BS EN 3155-004-2007 Aerospace series - Electrical contacts used in elements of connection - Contacts electrical male type A crimp class T Product standard《航空航天系列 连接部件用电触点 T级、卷边、A型、.pdf

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58connection Part 004: Contacts, electrical, male, type A, crimp, class T Product standardThe Europea

2、n Standard EN 3155-004:2007 has the status of a British StandardICS 49.060Aerospace series Electrical contacts used in elements of BRITISH STANDARDBS EN 3155-004:2007BS EN 3155-004:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April

3、2007 BSI 2007ISBN 978 0 580 50571 3Amendments issued since publicationAmd. No. Date CommentsThis publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal

4、obligations.National forewordThis British Standard was published by BSI. It is the UK implementation of EN 3155-004:2007.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Panel ACE/6/-/3, Aerospace Connecto

5、rs.A list of organizations represented on this committee can be obtained on request to its secretary.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 3155-004March 2007ICS 49.060English VersionAerospace series - Electrical contacts used in elements ofconnection - Part 004: Contacts, electrical, mal

6、e, type A, crimp,class T - Product standardSrie arospatiale - Contacts lectriques utiliss dans lesorganes de connexion - Partie 004 : Contacts lectriques,mles, type A, sertir, classe T - Norme de produitLuft- und Raumfahrt - Elektrische Kontakte zur Verwendungin Verbindungselementen - Teil 004: Elek

7、trischeStiftkontakte, Typ A, crimpbar, Klasse T - ProduktnormThis European Standard was approved by CEN on 6 January 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard withou

8、t any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language mad

9、e by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France,

10、Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNG

11、Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3155-004:2007: E2 Contents Page Foreword3 0 Introduction4 1 Scope 4 2 Normative references 4 3 Definitions 5 4 Required chara

12、cteristics.5 4.1 Specific characteristics.5 4.2 Dimensions and mass.5 4.3 Marking by colour code 6 4.4 Material, surface treatment.7 4.5 Permissible cables.7 4.6 Tooling7 4.6.1 Crimping tools7 4.6.2 Insertion/extraction tools8 4.7 Cable stripping.9 4.8 Tests9 4.9 Gauges10 5 Designation 10 6 Marking

13、.10 7 Technical specification .10 EN 3155-004:20073 Foreword This document (EN 3155-004:2007) has been prepared by the AeroSpace and Defense Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Sta

14、ndard has re-ceived the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the late

15、st by September 2007, and conflicting national standards shall be with-drawn at the latest by September 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or

16、all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Repub-lic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,

17、Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3155-004:20074 0 Introduction The contacts defined by this standard are derived from those of MIL-C-39029/4 and, in

18、termateable with those of MIL-C-39029/5. They are specified as a 260 C class instead of a 200 C class as detailed in the MIL stan-dard. 1 Scope This standard specifies the required characteristics, tests and tooling applicable to male electrical con-tacts 004, type A, crimp, class T, used in element

19、s of connection according to EN 3155-002. It shall be used together with EN 3155-001. The associated female contacts are defined in EN 3155-005. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refer-ences, only the edition c

20、ited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 8843, Aircraft Crimp-removable contacts for electrical connectors Identification system EN 2083; Aerospace series Copper or copper alloy conductors for electrical cables Produc

21、t standard EN 2591 (series), Aerospace series Elements of electrical and optical connection Test methods EN 3155-001, Aerospace series Electrical contacts used in elements of connection Part 001: Technical specification EN 3155-002, Aerospace series Electrical contacts used in elements of connection

22、 Part 002: List and utilization of contacts EN 3155-005, Aerospace series Electrical contacts used in elements of connection Part 005: Contacts, electrical, female, type A, crimp, class T Product standard MIL-DTL-22520, Crimping tools, terminal, hand or power actuated, wire termination, and tool kit

23、s, general specification for1)MIL-C-22520/1, Crimping tools, terminal, hand, wire termination for wire barrel sizes 12 through 201)MIL-C-22520/2, Crimping tools, terminal, hand, wire termination for wire barrel sizes 20 through 281)MIL-C-22520/7, Crimping tools, terminal, hand, wire termination for

24、wire barrel sizes 16, 20 and 221) MIL-C-39029/4, Contacts, electrical connector, pin, crimp removable, (for MIL-C-26482 series 2, MIL-C-81703 series 3, MIL-C-83723 series I and III, and MIL-C-83733 connectors)1)MIL-C-39029/5, Contacts, electrical connector, socket, crimp removable, (for MIL-C-26482

