BS EN 3682-003-2012 Aerospace series Connectors plug and receptacle electrical rectangular interchangeable insert type rack to panel operating temperature 150C continuous Inserts P.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 3682-003:2012Aerospace series Connectors, plug and r e c e p t a c l e , e l e c t r i c a l , r e c t a n g u l a r , i n t e r c h a n g e a b l e insert type, rack to pa

2、nel, operating temperature 150 C continuousPart 003: Inserts Product standardBS EN 3682-003:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 3682-003:2012. It supersedes BS EN 3682-003:2006, which is withdrawn.The UK participation in its preparation was entr

3、usted to Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible

4、 for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012.ISBN 978 0 580 77227 6 ICS 49.060 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Po

5、licy and Strategy Committee on 30 November 2012.Amendments issued since publicationDate Text affectedBS EN 3682-003:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3682-003 October 2012 ICS 49.060 Supersedes EN 3682-003:2006English Version Aerospace series - Connectors, plug and receptacle,

6、 electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 C continuous - Part 003: Inserts - Product standard Srie arospatiale - Connecteurs lectriques rectangulaires rackables, fiches et embases, inserts interchangeables, temprature dutilisation 150 C continu -

7、 Partie 003 : Inserts - Norme de produit Luft- und Raumfahrt - Elektrischer Rechtecksteckverbinder, freie und feste Bauform, auswechselbare Isolierkrper, Gestell-Einschubsteckverbinder, Betriebstemperatur 150 C konstant - Teil 003: Einstze - Produktnorm This European Standard was approved by CEN on

8、25 February 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards ma

9、y be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified

10、to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland

11、, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: A

12、venue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3682-003:2012: EBS EN 3682-003:2012EN 3682-003:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Re

13、quired characteristics .45 Designation 96 Marking 107 Technical specification 10BS EN 3682-003:2012EN 3682-003:2012 (E) 3 Foreword This document (EN 3682-003:2012) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes

14、carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, eith

15、er by publication of an identical text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the latest by April 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or C

16、ENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 3682-003:2006. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Be

17、lgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Swit

18、zerland, Turkey and the United Kingdom. BS EN 3682-003:2012EN 3682-003:2012 (E) 4 1 Scope This European Standard defines the inserts used in EN 3682 connectors. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for

19、its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3682 (all parts), Aerospace series Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type

20、, rack to panel, operating temperature 150 C continuous 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 3682-001 apply. 4 Required characteristics 4.1 Insert interface dimensions for insert with size 22 contact cavities arrangements See Figures 1, 2 a

21、nd Tables 1, 2 and 3. BS EN 3682-003:2012EN 3682-003:2012 (E) 5 Dimensions in millimetres Insert for plug shell aircraft side Insert for receptacle shell equipment side Key 1 manufacturer name and part number on this side or opposite 2 interfacial seal 3 grommet aInterfacial seal applies to socket i

22、nsert only. bSize 22. cExcept size 22. Figure 1 BS EN 3682-003:2012EN 3682-003:2012 (E) 6 Table 1 Housing Cavity A B C D E F G cord inside Plug A, C, E 13,13 13,03 12,19 11,56 22,1021,59 39,04 39,002 38,8938,66 40,1839,95 1,50 35,00 Receptacle A, C, E 3,55 3,45 2,67 2,03 Plug B, D, F 13,13 13,03 12,

23、19 11,56 9,40 8,89 27,86427,826 27,7127,48 29,0128,78 1,50 27,81 Receptacle B, D, F 3,55 3,45 2,67 2,03 Table 2 Insert M T R 118Q2 equipment side 9,30 max. 5,90 max. 1,57 max. aircraft side 9,60 min. 6,55 min. 1,57 min. 68Q2 equipment side 3,20 max. 6,00 max. 1,57 max. aircraft side 3,55 min. 6,40 m

24、in. 1,57 min. Figure 2 BS EN 3682-003:2012EN 3682-003:2012 (E) 7 Table 3 Insert H J K R1R268Q4 equipment side 8,00 max. 18,30 max. 4,80 min. 1,00 min. 1,00 max. aircraft side 9,00 min. 19,30 min. 3,80 max. 1,00 max. 1,00 max. 4.2 Insert interface dimensions for insert without size 22 contact cavitie

25、s arrangements See Figure 3 and Table 4. Dimensions in millimetres Key 1 manufacturer name and part number on this side or opposite 2 interfacial seal 3 grommet aInterfacial seal applies to pin insert only.Figure 3 BS EN 3682-003:2012EN 3682-003:2012 (E) 8 Table 4 Housing Cavity A B C D E F G cord i

26、nside Plug A, C, E 15,59 15,49 12,19 11,56 22,1021,59 39,04 39,002 38,8938,66 40,1839,95 1,50 35,00 Receptacle A, C, E 1,09 0,99 1,14 0,94 Plug B, D, F 15,59 15,49 12,19 11,56 9,40 8,89 27,86 27,76 27,7127,48 29,0128,78 1,50 27,81 Receptacle B, D, F 1,09 0,99 1,14 0,94 4.3 Dimensions of metallic ins

27、erts See Figure 4 and Table 5. Dimensions in millimetres Key 1 manufacturer name and part number on this side or opposite 2 interfacial seal 3 grommet aInterfacial seal applies to pin insert only. bGeometry optional.Figure 4 BS EN 3682-003:2012EN 3682-003:2012 (E) 9 Table 5 Housing Cavity A B C D co

28、rd inside Plug A, C, E 15,59 15,49 38,89 38,86 40,18 39,95 1,50 35,00 Receptacle A, C, E 1,09 0,99 Plug B, D, F 15,59 15,49 27,81 27,68 29,01 28,78 1,50 35,00 Receptacle B, D, F 1,09 0,99 5 Designation EXAMPLE Description block ELECTRICAL CONNECTOR, INSERT Identity block EN 3682 1 P 70 C1 G L Standa

29、rd reference Type of insert (see Table 6) Housing Type (R = Receptacle, P = Plug) Number of signal and power contacts Number of: contacts: Coaxial: Cx (x = quantity) Triaxial: Tx (x = quantity) Quadrax: Qx (x = quantity) Connection to the ground G: coaxial, triaxial and quadrax contacts connected to

30、 the ground A: coaxial, triaxial and quadrax contacts not connected to the ground Contact delivery: if left blank: insert delivered with contacts except coaxial, triaxial and quadrax contacts; L: insert delivered without contacts. Table 6 Type of insert Description 1 For cavities A, C, E 2 For cavit

31、ies B, D, F BS EN 3682-003:2012EN 3682-003:2012 (E) 10 6 Marking Insert identification marking, as specified in Clause 5, should be applied in the position shown on the corresponding drawing. In addition, marking shall show: date of manufacture (year week); manufacturer name or trademark. 7 Technica

32、l specification See EN 3682-001. This page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is

33、 incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are period

34、ically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while

35、 using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an indiv

36、idual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the B

37、SI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementatio

38、n of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept

39、 up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards a

40、nd PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity

41、that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval sy

42、stem or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: