BS EN 3382-2012 Aerospace series Rings retaining internal axial mounting steel phosphated《航空航天系列 磷酸盐钢制轴向安装内置固定吊环》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 3382:2012Aerospace series Ringsretaining, internal, axialmounting, steel, phosphatedBS EN 3382:2012 BRITISH STANDARDNational forewordThis British Standard is the UK impleme

2、ntation of EN 3382:2012. The UK participation in its preparation was entrusted to TechnicalCommittee ACE/12, Aerospace fasteners and fastening systems. A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all t

3、he necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012ISBN 978 0 580 75711 2 ICS 49.030.50 Compliance with a British Standard cannot confer immunity from legal obligations.This British St

4、andard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 3382:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3382 March 2012 ICS 49.030.50 English Version Aerospace series -

5、 Rings retaining, internal, axial mounting, steel, phosphated Srie arospatiale - Anneaux darrt, montage axial, type intrieur, en acier, phosphats Luft- und Raumfahrt - Sicherungsringe, axial in Bohrungen montierbar, aus Stahl, phosphatiert This European Standard was approved by CEN on 24 September 2

6、011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained

7、 on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CE

8、NELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Mal

9、ta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights

10、 of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3382:2012: EBS EN 3382:2012EN 3382:2012 (E) 2 Contents Page Foreword 31 Scope and field of application 42 Normative references 43 Required characteristics .43.1 Configuration Dimensions Masses 43.2

11、 Materials .43.3 Surface treatment 44 Designation 85 Marking .86 Technical specification .87 Mounting .8BS EN 3382:2012EN 3382:2012 (E) 3 Foreword This document (EN 3382:2012) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquirie

12、s and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national st

13、andard, either by publication of an identical text or by endorsement, at the latest by September 2012, and conflicting national standards shall be withdrawn at the latest by September 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

14、rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croati

15、a, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 3382:2012EN 3382

16、:2012 (E) 4 1 Scope and field of application This standard defines the characteristics of axial mounting internal retaining rings, in steel, phosphated, for aerospace applications. The phosphating restricts the use at temperatures not exceeding 200 C. 2 Normative references The following documents,

17、in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Markin

18、g of aerospace products EN 3380, Aerospace series Rings retaining Technical specification EN 3425, Aerospace series Groove dimensions for axial mounting internal type retaining rings 3 Required characteristics 3.1 Configuration Dimensions Masses See figure 1 and table. 3.2 Materials Spring steel: 48

19、0530 HV (Diameter codes 008 to 038) 440510 HV (Diameter codes 040 to 165) 3.3 Surface treatment Phosphate to EN 2793, class A Before storing, the ring shall be protected by grease or oil. NOTE Detail of form not stated are left to the manufacturers option. BS EN 3382:2012EN 3382:2012 (E) 5 Figure 1

20、Key: a Free b Apply prior to phosphating c Table d At mounting e Installed f Diameter codes 008 to 048 g Diameter codes 025 to 165 BS EN 3382:2012EN 3382:2012 (E) 6 Table 1 Dimensions in millimetres Diameter code bA B cD1D2D3D4P S R Mass dmax. nom. Tol. max. max. min. h11 max. kg/1 000 pieces 008 2,

21、4 1,1 8,7 +0,36 0,16 2,8 3,6 1 0,1 0,8 0,08 0,100 009 2,5 1,3 9,8 3,1 4,4 0,130 010 3,2 1,4 10,8 3,6 4 1,2 1 0,1 0,260 011 3,3 1,5 11,8 3,9 4,8 0,310 012 3,4 1,7 13 4,7 5,7 1,5 0,370 013 3,6 1,8 14,1 5,3 6,4 0,420 014 3,7 1,9 15,1 6 7,2 1,7 0,520 015 3,7 2 16,2 7 8,3 0,560 016 3,8 2 17,3 7,7 9,2 0,6

22、00 017 3,9 2,1 18,3 +0,42 0,21 8,4 10 0,650 018 4,1 2,2 19,5 8,9 10,8 2 0,740 019 4,1 2,2 20,5 9,8 11,8 0,830 020 4,2 2,3 21,5 10,6 12,6 0,900 021 4,2 2,4 22,5 11,6 13,6 1,000 022 4,2 2,5 23,5 12,6 14,6 1,100 023 4,2 2,5 24,6 13,6 15,7 0,15 1,2 0,12 1,340 024 4,4 2,6 25,9 14,2 16,4 1,420 025 4,5 2,7

23、 26,9 15 17,2 1,500 026 4,7 2,8 27,9 15,6 17,8 1,600 028 4,8 2,9 30,1 +0,5 0,25 17,4 19,8 1,800 030 4,8 3 32,1 19,4 21,8 2,060 031 5,2 3,1 33,4 19,6 22,3 2,5 2,130 032 5,4 3,2 34,4 20,2 22,9 2,210 034 5,4 3,3 36,5 22,2 24,9 1,5 0,15 3,200 035 5,4 3,4 37,8 23,2 26,2 3,540 036 5,4 3,5 38,8 24,2 27,2 3

