BS EN 3011-1998 Bolts hexagon head relieved shank long thread in heat resisting nickel base alloy NI-P101HT (Waspaloy) silver plated - Classification 1210 MPa (at ambient temperatu.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS EN 3011:1998 Bolts, hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy), silver plated Classification: 1210MPa (at ambient temperature)/730C The European Standard EN 3011:1998 has the status of a British Standard IC

2、S 49.030.20BSEN3011:1998 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 July 1998 BSI 04-1999 ISBN 0 580 30161 3 National foreword This British Standard is the Engli

3、sh language version of EN 3011:1998. The UK participation in its preparation was entrusted by Technical Committee ACE/12, Aerospace fasteners and fastening systems, to Subcommittee ACE/12/1, Aerospace fasteners and fastening systems (International), which has the responsibility to: aid enquirers to

4、understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UKinterests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented

5、 on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence

6、 Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itse

7、lf confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages2 to 7 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicat

8、ed in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN3011:1998 BSI 04-1999 i Contents Page National foreword Inside front cover Foreword 2 Text of EN 3011 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3011 May 1998 ICS 49.

9、030.20 Descriptors: Aircraft industry, screw, hexagonal head screw, nickel alloy, heat resistant material, characteristic, surface treatment, screw thread, code, dimension, designation, marking English version Aerospace series Bolts, hexagon head, relieved shank, long thread, in heat resisting nicke

10、l base alloy NI-P101HT (Waspaloy), silver plated Classification: 1210MPa (at ambient temperature)/730C Srie arospatiale Vis tte hexagonale, ft dgag, filetage long, en alliage rsistant chaud base de nickel NI-P101HT (Waspaloy), argentes Classification: 1210 MPa ( temprature ambiante)/730C Luft- und R

11、aumfahrt Sechskantschrauben, Dnnschaft, langes Gewinde, aus hochwarmfester Nickelbasislegierung NI-P101HT (Waspaloy), versilbert Klasse: 1210MPa (bei Raumtemperatur)/730C This European Standard was approved by CEN on 23 February 1998. CEN members are bound to comply with the CEN/CENELEC Internal Reg

12、ulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This

13、European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the

14、national standards bodies of Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europi

15、sches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3011:1998 EEN3011:1998 BSI 04-1999 2 Foreword This European Standard has been prepared by the Eu

16、ropean Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to

17、 CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November1998, and conflicting national standards shall be withdrawn at the latest by November1998. According to the CEN/CENELEC Internal Regul

18、ations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the Un

19、itedKingdom. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Required characteristics 3 4 Designation 7 5 Marking 7 6 Technical specification 7 Figure 1 4 Table 1 4 Table 2 5EN3011:1998 BSI 04-1999 3 1 Scope This standard specifies the characteristics of hexagon headed bolts with relie

20、ved shank and long thread, in NI-P101HT, silver plated, for aerospace applications. Classification: 1210MPa 1) /730 C 2) 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriat

21、e places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication

22、 referred to applies. ISO 3353, Aerospace Rolled threads for bolts Lead and runout requirements. ISO 5855-2, Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts. EN 2424, Aerospace series Marking of aerospace products. EN 2582, Aerospace series Bolts in heat resisting nickel base alloy

23、NI-P101HT (Waspaloy) Classification: 1210 MPa/730 C Technical specification 3) . EN 2786, Aerospace series Electrolytic silver plating of fasteners 3) . EN 2959, Aerospace series Heat resisting nickel base alloy (NI-P101HT) Solution treated and cold worked Bar for hot upset forging for fasteners 3 D

24、 30mm 3) . EN 3220, Aerospace series Heat resisting nickel base alloy (NI-P101HT) Cold worked and softened Bar and wire for continuous forging or extrusion for fasteners 3 D 30mm 3) . 3 Required characteristics 3.1 Configuration Dimensions Tolerances Masses SeeFigure 1 andTable 1 andTable 2. Dimensi

25、ons and tolerances are in millimetres. They apply after silver plating. 3.2 Materials EN2959 or EN3220 3.3 Surface treatment EN2786 Thickness: thread: 34m to 64m shall be measured at the pitch diameter; other areas may show complete coverage, without thickness requirement. 1) Minimum tensile strengt

26、h of the material at ambient temperature 2) Maximum test temperature of the parts 3) Published as AECMA Prestandard at the date of publication of this standardEN3011:1998 4 BSI 04-1999 Table 1 1) When the length of the shank is less than one times the nominal value of the shank diameter D, the runou

27、t is measured at a distance equal to half the actual shank length. 2) For bolts having a shank length less than one times the nominal value of the shank diameter D, and for those threaded to head, the pitch diameter axis shall be used as the datum. Figure 1 Thread a D E F G H K Q R S T U V Code Desi

28、gnation 0,13 min. min. min. 0,5 max. min. h13 050 MJ5 0,8-4h6h 4,48 9,8 8,3 8,4 3 3,4 0,5 0,3 9 0,12 0,25 060 MJ6 1-4h6h 5,35 12 10,2 10,3 0,5 3,5 4,2 11 0,003 0,3 070 MJ7 1-4h6h 6,35 13,2 11,2 11,3 4 5,2 0,7 0,5 12 0,35 080 MJ8 1-4h6h 7,35 15,5 13,2 13,3 4,5 6,2 14 0,15 0,4 100 MJ10 1,25-4h6h 9,19

29、18,9 16 16,3 0,6 5 7,9 0,8 0,6 17 0,0025 0,5 120 MJ12 1,25-4h6h 11,19 21,1 18 18,3 6 9,8 0,9 19 0,18 0,6 a In accordance with ISO5855-2 0 0,3 0 0,3EN 3011:1998 BSI 04-1999 5 Table 2 Length code N 0,3 Thread code 050 060 070 080 100 120 W Mass a W Mass a W Mass a W Mass a W Mass a W Mass a max. min.

30、max. min. max. min. max. min. max. min. max. min. 008 8 2,76 010 10 3,02 2,7 2,2 4,86 6,69 9,75 012 12 2,1 1,7 3,28 5,23 7,22 10,45 014 14 3,54 5,60 7,74 11,15 17,88 25,66 016 16 3,80 5,96 2,7 2,2 8,26 2,7 2,2 11,85 18,97 27,14 018 18 4,06 6,33 8,78 12,54 20,06 28,61 020 20 4 2,5 4,32 6,70 9,30 13,2

31、4 3,3 2,7 21,15 30,09 022 22 6 4,5 4,58 4 2,5 7,07 9,82 13,94 22,23 3,4 2,8 31,56 024 24 8 6,5 4,84 6 4,5 7,44 4 2,5 10,34 14,64 23,32 33,04 026 26 10 8,5 5,10 8 6,5 7,81 6 4,5 10,86 4 2,5 15,33 24,41 34,51 028 28 12 10,5 5,35 10 8,5 8,18 8 6,5 11,38 6 4,5 16,03 25,50 35,98 030 30 14 12,5 5,61 12 10

32、,5 8,55 10 8,5 11,90 8 6,5 16,73 4 2,7 26,59 37,46 032 32 16 14,5 5,87 14 12,5 8,92 12 10,5 12,42 10 8,5 17,43 6 4,5 27,68 38,93 034 34 18 16,5 6,13 16 14,5 9,29 14 12,5 12,94 12 10,5 18,12 8 6,5 28,76 4 2,8 40,4 036 36 20 18,5 6,39 18 16,5 9,66 16 14,5 13,46 14 12,5 18,82 10 8,5 29,85 6 4,5 42,1 03

33、8 38 22 20,5 6,65 20 18,5 10,03 18 16,5 13,98 16 14,5 19,52 12 10,5 30,94 8 6,5 43,7 040 40 24 22,5 6,91 22 20,5 10,40 20 18,5 14,51 18 16,5 20,22 14 12,5 32,03 10 8,5 45,4 042 42 26 24,5 7,17 24 22,5 10,77 22 20,5 15,03 20 18,5 20,91 16 14,5 33,12 12 10,5 47,0 044 44 28 26,5 7,43 26 24,5 11,14 24 2

34、2,5 15,55 22 20,5 21,61 18 16,5 34,20 14 12,5 48,7 046 46 30 28,5 7,69 28 26,5 11,51 26 24,5 16,07 24 22,5 22,31 20 18,5 35,29 16 14,5 50,3 048 48 32 30,5 7,95 30 28,5 11,88 28 26,5 16,59 26 24,5 23,01 22 20,5 36,38 18 16,5 52,0 050 50 34 32,5 8,21 32 30,5 12,25 30 28,5 17,11 28 26,5 23,71 24 22,5 3

35、7,47 20 18,5 53,6 052 52 36 34,5 8,46 34 32,5 12,62 32 30,5 17,63 30 28,5 24,40 26 24,5 38,56 22 20,5 55,3 054 54 38 36,5 8,72 36 34,5 12,99 34 32,5 18,15 32 30,5 25,10 28 26,5 39,65 24 22,5 56,9 056 56 40 38,5 8,98 38 36,5 13,36 36 34,5 18,67 34 32,5 25,80 30 28,5 40,73 26 24,5 58,6 058 58 42 40,5

