BS EN 3716-002-2006 Aerospace series - Connectors single-way with triaxial interface for transmission of digital data - Part 002 Conditions of use and list of product standards《航空航.pdf

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58for transmission of digital data Part 002: Conditions of use and list of product standardsThe Europ

2、ean Standard EN 3716-002:2006 has the status of a British StandardICS 49.060Aerospace series Connectors, single-way with triaxial interface, BRITISH STANDARDBS EN 3716-002:2006BS EN 3716-002:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on

3、 29 September 2006 BSI 2006ISBN 0 580 49243 5Amendments issued since publicationAmd. No. Date CommentsThis publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity f

4、rom legal obligations. National forewordThis British Standard was published by BSI. It is the UK implementation of EN 3716-002:2006.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Subcommittee ACE/6/-/3,

5、Aerospace Connectors.A list of organizations represented on ACE/6/-/3 can be obtained on request to its secretary.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 3716-002May 2006ICS 49.060English VersionAerospace series - Connectors, single-way with triaxial interface,for transmission of digital d

6、ata - Part 002: Conditions of use andlist of product standardsSrie arospatiale - Connecteur, monovoie, avec interfacetriaxiale, pour transmission de donnes numriques - Partie002 : Conditions dutilisation et liste des normes de produitsLuft- und Raumfahrt - Steckverbinder, triaxial fr digitaleDatenbe

7、rtragung in einer Richtung - Teil 002:Verwendungsbedingungen und Liste der ProduktnormenThis European Standard was approved by CEN on 20 February 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status

8、of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A versio

9、n in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, F

10、inland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOM

11、ITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3716-002:2006: E2 Contents Page Foreword 3 1 Scope .4 2 Normative references .4 3 Terms and definitions.4 4 Co

12、nditions of use4 5 Product standards 5 6 Keying5 7 Contacts.5 8 Rear accessories.5 9 Tooling.5 EN 3716-002:20063 Foreword This European Standard (EN 3716-002:2006) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carri

13、ed out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either

14、by publication of an identical text or by endorsement, at the latest by November 2006, and conflicting national standards shall be withdrawn at the latest by November 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/o

15、r CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark,

16、Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3716-002:20064 1 Scope This standard specifies the conditions o

17、f use common to single-way connectors with triaxial interface for transmission of digital data according to EN 3716-001 and gives the list of product standards. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, onl

18、y the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3375-003, Aerospace series Cables, electrical, for signal data transmissions Part 003: Cable, bifilar, double-braid Product standard. 1)EN 3375-004, Aerospace ser

19、ies Cables, electrical, for signal data transmissions Part 004: Cable, bifilar, single-braid Product standard. 1)EN 3375-005, Aerospace series Cables, electrical, for signal data transmissions Part 005: Cable, bifilar, double-braid, high immunity Product standard. 1)EN 3716-001*, Aerospace series Co

20、nnector, single-way, with triaxial interface for transmission of digital data Part 001: Technical specification. MIL-STD-1553B, Digital time division command/Response multiplex data bus. 2)3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 3716-001 apply

21、. 4 Conditions of use 4.1 Cable permitted EN 3375-003 EN 3375-004 EN 3375-005 4.2 Service characteristics 4.2.1 Electrical conditions Those for digital transmissions, particularly those corresponding to standard MIL-STD-1553B Insulation resistance at ambient temperature: 5 000 M Voltage strength at

22、sea level: 900 V r.m.s. Voltage strength at altitude: 200 V r.m.s. at 4,7 kPa * And all parts quoted. 1) In preparation at the date of publication of this standard. 2) Published by: Department of Defense (DOD), The Pentagon, Washington D.C. 20301, USA. EN 3716-002:20065 4.2.2 Climatic conditions Ser

23、vice temperature: Tmin. : 65 C Tmax. : 150 C Salt spray: 500 h Fluid resistance: see EN 3716-001 4.2.3 Mechanical conditions Mechanical endurance: 500 operations 5 Product standards Solder receptacle (with or without braid connection) EN 3716-003 Solder plug (with or without braid connection) EN 371

24、6-004 Crimp receptacle EN 3716-005 Crimp plug EN 3716-006 Crimp receptacle (without braid connection) EN 3716-007 Flight cap for plug EN 3716-008 Flight cap for receptacle EN 3716-009 6 Keying Not applicable 7 Contacts The central contact is not removable after assembly. 8 Rear accessories Not appli

25、cable 9 Tooling Not applicable. See Clause 7 above. EN 3716-002:2006BS EN BSI389 Chiswick High RoadLondonW4 4AL3716-002:2006BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the int

26、ernational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We

27、 would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an

28、individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7

29、001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standards

30、BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Cent

31、re. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44

32、 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI public

33、ations. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, ph

34、otocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.