BS EN 3027-1994 Test method for dry film lubricants - Salt spray test《干膜润滑剂的试验方法 盐雾试验》.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS EN 3027:1994 Test method for dry film lubricants Salt spray test The European Standard EN3027:1994 has the status of a BritishStandard UDC 621.892:620.193.272:669.14:629.7BSEN3027:1994 This BritishStandard, having been prepared under the directionof the Aerospace

2、 Standards Policy Committee, waspublished under the authorityof the Standards Boardand comes into effect on 15April1994 BSI01-2000 The following BSI references relate to the work on this standard: Committee reference ACE/44 Draft for comment90/75757 DC ISBN 0 580 22402 3 Cooperating organizations Th

3、e European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalisation Denmark Dansk Standardiseringsraa

4、d Finland Suomen Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland Ireland National Standards Authority of Ireland Italy Ente Nazionale Italian

5、o di Unificazione Luxembourg Inspection du Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Asociacin Espaola de Normalizacin y Certificacin Sweden Standardiseringskommissionen i Sverige Switzerlan

6、d Association suisse de normalisation United Kingdom British Standards Institution Amendments issued since publication Amd. No. Date CommentsBSEN3027:1994 BSI 01-2000 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 Text of EN3027 3 National annex NA (info

7、rmative) Committees responsible Inside back cover National annex NB (informative) Cross-references Inside back coverBSEN3027:1994 ii BSI 01-2000 National foreword This BritishStandard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language versio

8、n of EN3027:1994 Aerospace series Test method for dry-film lubricants. Salt spray test, published by the European Committee for Standardization (CEN). EN3027 was produced as a result of international discussion in which the UnitedKingdom took an active part. A British Standard does not purport to in

9、clude all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pag

10、esi andii, theEN title page, pages2 to4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN30

11、27:1994 January1994 UDC 621.892:620.193.272:669.14:629.7 Descriptors: Aircraft industry, lubricants, solids, films, corrosion tests, salt spray tests English version Aerospace series Test method for dry film lubricants Salt spray test Srie arospatiale Mthode dessai pour films lubrifiants solides Ess

12、ai au brouillard salin Luft- und Raumfahrt Prfverfahren fr Trockenschmiermittelfilme Salzsprhnebelprfung This European Standard was approved by CEN on1994-01-06. CEN members are bound to comply with the CEN Internal Regulations which stipulate the conditions for giving this European Standard the sta

13、tus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A

14、version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany,

15、 Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1994 Copyright

16、 reserved to CEN members Ref.No.EN3027:1994EEN3027:1994 BSI 01-2000 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has successive

17、ly received the approval of the National Association and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This standard was submitted for Formal Vote, and the result was positive. This European Standard shall be given the status ofa national standard, either

18、by publication of anidentical text or by endorsement, at the latest by July1994, and conflicting national standards shall be withdrawn at the latest by July1994. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium

19、, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Specimens and test equipment 3 4 Procedure 3 5 Expression of results 3 6 Test rep

20、ort 3EN3027:1994 BSI 01-2000 3 1 Scope This standard specifies a test method to verify that dry film lubricants ensure the required corrosion protection after exposure to salt spray. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publi

21、cations. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revisio

22、n. For undated references the latest edition of the publication referred to applies. ISO9227, Corrosion tests in artificial atmospheres Salt spray tests. EN2491, Aerospace series Molybdenum disulphide dry film lubricants applied to fasteners 1) . EN2793, Aerospace series Phosphate treatment of ferro

23、us alloys 1) . EN3021, Aerospace series Molybdenum disulphide dry lubricants to be applied as a film Technical specification 1) . EN3032, Aerospace series Test method for dry film lubricants Thickness measurement. 3 Specimens and test equipment Three specimens in0,18% (nominal) carbon steel of about

24、75mm 150mm 3mm. An apparatus suitable for the measurement of the coating thickness and a salt spray chamber to ISO9227. 4 Procedure Degrease the specimens and dry abrasive blast both surfaces and edges of the specimens with clean dry alumina of1254m grain size. Phosphate the specimens according to E

25、N2793:zinc phosphate to a mass per unit area ofnot less than7g/m 2or manganese phosphate to amass per unit area of not less than4g/m 2 . Measure the thickness of the specimen taking care not to damage the phosphating. Apply the dry lubricant to the surfaces and edges in accordance with EN2491. After

26、 curing, to avoid the edge effect, seal the edges on10mm width with a suitable sealing compound. Verify according to EN3032 that the thickness meets the requirements of EN3021. Test the specimens according to ISO9227. After an exposure for96h, remove them and rinse them in deionized water to remove

27、salt residues. 5 Expression of results Examine the specimens visually, note the number and size of any rust spots and the number of blisters on each specimen. 6 Test report It shall include the following: reference to this standard; film designation to EN3021; application method to EN2491; curing co

28、nditions; visual inspection results. 1) In preparation at the date of publication of this standard4 blankBSEN3027:1994 BSI 01-2000 National annex NA (informative) Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the Aerospace Stand

29、ards Policy Committee (ACE/-) to Technical Committee ACE/44 upon which the following bodies were represented: Aluminium Finishing Association Metal Finishing Association Ministry of Defence National Centre of Tribology Oil and Colour Chemists Association Paintmakers Association of Great Britain Ltd.

30、 Society of British Aerospace Companies Limited National annex NB (informative) Cross-references The BritishStandards corresponding to the European Standards referred to in the text are identical in number and title with those given in clause2, with the exception of EN2491, EN2793 and EN3021 for whi

31、ch no corresponding BritishStandards exist.BS EN 3027:1994 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is inc

32、orporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyo

33、ne finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS whic

34、h ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it i

35、s BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters

36、 Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts

37、 on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bo

38、dies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the fre

39、e use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.