36、9,24 40 38,5 13,73 38 36,5 19,19 36 34,5 26,50 32 30,5 41,82 28 26,5 60,3 060 60 44 42,5 9,50 42 40,5 14,10 40 38,5 19,71 38 36,5 27,19 34 32,5 42,91 30 28,5 61,9 062 62 46 44,5 9,76 44 42,5 13,47 42 40,5 20,23 40 38,5 27,89 36 34,5 44,00 32 30,5 63,6 064 64 48 46,5 10,02 46 44,5 14,84 44 42,5 20,75

37、 42 40,5 28,59 38 36,5 45,09 34 32,5 65,2 066 66 50 48,5 10,28 48 46,5 15,21 46 44,5 21,27 44 42,5 29,29 40 38,5 46,18 36 34,5 86,9 068 68 52 50,5 10,54 50 48,5 15,57 48 46,5 21,80 46 44,5 29,98 42 40,5 47,26 38 36,5 68,5EN 3011:1998 6 BSI 04-1999Table 2 Length code N 0,3 Thread code 050 060 070 080

38、 100 120 W Mass a W Mass a W Mass a W Mass a W Mass a W Mass a max. min. max. min. max. min. max. min. max. min. max. min. 070 70 54 52,5 10,80 52 50,5 15,94 50 48,5 22,32 48 46,5 30,68 44 42,5 48,35 40 38,5 70,2 072 72 54 52,5 16,31 52 50,5 22,84 50 48,5 31,38 46 44,5 49,44 42 40,5 71,8 074 74 56 5

39、4,5 16,68 54 52,5 23,26 52 50,5 32,08 48 46,5 50,53 44 42,5 73,5 076 76 58 56,5 17,05 56 54,5 23,88 54 52,5 32,77 50 48,5 51,62 46 44,5 75,2 078 78 60 58,5 17,42 58 56,5 24,40 56 54,5 33,47 52 50,5 52,71 48 46,5 76,8 080 80 62 60,5 17,79 60 58,5 24,92 58 56,5 34,17 54 52,5 53,79 50 48,5 78,5 082 82

40、64 62,5 18,16 62 60,5 25,44 60 58,5 34,87 56 54,5 54,88 52 50,5 80,1 084 84 66 64,5 18,53 64 62,5 25,96 62 60,5 35,56 58 56,5 55,97 54 52,5 81,8 086 86 66 64,5 26,48 64 62,5 36,26 60 58,5 57,06 56 54,5 83,4 088 88 68 66,5 27,00 66 64,5 36,96 62 60,5 58,15 58 56,5 85,1 090 90 70 68,5 27,52 68 66,5 37

41、,66 64 62,5 59,23 60 58,5 86,7 092 92 72 70,5 28,04 70 68,5 38,36 66 64,5 60,32 62 60,5 88,4 094 94 74 72,5 28,56 72 70,5 39,05 68 66,5 61,41 64 62,5 90,0 096 96 76 74,5 29,09 74 72,5 39,75 70 68,5 62,50 66 64,5 91,7 098 98 78 76,5 29,61 76 74,5 40,45 72 70,5 63,59 68 66,5 93,4 100 100 78 76,5 41,15

42、 74 72,5 64,68 70 68,5 95,0 104 104 82 80,5 42,54 78 76,5 66,85 74 72,5 98,3 108 108 86 84,5 43,94 82 80,5 69,03 78 76,5 101,6 112 112 90 88,5 45,33 86 84,5 71,21 82 80,5 104,9 116 116 90 88,5 73,38 86 84,5 108,3 120 120 94 92,5 75,56 90 88,5 111,6 124 124 98 96,5 77,74 94 92,5 114,9 128 128 102 100

43、,5 79,91 98 96,5 118,2 132 132 106 104,5 82,09 102 100,5 121,4 136 136 110 108,5 84,26 106 104,5 124,7 140 140 114 112,5 86,44 110 108,5 128,1 144 144 114 112,5 131,5 148 148 118 116,5 134,7 152 152 122 120,5 138,0 156 156 126 124,5 141,4 160 160 130 128,5 144,7 164 164 134 132,5 148,0 168 168 138 1

44、36,5 151,2 a Mass quoted in kg/1000 partsEN3011:1998 BSI 04-1999 7 4 Designation EXAMPLE: NOTEIf necessary, the codeI9005 shall be placed between the description block and the identity block. 5 Marking EN2424, style A, as indicated onFigure 1. 6 Technical specification EN2582BS EN 3011:1998 BSI 389

45、Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated

46、by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStand

47、ard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest edition

48、s of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have be

49、en published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to da