BS EN 3646-003-2006 Aerospace series - Connectors electrical circular bayonet coupling operating temperature 175 ℃ or 200 ℃ continuous - Part 003 Receptacle square flange mounting .pdf

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58coupling, operating temperature 175 C or 200 C continuous Part 003: Receptacle, square flange mount

2、ing Product standardThe European Standard EN 3646-003:2006 has the status of a British StandardICS 49.060Aerospace series Connectors, electrical, circular, bayonet BRITISH STANDARDBS EN 3646-003:2006BS EN 3646-003:2006This British Standard was published under the authority of the Standards Policy an

3、d Strategy Committee on 29 September 2006 BSI 2006ISBN 0 580 49194 3Amendments issued since publicationAmd. No. Date CommentsThis publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard c

4、annot confer immunity from legal obligations.National forewordThis British Standard was published by BSI. It is the UK implementation of EN 3646-003:2006. The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to S

5、ubcommittee ACE/6/-/3, Aerospace Connectors.A list of organizations represented on ACE/6/-/3 can be obtained on request to its secretary.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3646-003 May 2006 ICS 49.060 English Version Aerospace series - Connectors, electrical, circular, bayonet coup

6、ling, operating temperature 175 C or 200 C continuous - Part 003: Receptacle, square flange mounting - Product standard Srie arospatiale - Connecteurs lectriques circulaires accouplement par baonnettes, temprature dutilisation 175 C ou 200 C continu - Partie 003 : Embase fixation par collerette carr

7、e - Norme de produit Luft- und Raumfahrt - Elektrische Rundsteckverbinder mit Bajonettkupplung, Betriebstemperatur 175 C oder 200 C konstant - Teil 003: Fester Steckverbinder mit quadratischem Montageflansch - Produktnorm This European Standard was approved by CEN on 3 February 2006. CEN members are

8、 bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to t

9、he Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same sta

10、tus as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovaki

11、a, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reserved worldwide

12、for CEN national Members. Ref. No. EN 3646-003:2006: EEN 3646-003:2006 (E) 2 Contents Page Foreword 3 1 Scope .4 2 Normative references .4 3 Terms and definitions.4 4 Required characteristics 4 5 Designation .7 6 Marking 8 7 Technical specification.8 EN 3646-003:2006 (E) 3 Foreword This European Sta

13、ndard (EN 3646-003:2006) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Offic

14、ial Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2006, and conflicting national standards shall be withdraw

15、n at the latest by November 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, t

16、he national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Pol

17、and, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3646-003:2006 (E) 4 1 Scope This standard defines the characteristics of square flange receptacles of the family of bayonet coupling circular connectors, intended for use in an operating temperature ran

18、ge of 65 C to 175 C or 200 C continuous. It applies to models defined in Table 3. For contact, filler plugs and rear accessories associated with this receptacle see EN 3646-002. For plugs and protective covers see EN 3646-008 and EN 3646-009 respectively. 2 Normative references The following referen

19、ced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3155-002, Aerospace series Electrical contacts used in elements of

20、connection Part 002: List and utilization of contacts. EN 3646-001, Aerospace series Connectors, electrical, circular, bayonet coupling, operating temperature 175 C or 200 C continuous Part 001: Technical specification.1)EN 3646-002, Aerospace series Connectors, electrical, circular, bayonet couplin

21、g, operating temperature 175 C or 200 C continuous Part 002: Specification of performance and contact arrangements. EN 3646-008, Aerospace series Connectors, electrical, circular, bayonet coupling, operating temperature 175 C or 200 C continuous Part 008: Plug Product standard. EN 3646-009, Aerospac

22、e series Connectors, electrical, circular, bayonet coupling, operating temperature 175 C or 200 C continuous Part 009: Protective cover for receptacle Product standard. 3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 3646-001 apply. 4 Required charact

23、eristics 4.1 Dimensions and mass See Figure 1 and Table 1. Dimensions and tolerances are in millimetres, they apply after surface treatment. Interface mating and rear dimensions see EN 3646-001. 1) Published as AECMA Prestandard at the date of publication of this standard. EN 3646-003:2006 (E) 5 Key

24、 1 2,21 shells 08 to 18 3 Panel 5,38 shells 20 to 24 4 Polarizing strip optional colour 2 According to variant 5 Four holes diameter M aMaximum thickness of the support and the fixing screw heads for fitting the connector from the rear of the panel bSee EN 3646-001, Figures 1 and 3, for references A

25、 and B. Figure 1 Table 1 M N S T X Y Mass agHousing size 0,15 + 0,79 0 max. max. max. 08 15,10 21,03 6 10 8,26 24,2 10 12 20,62 26,59 13 14 3,01 28,98 16 16 24,6 31,34 22 18 10,95 26,97 33,73 1,45 0,86 25,50 26 20 29,36 36,91 33 22 3,15 14,12 31,75 40,10 39 24 3,73 14,96 34,92 43,27 2,25 1,09 27,30

26、49 aMass without accessory and without contacts.EN 3646-003:2006 (E) 6 4.2 Panel cut-out Recommended panel cut-out dimensions: see Figure 2 and Table 2. Dimensions and tolerances are in millimetres. Key 1 Four holes diameter C Figure 2 Table 2 A B C D Housing size + 0,25 0 0,15 min. 08 14,40 15,10 3

27、2 10 17,59 18,26 35 12 22,60 20,62 38 14 25,52 23,01 41 16 28,70 24,61 45 18 31,87 26,97 47 20 35,05 29,36 51 22 38,22 31,75 3,15 53 24 41,40 34,92 3,73 57 4.3 Material and surface treatment See Table 3. EN 3646-003:2006 (E) 7 4.4 Main general characteristics See EN 3646-002. 4.5 Possible combinatio

28、ns of plugs and receptacles See EN 3646-002. 4.6 Electrical, mechanical and climatic characteristics See EN 3646-002. 5 Designation EXAMPLE Description block CONNECTOR, ELECTRICAL, RECEPTACLE Identity block EN3646A01006MN Number of the basic standard Model (see Table 3) Square flange mounted recepta

29、cle (see EN 3646-002) Housing size and contacts arrangement (see EN 3646-002) Type of contact (see Table 4) Male: M Female: F Polarization (see EN 3646-002) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. Table 3 Connector models Model Descript

30、ion A Sealed receptacles with housing (shell) in black anodized aluminium alloy with contacts With three teeth at the rear of the connector Maximum operating temperature 200 C continuous RS Sealed receptacle with housing (shell) in nickel-plated aluminium alloy Crimped contacts With three teeth at t

31、he rear of the connector Maximum operating temperature 200 C continuous WS Sealed receptacles with housing (shell) in olive green cadmium alloy Resistance to salt spray 500 h Crimped contacts With teeth over the entire periphery at the rear of the connector Maximum operating temperature 175 C contin

32、uous EN 3646-003:2006 (E) 8 Table 4 Types of contacts and delivery Contacts Delivered without contacts Delivered with contact standard barrels a EN3155-xxx2020 EN3155-xxx1616 EN3155-xxx1212 Delivered with specific contact size 20 with special barrel aEN3155-xxx2018 b Male A M C Female B F D aSee EN

33、3155-002. bOnly affects size 20 contact arrangements 6 Marking Unless there are other specific contractual requirements, the marking shall include. 6.1 Marking on the product the manufacturers part number corresponding to the identity block as defined in Clause 5, except for the 13thor 14thcharacter

34、 which shall correspond to Table 5; the date of manufacture (year, week); the manufacturers name or trade mark. Table 5 13thor 14thcharacter of the identity block for A, M, C a M for B, F, D aF aSee Table 4. 6.2 Marking on the individual packaging the EN reference corresponding to the purchasing ord

35、er; the manufacturers part number corresponding to the above EN reference; the date of manufacture (year, week); the manufacturers name of trade mark. 7 Technical specification See EN 3646-001. blankBS EN BSI389 Chiswick High RoadLondonW4 4AL3646-003:2006BSI British Standards InstitutionBSI is the i

36、ndependent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that t

37、hey possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the

38、identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, interna

39、tional and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply

40、 the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI e

41、lectronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantia

42、l discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at h

43、ttp:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Pa

44、tents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessar

45、y details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.