BS EN 3155-053-2007 Aerospace series - Electrical contacts used in elements of connection - Contacts electrical female 053 type A crimp class S Product standard《航空航天系列 连接部件用电触点 S级、.pdf

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58connection Part 053: Contacts, electrical, female 053, type A, crimp, class S Product standardThe E

2、uropean Standard EN 3155-053:2007 has the status of a British StandardICS 49.060Aerospace series Electrical contacts used in elements of BRITISH STANDARDBS EN 3155-053:2007BS EN 3155-053:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30

3、April 2007 BSI 2007ISBN 978 0 580 50617 8Amendments issued since publicationAmd. No. Date CommentsThis publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from

4、legal obligations.National forewordThis British Standard was published by BSI. It is the UK implementation of EN 3155-053:2007.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Panel ACE/6/-/3, Aerospace Co

5、nnectors.A list of organizations represented on this committee can be obtained on request to its secretary.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 3155-053April 2007ICS 49.060English VersionAerospace series - Electrical contacts used in elements ofconnection - Part 053: Contacts, electrica

6、l, female 053, type A,crimp, class S - Product standardSrie arospatiale - Contacts lectriques utiliss dans lesorganes de connexion - Partie 053 : Contacts lectriques,femelles 053, type A, sertir, classe S - Norme de produitLuft- und Raumfahrt - Elektrische Kontakte zur Verwendungin Verbindungselemen

7、ten - Teil 053: ElektrischeBuchsenkontakte 053, Typ A, crimpbar, Klasse S -ProduktnormThis European Standard was approved by CEN on 13 January 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of

8、a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version

9、 in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark,

10、 Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEURO

11、PISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3155-053:2007: E2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definition

12、s .4 4 Required characteristics.5 4.1 Dimensions and mass.5 4.2 Material, surface treatment.5 4.3 Permissible cables.6 4.4 Tooling6 4.5 Cable stripping.6 4.6 Tests6 4.7 Gauges for EN 2591-418 test 8 5 Designation 9 6 Marking .10 7 Technical specification .10 EN 3155-053:20073 Foreword This document

13、(EN 3155-053:2007) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Se

14、rvices of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2007, and conflicting national standards shall be withdrawn at th

15、e latest by October 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the natio

16、nal standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, P

17、oland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3155-053:20074 1 Scope This standard specifies the required characteristics and tests applicable to female electrical contacts 053, type A, crimp, class S, used in elements of connection according to

18、EN 3155-002. It shall be used together with EN 3155-001. The associated female contacts are defined in EN 3155-052. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated refe

19、rences, the latest edition of the referenced document (including any amendments) applies. EN 2083, Aerospace series Copper or copper alloy conductors for electrical cables Product standard. EN 2591*, Aerospace series Elements of electrical and optical connection Test methods. EN 3155-001, Aerospace

20、series Electrical contacts used in elements of connection Part 001: Technical specification. 1)EN 3155-002, Aerospace series Electrical contacts used in elements of connection Part 002: List and utilization of contacts. EN 3155-052, Aerospace series Electrical contacts used in elements of connection

21、 Part 052: Contacts, electrical, male 052, type A, crimp, class Product standard. EN 4008-016, Aerospace series Elements of electrical and optical connection Crimping tools and associated accessories Part 016: Crimping tool for electrical contacts according to EN 3155-052 and EN 3155-053 Product sta

22、ndard. 2)EUROCAE-ED-14E:2005, Environmental conditions and test procedures for airborne equipment. 3)3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 3155-001 apply. *All parts quoted in this standard. 1) Published as AECMA Prestandard at the date of p

23、ublication of this standard. 2) In preparation at the date of publication of this standard. 3) Published by: EUROCAE, 11 rue Hamelin 75783 PARIS CEDEX 16. EN 3155-053:20075 4 Required characteristics 4.1 Dimensions and mass See Figure 1. Mass: 90 g max. Dimensions and tolerances are expressed in mil

24、limetres and apply after plating. Key 1 Annealed area 2 1 hole 23,249,23 Manufacturer marking (trademark, logo, ) Figure 1 4.2 Material, surface treatment Material : copper alloy Surface treatment : gold on appropriate undercoat EN 3155-053:20076 4.3 Permissible cables See Table 1. Table 1 Size Size

25、 of conductor Contact Barrel Size Code Size Code AECMA Code aSection mm2AWG bRated test current A 4/0 4A 2/0 2A 680 68 2/0 260 aSee EN 2083. bAWG = American Wire Gage. 4.4 Tooling See Table 2. Table 2 Size Crimping tool Contact Barrel Basic tool Crimp die Locator 4/0 2/0 EN 4008-016 4.5 Cable stripp

26、ing See Table 3. Table 3 Size Stripped length of cable A mm Contact Barrel min. max. 4/0 2/0 22,86 27,94 4.6 Tests See Table 4. EN 3155-053:20077 Table 4 Applicable EN 2591- Test Not applicableAccording to EN 3155-001 Remarks 101 Visual examination X 102 Examination of dimensions and mass X 201 Cont

27、act resistance - low level X 202 Contact resistance at rated current X Measuring points on the cable, the two points 150 mm apart. Maximum voltage drop Initial: 60 mV After tests: 75 mV 204 Discontinuity of contacts in the microsecond range X 206 Measurement of insulation resistance X 207 Voltage pr

28、oof test X 208 Temperature rise due to rated current X 210 Electrical overload X 325 A for 5 min 435 A for 5 s 213 Shielding effectiveness from 100 MHz to 1 GHz X 301 Endurance at temperature X T = (200 2) C Duration: 1 000 h 305 Rapid change of temperature X TA= (200 2) C TB= ( 65 2) C 306 Mould gr

29、owth X 307 Salt mist X 315 Fluid resistance X 402 Shock X Method A Severity 300 403 Sinusoidal and random vibration X Part 1: Ambient temperature: 120 C Current: 200 A on three contacts 100 mA on one contact Curve R of EUROCAE-ED-14E 3 h per axis on three axis Curve W of EUROCAE-ED-14E on OX lengthw

30、ise axis contactDuration : 40 h continued EN 3155-053:20078 Table 4 (concluded) Applicable EN 2591- Test Not applicableAccording toEN 3155-001 Remarks 403 Sinusoidal and random vibration (concluded) X Part 2:Ambient temperature: 200 C Current: 260 A on three contacts 100 mA on one contact Curve R of

31、 EUROCAE-ED-14E 2 h per axis on OX and OY axis Part 3: Resonant frequencies determination Curve R of EUROCAE-ED-14E Vibration at resonance frequencies Ambient temperature: 200 C Current: 260 A on three contacts 100 mA on one contact 2 h per fixed resonant frequencies on OX axis 406 Mechanical endura

32、nce X 250 operations 415 Test probe damage (female contact) X 416 Contact bending strength X 417 Tensile strength (crimped connection) X 418 Gauge insertion/extraction forces (female contacts) X Maximum insertion force Initial: 135 N After test: 162 N Minimum extraction force Initial: 28 N After tes

33、t: 22 N 502 Restricted entry X 503 Contact deformation after crimping X 508 Measurement of thickness of coating on contacts X The measured thickness shall be recorded. 509 Adhesion of coating on contacts X 513 Magnetic permeability X 2 4.7 Gauges for EN 2591-418 test See Figure 2 and Table 5. EN 315

34、5-053:20079 Key 1 Ra0,15 m to 0,25 m 2 R Spherical edge Figure 2 Table 5 Contact size gauge A Max. 12,735 12,372 4/0 Min. 12,678 12,675 5 Designation EXAMPLE Description block CONTACT, ELECTRICAL Identity block EN3155-053F4A2A Number of this standard Type of contact F = female Contact size code (see

35、 Table 1) Barrel size code (see Table 1) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. EN 3155-053:200710 6 Marking See Figure 1. 7 Technical specification See EN 3155-001. EN 3155-053:2007blankBS EN BSI389 Chiswick High RoadLondonW4 4AL3155-

36、053:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revisio

37、n. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the S

38、ecretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of

39、standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders fo

40、r international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and i

41、ts Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to da

42、te with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Sta

43、ndards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Ex

44、cept as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in

45、 the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.