25、series 2, MIL-C-81703 series 3, MIL-C-83723 series I and III, and MIL-C-83733 connectors and MIL-S-12883/40 and /41 relay sockets)1)MIL-I-81969/14, Installing and removal tools, connector electrical contact, type III, class 2, composition B1)MIL-I-81969/30, Installing and removal tools, connector el

26、ectrical contact, type II, class 2, composition C for unwired1)1) Published by: Department of Defense (DOD), the Pentagon, Washington D.C. 20301 USA EN 3155-004:20075 3 Definitions For the purposes of this standard, the definitions given in EN 3155-001 apply. 4 Required characteristics 4.1 Specific

27、characteristics Type A contacts are for general application and class T corresponds to an operating temperature range from 65 C to 150 C. 4.2 Dimensions and mass See Figures 1 and 2 and Table 1. Dimensions and tolerances are given in millimetres and apply after surface treatment. Key 1 White dot 2 C

28、olour bands, see Table 2 3 Flat S a P (one side only) bContact active area protection cApproximately spherical Figure 1 Key 1 Radii Figure 2 Barrel, contacts 16-18 and 12-12 EN 3155-004:20076 Table 1 Size A B C D E F G H Contact Barrel max. 13,94 4,34 3,30 0,84 1,98 1,04 1,27 20 20 18,29 13,79 4,06

29、3,17 0,74 1,93 0,99 1,22 13,94 4,34 3,30 0,84 1,98 1,04 1,35 20 18 18,29 13,79 4,06 3,17 0,74 1,93 0,99 1,30 14,33 6,53 3,30 1,22 2,62 1,61 1,73 16 16 20,85 14,17 6,25 3,17 1,12 2,56 1,56 1,68 14,33 6,53 3,30 1,22 2,62 1,61 1,95 16 14 20,85 14,17 6,25 3,17 1,12 2,56 1,56 1,90 14,33 6,53 3,30 1,22 2,

30、62 1,61 1,35 16 18 20,85 14,17 6,25 3,17 1,12 2,56 1,56 1,30 14,33 6,53 3,05 1,22 3,83 2,41 2,59 12 12 20,85 14,17 6,25 2,92 1,12 3,76 2,36 2,49 Size J K L M N P S T Mass g Contact Barrel max. 1,98 2,62 1,68 4,75 1,73 0,81 0,51 20 20 1,93 2,54 1,57 3,94 1,35 0,66 0,23 0,30 1,98 2,62 1,68 4,75 1,73 0

31、,81 0,51 20 18 1,93 2,54 1,57 3,94 1,35 0,66 0,23 0,30 2,62 3,38 2,26 7,21 2,16 1,07 0,81 16 16 2,56 3,30 2,11 6,35 1,73 0,91 0,43 0,65 2,62 3,38 2,26 7,21 2,16 1,07 0,81 16 14 2,56 3,30 2,11 6,35 1,73 0,91 0,43 0,65 1,98 3,38 1,68 7,21 2,16 1,07 0,81 2,62 16 18 1,93 3,30 1,57 6,35 1,73 0,91 0,43 2,

32、56 0,65 3,83 4,83 3,45 7,21 2,16 1,07 1,57 4,01 12 12 3,76 4,75 3,30 6,35 1,73 0,91 1,19 3,94 1,36 4.3 Marking by colour code See Table 2. Table 2 Two bands according to ISO 8843 Size Contact Barrel Band 1 Band 2 Dot 20 20 Red Red White 20 18 Red BrownaWhite 16 16 Blue Blue White 16 14 Blue WhitebWh

33、ite 16 18 Blue BrownaWhite12 12 Yellow Yellow White aViolet Colour band not to be used for new manufacture. bOrange colour band not to be used for new manufacture. Key 1 Dot 2 Band 1 3 Band 2 EN 3155-004:20077 4.4 Material, surface treatment Body material: copper alloy. Surface treatment: gold on ap

34、propriate undercoat in copper alloy. Thickness of protection not specified. Selective protection acceptable. 4.5 Permissible cables See Table 3. Table 3 Size Size of conductors Section Contact Barrel AECMA code mm2AWGaRated test current A 006 0,60 20 7,5 004 0,40 22 5,0 002 0,25 24 3,0 22 20 010 1,0

35、0 18 7,5 006 0,60 20 7,5 004 0,40 22 5,0 002 0,25 24 3,0 20 18 012 1,20 16 13,0 010 1,00 18 10,0 006 0,60 20 7,5 16 16 020 2,00 14 13,0 012 1,20 16 13,0 010 1,00 18 10,0 16 14 010 1,00 18 11,0 006 0,60 20 7,5 004 0,40 22 5,0 002 0,25 24 3,0 16 18 030 3,00 12 23,0 020 2,00 14 17,0 12 12 aAWG = Closes

