 MPa (at ambient tempera.pdf

1、BS EN 2865:2009ICS 49.030.30NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Nuts, anchor, self-locking, floating, twolugs, with counterbore,in heat resisting steel,MoS2 lubricated Classification: 1 100MPa (at ambienttemperature) / 315 CLicensed

2、Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:36, Uncontrolled Copy, (c) BSIThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 January2010 BSI 2010ISBN 978 0 580 69809 5Amendments/corrigenda issued since publicationDate CommentsBS E

3、N 2865:2009National forewordThis British Standard is the UK implementation of EN 2865:2009.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained onrequest to

4、its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06

5、:36, Uncontrolled Copy, (c) BSIBS EN 2865:2009EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2865 November 2009 ICS 49.030.30 English Version Aerospace series - Nuts, anchor, self-locking, floating, two lugs, with counterbore, in heat resisting steel, MoS2 lubricated - Classification: 1 100 MP

6、a (at ambient temperature) / 315 C Srie arospatiale - crous river, freinage interne, flottants, double patte, avec chambrage, en acier rsistant chaud, lubrifis MoS2 - Classification : 1 100 MPa ( temprature ambiante) / 315 C Luft- und Raumfahrt - Annietmuttern, selbstsichernd, bewegli, beiderseitige

7、r Flansch, mit zylindrischer Aussenkung, aus hochwarmfestem Stahl, MoS2-geschmiert - Klasse : 1 100 MPa (bei Raumtemperatur) / 315 C This European Standard was approved by CEN on 17 October 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions

8、 for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three off

9、icial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austri

10、a, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMIT

11、TEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2865:2009: ELicensed Copy: Wang Bin, IS

12、O/EXCHANGE CHINA STANDARDS, 25/03/2010 06:36, Uncontrolled Copy, (c) BSIBS EN 2865:2009EN 2865:2009 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Required characteristics .54 Designation 75 Marking .76 Technical specification .7Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS

13、, 25/03/2010 06:36, Uncontrolled Copy, (c) BSIBS EN 2865:2009EN 2865:2009 (E) 3 Foreword This document (EN 2865:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of th

14、is Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by e

15、ndorsement, at the latest by May 2010, and conflicting national standards shall be withdrawn at the latest by May 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifyi

16、ng any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,

17、Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:36, Uncontrolled Copy, (c) BSIBS EN 2865

18、:2009EN 2865:2009 (E) 4 1 Scope This European Standard specifies the characteristics of two lugs, counterbored floating anchor nuts, with a self-locking feature achieved by forming the upper portion out-of-round, in heat resisting steel, MoS2lubricated. Classification: 1 100 MPa 1) / 315 C 2). 2 Nor

19、mative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2398, Aerospace series Heat

20、resisting steel FE-PA2601 (X6NiCrTiMoV26-15) Rm 900 MPa Bars for machined bolts D 25 mm EN 2399, Aerospace series Heat resisting steel FE-PA2601 (X4NiCrTiMoV26-15) Rm 900 MPa Bars for forged bolts D 25 mm EN 2424:2008, Aerospace series Marking of aerospace products EN 2491, Aerospace series Molybden

21、um disulphide dry lubricants Coating methods EN 3638, Aerospace series Heat resisting alloy FE-PA2601 (X6NiCrTiMoV26-15) Consumable electrode remelted Solution and precipitation treated Sheet, strip and plate 0,5 mm a 10 mm EN 3639, Aerospace series Heat resisting alloy FE-PA2601 Softened and cold w

22、orked Wire for forged fasteners D 15 mm 900 MPa Rm 1 100 MPa 3)EN 3816, Aerospace series Steel FE-PA3601 (X6CrNiTi18-10) Air melted Softened and cold rolled Sheet and strip a 3 mm Rm 800 MPa EN 9100, Quality Management Systems Requirements for Aviation, Space and Defense Organizations EN 9133, Aeros

23、pace series Quality management systems Qualification procedure for aerospace standard parts ISO 3209, Aerospace Nuts, anchor, self-locking, floating, two lug, with counterbore, with MJ threads, classifications: 1 100 MPa (at ambient temperature)/ 235 C, 1 100 MPa (at ambient temperature)/ 315 C and

24、1 100 MPa (at ambient temperature)/ 425 C Dimensions ISO 5855-2, Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts ISO 5858, Aerospace Nuts, self-locking, with maximum operating temperature less than or equal to 425 C Procurement specification ISO 8788, Aerospace Nuts, metric Toleranc

