BS EN 303-1-2017 Heating boilers Heating boilers with forced draught burners Terminology general requirements testing and marking《供暖锅炉 带强制通风燃烧器的供暖锅炉 术语、一般要求、试验和标记》.pdf

1、Heating boilersPart 1: Heating boilers with forced draught burners - Terminology, general requirements, testing and markingBS EN 303-1:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEANSTANDARDNORME EUROPENNE EUROPISCHE NORMEN 303-1September 2017ICS 91.140.

2、10 Supersedes EN 15034:2006, EN 303-1:1999EnglishVersionHeating boilers - Part 1: Heating boilers with forced draught burners - Terminology, general requirements, testing and marking Chaudires de chauffage - Partie 1 : Chaudiresavecbrleurs air souffl - Terminologie, prescriptionsgnrales, essais et m

3、arquage Heizkessel - Teil 1: Heizkesselmit Geblsebrennern -Begriffe, Allgemeine Anforderungen, Prfung undKennzeichnung This European Standard was approved by CEN on 26 June 2017.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving thisEu

4、ropean Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical referencesconcerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official version

5、s (English, French, German). A version in any other language made bytranslation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC ManagementCentre has the same status as the officialversions.CEN members are the nationalstandards bodies of Austria, Belgium

6、, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, S

7、witzerland, Turkey and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reservedworldwide for CENnational

8、Members.Ref. No. EN 303-1:2017 ENational forewordThis British Standard is the UK implementation of EN 303-1:2017. It supersedes BS EN 303-1:1999, which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee RHE/10, Heating boilers.A list of organizations represent

9、ed on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 93

10、472 8ICS 01.040.91; 91.140.10Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2017.Amendments/corrigenda issued since publicationDate Text affectedBR

11、ITISH STANDARDBS EN 3031:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 303-1 September 2017 ICS 91.140.10 Supersedes EN 15034:2006, EN 303-1:1999English Version Heating boilers - Part 1: Heating boilers with forced draught burners - Terminology, general requirements, testing and marking C

12、haudires de chauffage - Partie 1 : Chaudires avec brleurs air souffl - Terminologie, prescriptions gnrales, essais et marquage Heizkessel - Teil 1: Heizkessel mit Geblsebrennern - Begriffe, Allgemeine Anforderungen, Prfung und Kennzeichnung This European Standard was approved by CEN on 26 June 2017.

13、 CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on

14、application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELE

15、C Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

16、 Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre

17、: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 303-1:2017 EBS EN 3031:2017EN 303-1:2017 (E) 2 Contents Page European foreword . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions,

18、 units and symbols . 7 3.1 Terms and definitions . 7 3.2 Units and symbols 10 3.2.1 Units 10 3.2.2 Symbols 11 4 Requirements 11 4.1 Construction requirements 11 4.1.1 General requirements 11 4.1.2 Specific requirements . 23 4.2 Operational requirements 25 4.2.1 General . 25 4.2.2 Verification of the

19、 nominal condensing output 25 4.2.3 Formation of condensation 25 4.2.4 Temperature of combustion products . 25 4.2.5 Surface temperature . 25 4.2.6 Water side resistance of the boiler 26 4.2.7 Soundness of the boiler 26 4.2.8 Temperature sensing control type TR and temperature sensing control type S

20、TB 26 4.3 Electrical equipment . 26 4.3.1 Electrical safety . 26 4.3.2 Electromagnetic compatibility 27 5 Tests 27 5.1 General . 27 5.2 Boilers of steel or non-ferrous metal 27 5.2.1 Tests to be carried out before production 27 5.2.2 Factory production control (FPC) for steel boilers 27 5.3 Boilers

21、of cast iron or non-ferrous metals 28 5.3.1 Test to be carried out before production 28 5.3.2 Test during production 28 5.4 Test for gas soundness . 29 5.5 Water side resistance measurement 29 5.5.1 General . 29 5.5.2 Test rig for the establishment of the water side resistance . 29 5.6 Additional te

22、sts for low temperatures boilers 31 5.6.1 Additional tests by using of corrosion resistant coatings . 31 5.6.2 Additional tests for oil-fired low temperatures boilers . 31 6 Marking 31 6.1 Information on the boiler data plate . 31 6.2 Requirements of the data plate . 31 7 Technical documentation, sc

23、ope of supply . 31 7.1 General . 31 BS EN 3031:2017EN 303-1:2017 (E) 3 7.2 Technical information (product fiche) and installation instructions . 31 7.3 Operating instructions 33 7.4 Label 33 Annex A (informative) Conformity evaluation 34 Annex ZA (informative) Relationship between this European Stan

24、dard and the ecodesign requirements of Commission Regulation (EU) No 813/2013 aimed to be covered 35 Annex ZB (informative) Relationship between this European Standard and the ecodesign requirements of Commission Regulation (EU) No 811/2013 aimed to be covered 36 Bibliography . 37 BS EN 3031:2017EN

25、303-1:2017 (E) 4 European foreword This document (EN 303-1:2017) has been prepared by Technical Committee CEN/TC 57 “Central heating boilers”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text

26、or by endorsement, at the latest by March 2018, and conflicting national standards shall be withdrawn at the latest by March 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying a