36、t American Wire Gage 4.6 Tooling 4.6.1 Crimping tools Conform to MIL-DTL-22520, see Table 4. The qualification selector numbers used for crimping copper and copper alloy conductors in cables EN 2083 are indicated in Table 4. It is the responsibility of the user if the parameters in Table 4 are chang

37、ed for service use. EN 3155-004:20078 Table 4 Contact Cable size Tools M22520/1-01 Tools M22520/2-01 Tools M22520/7-01 Contact size Barrel size AECMA code AWGaPositioner Selectornumber Positioner Selectornumber Positioner Selectornumber 002 24 2 5 4 004 22 3 6 5 006 20 4 7 6 20 20 M22520/1-02Red M22

38、520/2-02 M22520/7-02 002 24 2 5 4 004 22 3 6 5 006 20 4 7 6 20 18 010 18 M22520/1-02Red 5 M22520/2-028 M22520/7-02 7 006 20 4 5 010 18 5 6 012 16 6 7 16 16 M22520/1-02 Blue Not applicable M22520/7-03 010 18 5 6 012 16 6 7 020 14 6 7 16 14 M22520/1-02 Blue Not applicable M22520/7-03 002 24 2 4 004 22

39、 3 5 006 20 4 6 16 18 010 18 M22520/1-02 Blue 5 Not applicable M22520/7-03 7 020 14 030 12 12 12 M22520/1-02 Yellow Not applicable Not applicable aAWG = Closest American Wire Gage 4.6.2 Insertion/extraction tools Conform to MIL-I-81969. See Table 5. Table 5 Size Extraction tools Contact Barrel Inser

40、tion tools Wired Contact Unwired Contact 20 20 M81969/14-11 M81969/14-11 M81969/30-05 20 18 M81969/14-11 M81969/14-11 M81969/30-05 16 16 M81969/14-03 M81969/14-03 M81969/30-06 16 14 M81969/14-03 M81969/14-03 M81969/30-06 16 18 M81969/14-03 M81969/14-04 M81969/30-06 12 14 M81969/14-04 M81969/14-04 M8

41、1969/30-07 EN 3155-004:20079 4.7 Cable stripping See Table 6. Table 6 Stripped length of cable Size mm Contact Barrel 0,5 20 20 20 18 4,5 16 16 16 14 16 18 12 12 6,8 4.8 Tests See Table 7. Table 7 Applicable EN 2591- Test Not applicableAccording to EN 3155-001 Remarks 101 Visual examination X 102 Ex

42、amination of dimensions and mass 201 Contact resistance low level X 202 Contact resistance at rated current X 204 Discontinuity of contacts in the microsecond range 210 Electrical overload X 220 Contact/conductor joint ageing by current and temperature cycling X 301 Endurance at temperature X T = (1

43、50 2) C Duration: 1 000 h 305 Rapid change of temperature X TA= ( 65 2) C TB(150 2) C 307 Salt mist X 315 Fluid resistance X 319 Gas-tightness of solderless wrapped connec-tions 402 Shock X 403 Sinusoidal and random vibrations At 260 C temperature 406 Mechanical endurance X 415 Test probe damage (fe

44、male contact) X 416 Contact bending strength X 417 Tensile strength (crimped connection) 418 Gauge insertion and extraction forces in and out of a female contact X 424 Stripping force, solderless wrapped connections X EN 3155-004:200710 Table 7 (concluded) Applicable EN 2591- Test Not applicableAcco

45、rding to EN 3155-001 Remarks 425 Unwrapping, solderless wrapped connections X 501 Soft soldering 502 Restricted entry X 503 Contact deformation after crimping X 507 Plating porosity 508 Measurement of thickness of coating on contacts X The measured thick-ness shall be recorded. 509 Adhesion of coati

46、ng on contacts X 513 Magnetic permeability 514 Solderability of contacts with self-contained sol-der and flux X 4.9 Gauges Not applicable. 5 Designation EXAMPLE Description block Identity block CONTACT, ELECTRICAL EN3155-004 M 20 20 Number of this standard Type of contact: M: male Contact size (see

47、Table 1) Barrel size (see Table 1) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 6 Marking See EN 3155-001. Colour code: see Table 1. 7 Technical specification See EN 3155-001. EN 3155-004:2007blankBS EN BSI389 Chiswick High RoadLondonW4 4AL3

48、155-004:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or rev

49、ision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identi