25、es of form and position 1) Corresponds to strength class of the associated bolt, the 100 % load of which it is able to withstand, when tested at ambient temperature, without breaking or cracking. 2) Maximum temperature that the nut is able to withstand, without permanent alteration to its original c

26、haracteristics, after ambient temperature has been restored. The maximum temperature is conditioned by the surface treatment. 3) Published as ASD-STAN Prestandard at the date of publication of this standard. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:36, Uncontrolled Copy,

27、(c) BSIBS EN 2865:2009EN 2865:2009 (E) 5 TR 3791, Aerospace series Materials for self-locking nuts, threaded inserts and screw thread inserts of temperature classes 425 C 4)3 Required characteristics 3.1 Configuration Dimensions Masses See Figure 1 and Table 1. Dimensions and tolerances are in confo

28、rmity with ISO 3209, expressed in millimetres and apply before MoS2lubrication. Form and position tolerances shall be in conformity with ISO 8788. 3.2 Materials Threaded element: EN 2398, EN 2399, EN 3638, EN 3639 or TR 3791. Cage: EN 3638 or EN 3816. 3.3 Surface treatment EN 2491, thickness not spe

29、cified. These values in micrometres apply before surface treatment. The values do not apply to threads and sheared edges the surface texture of which will be achievedby usual manufacturing methods. Remove sharp edges 0,1 to 0,4. Details of form, not stated, are at the manufacturers option. 4) Publis

30、hed as ASD-STAN Technical Report at the date of publication of this standard. 6,3 3,2 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:36, Uncontrolled Copy, (c) BSIBS EN 2865:2009EN 2865:2009 (E) 6 Key 1 Marking 2 Float inclusive 3 Cage 4 Nut element 5 Form out-of-round in this

31、area to achieve the self-locking. Tooling marks are permitted in this area. 6 Thread 7 Bearing face of the nut 8 Radius or chamfer Figure 1 Alternatives: countersunk rivet holes (when specified by purchaser) may be dimpled or cut countersunk (at manufacturers option). Licensed Copy: Wang Bin, ISO/EX

32、CHANGE CHINA STANDARDS, 25/03/2010 06:36, Uncontrolled Copy, (c) BSIBS EN 2865:2009EN 2865:2009 (E) 7 Table 1 Diameter code Thread aE F GHJbK L M NcP R S T VZ Masskg/1 000piecesapprox.Radial float min.min.max. max. max. max. max. min. max. 0,25 min. 030 MJ30,5-4H6H 8,5 17 dd4,6 11 23,24 0,9 4,53 2,5

33、 4,5 4,8 0,5 1,8 040 MJ40,7-4H6H 4,4 2,2 6,2 5,8 5,5 2 050 MJ50,8-4H6H 9,5 19 5,5 2,4 7,3 12 25,2 6,9 6,50,7 2,3 060 MJ61-4H5H 11 22 6,5 2,7 8,7 13,5 29,2 8,1 7,53,5 4,6 3,8 080 MJ81-4H5H 8,5 10,9 16 9,9 1,1 9,5 3 5,5 5,7 0,75 7,3 100 MJ101,25-4H5H 13 26 10,5 3 12,9 18 35,2 12 11,5 4,5 3,5 6,6 6,6 1

34、0 aIn accordance with ISO 5855-2. In the self-locking zone, the tolerances apply before forming out-of-round. bIs to sharp corners (chamfered) or point of tangency (radiused). cIs applicable at the rivet hole location. dDiameter code 030 does not have a counterbore. 4 Designation EXAMPLE Description

35、 block NUT Identity block EN2865060 Number of this standard Hole code (see Table 2) Diameter code (see Table 1) NOTE If necessary the originator code I9005 shall be placed between the description block and the identity block. Table 2 Option Code Plain rivet holes (hyphen) Countersunk or dimpled rive

36、t holes K 5 Marking EN 2424:2008, style N. See Figure 1. 6 Technical specification ISO 5858, except for: Approval of manufacturers: see EN 9100; Qualification of products: see EN 9133. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:36, Uncontrolled Copy, (c) BSIBS EN2865:2009BS

37、I GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is i

38、ncorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone

39、 finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service cal

40、led PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy direc

41、tly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of

42、 information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +4

43、4 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: I

44、nformation regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the internati

45、onal standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does no

46、t preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 25/03/2010 06:36, Uncontrolled Copy, (c) BSI