BS EN 3545-007-2014 Aerospace series Connectors electrical rectangular with sealed and non-sealed rear plastic housing locking device operating temperatures - 55 C to 175 C Cable c.pdf

1、BSI Standards PublicationBS EN 3545-007:2014Aerospace series Connectors, electrical,rectangular, with sealedand non-sealed rear, plastichousing, locking device,operating temperatures 55C to 175 CPart 007: Cable clamp Product standardBS EN 3545-007:2014 BRITISH STANDARDNational forewordThis British S

2、tandard is the UK implementation of EN 3545-007:2014.It supersedes BS EN 3545-007:2005 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic electrical and fibre optictechnology.A list of organizations represented on this committee ca

3、n beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 87668 4ICS 49.060Compliance

4、with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2014.Amendments issued since publicationDate Text affectedBS EN 3545-007:2014EUROPEAN STANDARD NORME EUROPENNE EUR

5、OPISCHE NORM EN 3545-007 December 2014 ICS 49.060 Supersedes EN 3545-007:2005English Version Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures - 55 C to 175 C - Part 007: Cable clamp - Product standard Sri

6、e arospatiale - Connecteurs lectriques, rectangulaires, tanches et non tanches larrire, botier en plastique, verrouillage, tempratures dutilisation -55 C 175 C - Partie 007: Serre-cble - Norme de produit Luft- und Raumfrahrt - Elektrische Rechtecksteckverbinder mit und ohne hintere Abdichtung, Plast

7、ikgehuse, Verriegelungssystem, Betriebstemperaturen von - 55 C to 175 C - Teil 007: Zugentlastungsklemme - Produktnorm This European Standard was approved by CEN on 22 November 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving t

8、his European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official

9、 versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Aus

10、tria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swed

11、en, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CE

12、N national Members. Ref. No. EN 3545-007:2014 EBS EN 3545-007:2014EN 3545-007:2014 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Required characteristics .4 4.1 Dimensions, mass .4 4.2 Material .8 4.3 Main general characteristics 8 5 Designation 9 6 M

13、arking .9 7 Technical specification .9 Figures Figure 1 Dimensions of model Code D .5 Figure 2 Dimensions of model Code E .6 Figure 3 Dimensions of model Code G .7 Figure 4 Dimensions of model Code H .8 BS EN 3545-007:2014EN 3545-007:2014 (E) 3 Foreword This document (EN 3545-007:2014) has been prep

14、ared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countr

15、ies of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2015, and conflicting national standards shall be withdrawn at the latest by June 2015. Attention

16、 is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 3545-007:2005. According to the CEN-CENELEC Internal Regulations, t

17、he national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latv

18、ia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 3545-007:2014EN 3545-007:2014 (E) 4 1 Scope This European Standard specifies cable clamp in the family of rectangular electrical conn

19、ectors with sealed and non-sealed rear, plastic housing, locking device, for operating temperatures from 55 C to 175 C. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, on

20、ly the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100, Aerospace series Elements of electrical and optical connection Test methods Part 100: General EN 3545-001, Aerospace series Conne ctors, electrical, re

21、ctangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175 C Part 001: Technical specification EN 3545-002, Aerospace series Connectors, electrical, rectangular, with sealed a nd non-sealed rear, plastic housing, locking device, operating temperat

22、ures 55 C to 175 C Part 002: Specification of performance and contact arrangements 3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 2591-100 apply. 4 Required characteristics 4.1 Dimensions, mass The dimensions of attachment system are given in Figure

23、1, Figure 2, Figure 3 or Figure 4. Dimensions and tolerances are in millimetres. Mass: 06 g max. for model Code D 09 g max. for model Code E 12 g max. for model Code G 16,5 g max. for model Code H BS EN 3545-007:2014EN 3545-007:2014 (E) 5 Model Code D General tolerance: 0,2 Figure 1 Dimensions of mo

24、del Code D BS EN 3545-007:2014EN 3545-007:2014 (E) 6 Model Code E General tolerance: 0,2 Figure 2 Dimensions of model Code E BS EN 3545-007:2014EN 3545-007:2014 (E) 7 Model code G General tolerance: 0,2 NOTE This backshell can be used only with cable gauge 26 to 12. Figure 3 Dimensions of model Code

25、 G BS EN 3545-007:2014EN 3545-007:2014 (E) 8 Model code H General tolerance: 0,2 Figure 4 Dimensions of model Code H 4.2 Material Material: thermoplastic resin 4.3 Main general characteristics See EN 3545-002. BS EN 3545-007:2014EN 3545-007:2014 (E) 9 5 Designation EXAMPLE Description block CABLE CL

26、AMP Identity block EN3545-007SCD Number of this standard Cable clamp: SC Model code NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 6 Marking Unless there are other specific contractual requirements, the marking shall include: the identity bloc

27、k as defined in Clause 5; the manufacturers name or trademark. 7 Technical specification See EN 3545-001. This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and s

28、ervices.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumer

29、s, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors c

30、hoose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou c

31、an buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can b

32、e ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted Euro

33、pean and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becomin

34、g a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit

35、a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur Bri

36、tish Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Copyright

37、All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such info

38、rmation to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permis

39、sion from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW