BS EN 3149-1997 Shank nuts - Installation holes 60 swage flanges - Design standard《杆螺母 60型锻法兰安装孔 设计标准》.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS EN 3149:1997 Shank nuts Installation holes, 60 swage, flanges Design standard The European Standard EN 3149:1996 has the status of a British Standard ICS 49.030.30BSEN3149:1997 This British Standard, having been prepared under the direction of the Engineering Sec

2、tor Board, was published under the authority of the Standards Board and comes into effect on 15 January 1997 BSI 11-1998 The following BSI references relate to the work on this standard: Committee reference ACE/12 Draft for comment 88/71828 DC ISBN 0 580 26901 9 Committees responsible for this Briti

3、sh Standard The preparation of this British Standard was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems, upon which the following bodies were represented: Association of Electronic, Telecommunications and Business Equipment Industries British Industrial Fasteners

4、Federation Ministry of Defence Society of British Aerospace Companies Amendments issued since publication Amd. No. Date CommentsBSEN3149:1997 BSI 11-1998 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 1 Scope 3 2 Normative references 3 3 Design 3 4 Use 3 5

5、Required characteristics 4 6 Tolerances 7 7 Assembly 7 8 Designation of installation hole 7 9 Drawing presentation 8 Figure 1 3 Figure 2 4 Figure 3 5 Figure 4 6 Figure 5 6 Figure 6 6 Figure 7 7 Figure 8 8 Figure 9 8 Table 1 4 Table 2 5BSEN3149:1997 ii BSI 11-1998 National foreword This British Stand

6、ard has been prepared by Technical Committee ACE/12 and is the English language version of EN 3149:1996 Aerospace series Shank nuts Installation holes, 60 swage, flanges Design standard, published by the European Committee for Standardization (CEN). EN 3149:1996 was produced as a result of internati

7、onal discussions in which the United Kingdom took an active part. There are no British Standards corresponding to the European Standards referred to in the text. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for

8、their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 8 and a back cover. This standard has been updated (see

9、 copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3149 August 1996 ICS 49.040.20 Descriptors: Aircraft industry, nut, fastener, installation, design, utilization, hole

10、 size, dimensional tolerance, designation English version Aerospace series Shank nuts Installation holes, 60 swage, flanges Design standard Srie arospatiale Ecrous sertir Trous d installation, sertissage 60, brides Norme de conception Luft- und Raumfahrt Einnietmuttern Einbaulcher, 60 Aufweitung, Fl

11、ansche Konstruktionsnorm This European Standard was approved by CEN on 1996-06-29. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and

12、 bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibili

13、ty of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portu

14、gal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members Ref. No. EN 3149:1996 EEN3149:1996 BSI 11-1998

15、2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services o

16、f the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 1997, and conflicting national standards shall be withdrawn at the lates

17、t by February 1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway,

18、 Portugal, Spain, Sweden, Switzerland and the United Kingdom.EN3149:1996 BSI 11-1998 3 1 Scope This standard specifies the dimensions of installation holes for EN-standardized 60 swage shank nuts and the relevant functional dimensions of the component flange, for aerospace applications. 2 Normative

19、references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of

20、 these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 3148, Aerospace series Shank nuts, self-locking, flange restrained Installation procedure 1) . 3 Design See

21、Figure 1. 4 Use Shank nuts are parts which are secured axially by swaging an extended shank into a countersink. The dimensions and the 60 countersink ensure that the expansion of the shank after swaging is between 10 % and 20 %, which provides adequate safety without excessive expansion. Shank nuts

22、are prevented from turning by an abutment in the component flange on one side. Due to the small abutment face of the nut, care shall be taken that the strength of the component flange is suited to the surface pressure of the shank nut during tightening of the bolt. It is recommended that the designe

23、r selects the thickness of the component flange on the basis of the minimum structural requirements, taking into consideration dimension “A” in Table 2. Shank nuts are used for bolted joints which are only accessible from one side and where bihexagonal head nuts cannot be used. The use of shank nuts

24、 in highly stressed components is not recommended since the size of the corner radius of the abutment shoulder is small and could have stress increasing characteristics. 1) Published as AECMA Prestandard at the date of publication of this standard Figure 1EN3149:1996 4 BSI 11-1998 5 Required charact

25、eristics Dimensions and tolerances in millimetres 5.1 Installation hole See Figure 2 and Table 1. Table 1 Figure 2 Nut thread B C D F Diameter code Designation min. 050 MJ50,8-4H6H 6,5 7,2 0,8 7,8 060 MJ61-4H5H 7,5 8,2 8,8 070 MJ71-4H5H 8,5 9,2 1,55 10 080 MJ81-4H5H 9,5 10,2 1,8 11,5 + 0,1 0 + 0,4 0

26、 + 0,2 0EN3149:1996 BSI 11-1998 5 5.2 Flange and abutment shoulder See Figure 3 and Table 2. Table 2 Figure 3 Nut thread A K M M 1 N R Nut dimensions Diameter code Designation min. min. 0,1 E max. a S max. a 050 MJ50,8-4H6H 2 5 See 5.2.2 See 5.2.3 2,7 1 13,25 9,6 060 MJ61-4H5H 5,5 14,25 10,6 070 MJ7

27、1-4H5H 3 6 16,25 11,6 080 MJ81-4H5H 3,5 6,5 17,25 12,6 a See the relevant product standard. + 0,2 0EN3149:1996 6 BSI 11-1998 5.2.1 Shank nuts installed on a straight line See Figure 4 and Table 2. 5.2.2 Diameter M of abutment shoulder smaller than pitch circle diameter G See Figure 5 and Table 2. 5.

28、2.3 Diameter M 1of abutment shoulder greater than pitch circle diameter G See Figure 6 and Table 2. Figure 4 Figure 5 Figure 6EN3149:1996 BSI 11-1998 7 6 Tolerances The run-out tolerances of M or M 1and the positional tolerance of B shall be derived from Figure 7. The recommended tolerances are: 7 A

29、ssembly EN 3148 8 Designation of installation hole EXAMPLE: Run-out tolerance of M or M 1 : 0,1 Positional tolerance of B: 0,2 Figure 7EN3149:1996 8 BSI 11-1998 9 Drawing presentation 9.1 Installation hole EXAMPLE: see Figure 8. Alternatively, the hole may be fully dimensioned on the drawing. 9.2 In

30、stalled nut EXAMPLE: see Figure 9. Figure 8 Figure 99 blankBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

31、| | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions Brit

32、ish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity wh

33、ile using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automa

34、tically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the

35、BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI elec

36、tronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase pri

37、ce of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except a

38、s permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the

39、course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.