BS EN 3733-005-2007 Aerospace series — nConnector optical ncircular single nchannel coupled nby self-locking ring noperating temperature n150 C continuous nPart 005 Receptacle conn.pdf

1、BS EN3733-005:2007ICS 49.060NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Connector, optical,circular, singlechannel, coupledby self-locking ring,operating temperature150 C continuousPart 005: Receptacle, connector, twohole fixing cable accord

2、ing to EN 4532,product standardLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/11/2008 02:12, Uncontrolled Copy, (c) BSIThis British Standard was published under theauthority of the StandardsPolicy and StrategyCommittee on 3 2008 BSI 2008ISBN 978 0 580 58506 7Amendments/corrigenda issued s

3、ince publicationDate CommentsBS EN 3733-005:2007National forewordThis British Standard is the UK implementation of EN 3733-005:2007.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic electrical and fibre optictechnology.A list of organizations repres

4、ented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.0SeptemberLicen

5、sed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/11/2008 02:12, Uncontrolled Copy, (c) BSIBS EN 3733-005:2007EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3733-005 December 2007 ICS 49.060 English Version Aerospace series - Connector, optical, circular, single channel, coupled by self-loc

6、king ring, operating temperature 150 C continuous - Part 005: Receptacle, connector, two hole fixing cable according to EN 4532, product standard Srie arospatiale - Connecteur optique circulaire monovoie, accouplement par bague filete, temprature dutilisation 150 C continu - Partie 005 : Embase coll

7、erette fixation par deux trous pour cble selon EN 4532, norme de produit Luft- und Raumfahrt - Optischer Rundsteckverbinder einpolig, Schraubkupplung, Betriebstemperatur 150 C konstant - Teil 005: Fester Steckverbinder, Zweilochbefestigung fr Kabel nach EN 4532, ProduktnormThis European Standard was

8、 approved by CEN on 16 September 2007. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such

9、national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language

10、and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxemb

11、ourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rig

12、hts of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3733-005:2007: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/11/2008 02:12, Uncontrolled Copy, (c) BSIBS EN 3733-005:2007EN 3733-005:2007 (E) 2 Contents Page Foreword3 1 Scope 4 2 N

13、ormative references 4 3 Terminology .4 4 Required characteristics.5 4.1 Dimensions and mass.5 4.2 Panel cut-out and mounting of connectors 5 4.3 Materials .7 4.4 Main general characteristics 7 4.5 Possible combinations of plugs and receptacles 7 5 Designation 7 6 Marking .8 7 Technical specification

14、 .8 Figures Figure 1 5 Figure 2 6 Figure 3 6 Tables Table 1 Compatible connectors and spare parts 7 Table 2 Additional test requirements applicable to this product standard 8 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/11/2008 02:12, Uncontrolled Copy, (c) BSIBS EN 3733-005:2007EN 3733

15、-005:2007 (E) 3 Foreword This document (EN 3733-005:2007) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of t

16、he National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2008, and conflicting nati

17、onal standards shall be withdrawn at the latest by June 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CEN

18、ELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem

19、bourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/11/2008 02:12, Uncontrolled Copy, (c) BSIBS EN 3733-005:2007EN 3733-005:2007 (E) 4 1 Scope This standard spec

20、ifies the characteristics of receptacle connectors with two hole fixing in the family of circular single channel fibre optic connectors incorporating ferrules for aerospace series single core optical cable in accordance with EN 4532. Connector interface dimensions, table of tests and qualification a

21、pproval requirements, are contained in the Technical Specification EN 3733-001. EN 3733-002, List of product standards, includes the listings of product types, codification and applicable combinations of product types. 2 Normative references The following referenced documents are indispensable for t

22、he application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591, Aerospace series Elements of electrical and optical connection Test methods General1)EN 2591-100,

23、Aerospace series Elements of electrical and optical connection Test methods Part 100: General EN 3733-001, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature 150 C continuous Part 001: Technical specification2)EN 3733-002, Aerospace ser

24、ies Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature 150 C continuous Part 002: List of product standards2) EN 3733-003, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature 150 C continuou

25、s Part 003: Plug connector for cable according to EN 4532, product standard2)EN 3733-007, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature 150 C continuous Part 007: Ferrule (optical contact) for cable according to EN 4532 (200 m/280

26、m fibre), product standardEN 3733-009, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 009: Receptacle sub-assembly for cable to EN 4532 (200 m/280 m fibre) Product standard EN 4532, Aerospace series Cable

27、s, optical, single core 200/280 m fibre, 2,5 mm outer jacket Technical specification2)MIL-STD-810F, Environmental Engineering Considerations and Laboratory Tests3)3 Terminology See EN 2591-100. 1) All parts quoted in Table 2. 2) Published as ASD prestandard at the date of publication of this standar

28、d. 3) Published by: Department of Defence (DOD), the Pentagon, Washington, DC 20301, USA. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/11/2008 02:12, Uncontrolled Copy, (c) BSIBS EN 3733-005:2007EN 3733-005:2007 (E) 5 4 Required characteristics 4.1 Dimensions and mass Dimensions shall b

29、e as shown in Figure 1. Dimensions in millimetres Mass: 14,0 g max. NOTE Terminated overall length assumes a maximum gap of 1 mm between crimp sleeve and rear nut. Key 1 Max. panel thickness rear mounted 2 2 holes 3 Thread 4 Max. panel thickness front mounted Figure 1 4.2 Panel cut-out and mounting