24、,700 037 5,5 3,6 39,8 25 28 3,740 038 5,5 3,7 40,8 26 29 3,900 040 5,8 3,9 43,5 +0,78 0,39 27,4 30,9 0,2 1,75 0,17 4,700 042 5,9 4,1 45,5 29,2 32,7 5,400 045 6,2 4,3 48,5 31,6 35,1 6,000 047 6,4 4,4 50,5 +0,92 0,46 33,2 36,7 6,100 048 6,4 4,5 51,5 34,6 37,7 6,700 050 6,5 4,6 54,2 36 40 2 0,2 7,300 0

25、52 6,7 4,7 56,2 37,6 41,6 8,200 055 6,8 5 59,2 40,4 44,4 8,300 056 6,8 5,1 60,2 41,4 45,4 8,800 058 6,9 5,2 62,2 43,2 47,2 10,500 060 7,3 5,4 64,2 44,4 48,4 11,100 062 7,3 5,5 66,2 46,4 50,4 11,200 063 7,3 5,6 67,2 47,4 51,4 12,400 065 7,6 5,8 69,2 48,8 52,8 3 2,5 0,25 14,300 068 7,8 6,1 72,5 51,4 5

26、5,4 16,000 070 7,8 6,2 74,5 53,4 57,4 16,500 072 7,8 6,4 76,5 55,4 59,4 18,100 075 7,8 6,6 79,5 58,4 62,4 18,800 077 7,9 6,7 81,5 60 64,2 19,000 aSee page 7. bSee page 7. cSee page 7. dSee page 7. BS EN 3382:2012EN 3382:2012 (E) 7 Table 1 (concluded) Dimensions in millimetres Diameter code bA B cD1D

27、2D3D4P S R Mass dmax. nom. Tol. max. max. min. h11 max. kg/1 000 pieces 078 8,5 6,8 82,5 +1,080,54 60,2 64 3 0,20 2,5 0,25 20,400 080 8,5 7 85,5 62 66,5 22,000 081 8,5 7 86,5 63 67,5 23,000 082 8,5 7 87,5 64 68,5 24,000 083 8,5 7 88,5 65 69,5 0,25 25,000 085 8,6 7,2 90,5 66,8 71,3 3,5 3 0,3 26,300 0

28、87 8,6 7,3 92,5 68,8 73,3 29,000 088 8,6 7,4 93,5 69,8 74,3 31,000 090 8,6 7,6 95,5 71,8 76,3 33,000 092 8,7 7,8 97,5 73,6 78,1 35,000 095 8,8 8,1 100,5 76,4 80,9 37,000 097 8,8 8,2 102,5 78,4 82,9 39,000 098 9 8,3 103,5 79 83,5 41,000 100 9 8,4 105,5 81 85,5 42,000 102 9,2 8,5 108 82,6 87,6 4 0,4 5

29、5,000 105 9,2 8,7 112 85,6 90,6 56,000 107 9,5 8,8 114 87 92 58,500 108 9,5 8,9 115 88 93 60,000 110 10,4 9 117 88,2 93,2 64,500 112 10,5 9,1 119 90 95 72,000 115 10,5 9,3 122 +1,260,63 93 98 74,500 117 10,6 9,5 124 94,8 99,8 75,000 118 10,7 9,6 125 95 100,6 75,500 120 11 9,7 127 97 102 77,000 122 1

30、1 9,8 129 99 104 4 78,000 125 11 10 132 102 107 79,000 127 11 10,1 134 104 109 80,500 128 11 10,2 135 105 110 81,000 130 11 10,2 137 107 112 82,000 132 11 10,3 139 109 114 83,000 135 11,2 10,5 142 112 116,6 84,000 137 11,2 10,5 144 114 118,6 85,500 138 11,2 10,6 145 115 119,6 86,000 140 11,2 10,7 14

31、7 117 121,6 87,500 142 11,3 10,8 149 119 123,4 89,000 145 11,4 10,9 152 122 126,2 93,000 147 11,6 11 154 123 127,8 96,000 148 11,8 11,1 155 124 128,4 100,000 150 12 11,2 158 125 131 105,000 152 12 11,3 161 127 133 106,000 155 12 11,4 164 130 136 107,000 157 12 11,5 166 132 138 108,000 158 12,3 11,5

32、167 132,4 138,4 109,000 160 13 11,6 169 133 139 110,000 162 13 11,7 171,5 135 141 118,000 165 13 11,8 174,5 138 144 125,000 aValues apply after phosphating. bCorresponds to the nominal diameter (expressed in millimetres) of the bore in which the ring shall be mounted (see EN 3425). cShall not exceed

33、 A” max. dApproximate values, calculated on the basis of 7,85 kg/dm3, given for information purpose only. BS EN 3382:2012EN 3382:2012 (E) 8 4 Designation EXAMPLE Description blockRETAINING RING, INTERNAL, AXIAL MOUNTING Identity block EN 3382 016 Number of EN Standard Diameter code (See table) NOTE

34、If necessary, the originator code I 9005 may be introduced between the description block and the identity block. 5 Marking EN 2424, style G. 6 Technical specification EN 3380 7 Mounting EN 3425 This page deliberately left blankBSI is the independent national body responsible for preparing British St

35、andards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standar

36、ds Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or ed

37、itions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the insid

38、e frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.T

39、el: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Servi

40、ces.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on na

41、tional, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other

42、 benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the d

43、ata, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI

44、 for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.

45、 This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: