BS EN 3475-203-2006 Aerospace series - Cables electrical aircraft use - Test methods - Dimensions《航空航天系列 飞行器用电气电缆 试验方法 尺寸规格》.pdf

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58methods Part 203: DimensionsThe European Standard EN 3475-203:2006 has the status of a British Stan

2、dardICS 49.060Aerospace series Cables, electrical, aircraft use Test BRITISH STANDARDBS EN 3475-203:2006Incorporating Corrigendum No. 1BS EN 3475-203:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 September 2006 BSI 2006ISBN 0 580 491

3、67 6Amendments issued since publicationAmd. No. Date Comments16691 Corrigendum 1September 2006 Correction to the National ForewordThis publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. National forewordThis British

4、Standard is the official English language version of EN 3475-203:2006.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Subcommittee ACE/6/-/2, Aerospace - Cables.A list of organizations represented on ACE/

5、6/-/2 can be obtained on request to its secretary.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 3475-203April 2006ICS 49.060English VersionAerospace series - Cables, electrical, aircraft use - Testmethods - Part 203: DimensionsSrie arospatiale - Cbles lectriques usagearonautique - Mthodes dessai

6、s - Partie 203 :DimensionsLuft- und Raumfahrt - Elektrische Leitungen frLuftfahrtverwendung - Prfverfahren - Teil 203: MaeThis European Standard was approved by CEN on 27 February 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving

7、 this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (

8、English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, C

9、zech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROP

10、EN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3475-203:2006: EEN 3475-203:2006 (E) 2 Contents Page Foreword 3 1 Scope .4 2

11、 Normative references .4 3 Apparatus 4 4 Method .4 5 Requirements 5 EN 3475-203:2006 (E) 3 Foreword This European Standard (EN 3475-203:2006) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance w

12、ith the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an i

13、dentical text or by endorsement, at the latest by October 2006, and conflicting national standards shall be withdrawn at the latest by October 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be h

14、eld responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France

15、, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3475-203:2006 (E) 4 1 Scope This standard specifies a method of measuring the dimension

16、s of conductors and cables. It shall be used together with EN 3475-100. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced

17、 document (including any amendments) applies. EN 3475-100, Aerospace series Cables, electrical, aircraft use Test methods Part 100: General. 3 Apparatus 3.1 Conductor diameter The measurement shall be made with a friction or dial micrometer with flat ends having a diameter of at least 5 mm. Use an i

18、nstrument constructed with a vernier capable of measurement to the nearest 0,01 mm. 3.2 Insulation and/or jacket The measurements shall be carried out either with a profile projector, or measuring microscope or equivalent apparatus. 3.3 External diameter The measurement shall be made with a friction

19、 or dial micrometer with flat ends having a diameter of at least 5 mm for single cables and at least 15 mm for multiconductor cables, or with a profile projector. 4 Method 4.1 Conductor The following shall be verified: the number of strands making up the conductor; the nominal diameter of the strand

20、s; the diameter of the suitably straightened conductor. Measure the outside diameter (OD) of the specimen in at least three locations approximately one meter apart. Each measurement shall consist of two micrometer readings taken at 90 from each other. (OD) = average diameter over the conductor EN 34

21、75-203:2006 (E) 5 4.2 Insulation and/or jacket 4.2.1 Wrapped insulation and/or jacket Verify the following: the number of tapes (if possible); the sealing of the tapes; the tape overlap; the minimum thickness of the outer coating or layer or sealed material (if applicable). 4.2.2 Extruded insulation

22、 and/or jacket The radial thickness shall be measured at the thinnest and thickest points. 4.2.3 Minimum average thickness Four measurements shall be made successively around the circumference of the specimen at 90 intervals. The first measurement shall be made at the thinnest point of the cross-sec

23、tion. 4.3 External diameter 4.3.1 Single insulated wire or cable Measure the outside diameter (OD) of the specimen in at least three locations approximately one metre apart. Each measurement shall consist of two micrometer readings taken at 90 from each other. 4.3.2 Non cylindrical cables Measure th

24、e outside diameter (OD) of the specimen in at least six locations approximately equidistant along the length of the specimen. NOTE The location of each measurement shall be made at the maximal overall dimension. (OD) = average diameter over the insulation or jacket 5 Requirements 5.1 Conductor The n

25、umber of strands, the diameter of the strands and of the conductor shall comply with the values given in the product standard (if applicable). EN 3475-203:2006 (E) 6 5.2 Insulation and/or jacket 5.2.1 Wrapped insulation and/or jacket The characteristics shall conform to requirements given in the tec

26、hnical specification or the product standard (if applicable). 5.2.2 Extruded insulation and/or jackets The characteristics shall conform to requirements given in the technical specification or the product standard (if applicable). The minimum value of the radial thickness shall not be less than 70 %

27、 of the maximum measured value (the minimum to maximum thickness ratio). 5.2.3 Minimum thickness average The average of the four measurements shall be equal to or greater than the minimum value given in the product standard (if applicable). 5.3 External diameter The external diameter (average) shall

28、 conform to that stated in the product standard. blankBS EN BSI389 Chiswick High RoadLondonW4 4AL3475-203:2006BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international lev

29、el. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grat

30、eful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual upd

31、ating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: or

32、dersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a

33、 wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (

34、0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 70

35、02. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI al

36、so holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, re

37、cording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.