30、of connectors Panel cut-out and connector mounting details shall be as shown in Figures 2 and 3 respectively. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/11/2008 02:12, Uncontrolled Copy, (c) BSIBS EN 3733-005:2007EN 3733-005:2007 (E) 6 Dimensions in millimetres Key 1 Recommended 2 Typ

31、ical Figure 2 Front Mounting Rear Mounting Key 1 Screw head 2 Panel Figure 3 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/11/2008 02:12, Uncontrolled Copy, (c) BSIBS EN 3733-005:2007EN 3733-005:2007 (E) 7 4.3 Materials Nickel-copper alloy connector shell. 4.4 Main general characteristic

32、s See EN 3733-002. 4.5 Possible combinations of plugs and receptacles Compatibility shall be in accordance with Table 1 for combinations of connector and deliverable spares. Connectors terminated with cable to EN 4532 are only compatible with similarly terminated mating connectors. Table 1 Compatibl

33、e connectors and spare parts Subject connector Compatible mating connector Product standard EN 3733 Product type Product standardEN 3733 Product type 003 Plug connector Spare parts for 004 Product standardEN 3733 Product type 007 Ferrule 005 Receptacle, connector, two hole fixing 009 Receptacle sub-

34、assembly See also EN 3733-002 for combination of protective covers and connectors. 5 Designation EXAMPLE: Description block Identity block CONNECTOR, OPTICAL, RECEPTACLE EN 3733 005 B X Number of the basic standard Product standard (see EN 3733-002, product type) Class (see EN 3733-001, test fluids

35、class B) Polarization (see EN 3733-001) NOTE 1 Part number spacing as shown is for better readability only. NOTE 2 If necessary, the code I9005 may be placed between the description block and the identity block. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/11/2008 02:12, Uncontrolled Co

36、py, (c) BSIBS EN 3733-005:2007EN 3733-005:2007 (E) 8 6 Marking See EN 3733-001. 7 Technical specification See EN 3733-001 for technical requirements common to all product standards. See table 2 for additional testing applicable to this product standard (when mated with compatible connector terminate

37、d with cable in accordance with EN 4532). Table 2 Additional test requirements applicable to this product standard EN 2591 Designation of the test Details 6321 Optical elements Damp heat, cyclic test Number of cycles: 10 At the end of the seventh cycle, with connectors mated and subjected to humidit

38、y, insertion loss (EN 2591-601) shall be measured 0,85 dB. 6402 Optical elements Shock Severity: 300 g, Method A Number of shocks: Three shocks in each of two axes Optical discontinuity threshold shall be set at 0,85 dB with a minimum discontinuity of 20 ns. 6403 Optical elements Vibration Method B

39、modified as follows: Duration 8 h in two axes Figure 2, level J, except that the curve shall be altered to start with a value of 0,04 g2/Hz at 15 Hz and join the maximum PSD value at 50 Hz with a straight line. Optical discontinuity (EN 2591-602) Method B shall be monitored during the test with the

40、discontinuity threshold set at 0,85 dB. Direction of random vibration application Vertical and horizontal test axes Direction of shock application Vertical and horizontal test axes Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/11/2008 02:12, Uncontrolled Copy, (c) BSIBS EN 3733-005:2007E

41、N 3733-005:2007 (E) 9 Table 2 Additional test requirements applicable to this product standard (continued) EN 2591 Designation of the test Details See EN 3733-001 High level vibration e.g. gunfire MIL-STD-810F Method 519.3, Procedure 1, test spectra Figure 519.3-1 modified as follows: T1(g2/Hz) 0,05

42、0 T20,911 T32,803 Overall gRMS40,08 F1(Hz) 28,3 F2 (Hz) 56,5 F3(Hz) 84,9 F4(Hz) 113,2 P1(g2/Hz) 1,624 P21,764 P32,087 P42,806 Test duration shall be 26,5 min per axis (two axes). Optical discontinuity (EN 2591-602) Method B shall be monitored during conditioning with the discontinuity threshold set

43、at 0,85 dB. 6405 Optical elements Axial load Tensile load 200 N Optical elements Insertion loss Initial measurement (prior to conditioning): 0,6 dB Post conditioning: 0,85 dB Wavelength of measurement: 810 nm Launch condition: Overfill 601 Variation of insertion loss Where specified in EN 3733, Tabl

44、e 5 as part of a test requirement, the variation of insertion loss shall be monitored with a maximum change 0,25 dB. 602 Optical elements Variation of attenuation and optical discontinuity There shall be no discontinuities 20 ns and not more than one discontinuity every 500 s. The discontinuity thre

45、shold shall be set at 0,85 dB. 609 Optical elements Effectiveness of cable attachment Cable cyclic flexing 100 cycles, 5 N tensile load, pendulum arm length 0,62 m. Direction of high level vibration application Vertical and horizontal test axes Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS,

46、18/11/2008 02:12, Uncontrolled Copy, (c) BSIBS EN 3733-005:2007EN 3733-005:2007 (E) 10 Table 2 Additional test requirements applicable to this product standard (concluded) EN 2591 Designation of the test Details 610 Optical elements Effectiveness of cable attachment Cable pulling 10 cycles, 200 N 61

47、1 Optical elements Effectiveness of cable attachment Cable torsion Tensile load applied to cable during torsion application 5 N. 612 Optical elements Effectiveness of cable attachment Cable axial compression Load: 10 N Application rate: 100 N/min Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS

48、, 18/11/2008 02:12, Uncontrolled Copy, (c) BSIBS EN 3733-005:2007This page has been intentionally left blankLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/11/2008 02:12, Uncontrolled Copy, (c) BSIBS EN3733-005:2007BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20

49、 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oredi