27、ny or all such patent rights. This document has been prepared under a mandate M/534 and M/535 given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA and A

28、nnex ZB, which are integral parts of this document. This document supersedes EN 303-1:1999 and EN 15034:2006. The following essential changes have been made: a) Construction requirements were adopted from EN 15034; b) Terminology of EU-Regulations 811/2013 and 813/2013 adopted; c) the document was c

29、ompletely revised technically; d) the document was completely revised editorially. The following structure is intended for the European Standards for heating boilers: EN 303-1, Heating boilers Part 1: Heating boilers with forced draught burners Terminology, general requirements, testing and marking

30、EN 303-2, Heating boilers Part 2: Heating boilers with forced draught burners Special requirements for boilers with atomizing oil burners EN 303-3, Heating boilers Part 3: Gas fired central heating boilers Assembly comprising a boiler body and a forced draught burner EN 303-4, Heating boilers Part 4

31、: Heating boilers with forced draught burners Special requirements for boilers with forced draught oil burners with outputs up to 70 kW and a maximum operating pressure of 3 bar Terminology, special requirements, testing and marking EN 303-5, Heating boilers Part 5: Heating boilers for solid fuels,

32、hand and automatically fired, with a nominal heat output of up to 300 kW Terminology, requirements, testing and marking EN 304, Heating boilers Test code for heating boilers for atomizing oil burners According to the CEN-CENELEC Internal Regulations, the national standards organisations of the follo

33、wing countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, N

34、orway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 3031:2017EN 303-1:2017 (E) 5 1 Scope This European Standard applies to boilers used for central heating (heating boilers) with forced draught burners with a nominal heat out

35、put not exceeding 1 000 kW, which are operated either with negative pressure (natural draught boilers) or with positive pressure (pressurized boiler) in the combustion chamber, in accordance with the boiler instructions. This European Standard specifies the necessary terminology, the requirements on

36、 the materials and testing of them, and marking requirements for heating boilers. Particular requirements for boilers that can be used with open vented systems are contained in EN 303-4. The requirements of this standard apply to heating boilers that are tested on an authorized test rig. Boilers in

37、accordance with this standard are designed for the heating of central heating installations in which the heat carrier is water, and the maximum allowable operating temperature of which is restricted to 100 C. The maximum allowable operating pressure is 8 bar. For boilers and water heaters (storage o

38、r continuous flow heater) this standard only applies to the parts which are necessarily subject to the operating conditions of the heating boiler (heating part). This standard does not apply to gas boilers with atmospheric burners, boilers for solid fuels, boilers with oil vaporization burners. For

39、these boilers there are further requirements. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition o

40、f the referenced document (including any amendments) applies. EN 226:1987, Atomizing oil burners - Connecting dimensions between burners and heat generators EN 303-2:2017, Heating boilers - Part 2: Heating boilers with forced draught burners - Special requirements for boilers with atomizing oil burn

41、ers EN 303-4:1999, Heating boilers - Part 4: Heating boilers with forced draught burners - Special requirements for boilers with forced draught oil burners with outputs up to 70 kW and a maximum operating pressure of 3 bar - Terminology, special requirements, testing and marking EN 304:2017, Heating

42、 boilers - Test code for heating boilers for atomizing oil burners EN 10025-2:2004, Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels EN 10027-2:2015, Designation systems for steels - Part 2: Numerical system EN 10028-2:2017, Flat produc

43、ts made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties EN 10028-3:2017, Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized EN 10029:2010, Hot-rolled steel plates 3 mm thick or above

44、- Tolerances on dimensions and shape EN 10088-2:2014, Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes BS EN 3031:2017EN 303-1:2017 (E) 6 EN 10204:2004, Metallic products - Types of inspection documents EN 13501-1:2

45、007+A1:2009, Fire classification of construction products and building elements - Part 1: Classification using data from reaction to fire tests EN 14597:2012, Temperature control devices and temperature limiters for heat generating systems EN 60335-1:2012, Safety of household and similar electrical

46、appliances Part 1: General requirements (IEC 60335-1:2010) EN 60529:1991, Degrees of protection provided by enclosures (IP Code) (IEC 60529:1989) EN 60730-1:2011, Automatic electrical controls for household and similar use - Part 1: General requirements (IEC 60730:2010), modified EN 60730-2-9:2010,

47、Automatic electrical controls for household and similar use - Part 2-9: Particular requirements for temperature sensing controls (IEC 60730-2-9:2008), modified EN 61000-6-2:2005, Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity for industrial environments (IEC 61000-6-2:2

48、005) EN 61000-6-3:2007, Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments (IEC 61000-6-3:2006) EN 60335-2-102:2016, Household and similar electrical appliances - Safety - Part 2-102: Particular requirem

49、ents for gas, oil and solid-fuel burning appliances having electrical connections (IEC 60335-2-102:2004, modified + A1:2008, modified + A2:2012, modified) EN ISO 4063:2010, Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009) EN ISO 6506 (all parts), Metallic materials - Brinell hardness test EN ISO 9606-1:2013, Qualification testing of welders - Fusion welding - Part 1: Steels (ISO 9606-1:2012 including Cor 1:2012) EN ISO 9606-2:2004, Qualification test of welders -