BS EN 3841-406-2005 Aerospace series - Circuit breakers - Test methods - Flammability《航空航天系列 断路器 试验方法 易燃性》.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS EN 3841-406:2004 Circuit breakers Test methods Part 406: Flammability The European Standard EN 3841-406:2004 has the status of a British Standard ICS 49.060 BS EN 3841-406:2004 This British Standard was published under the authority of the Standards Policy and St

2、rategy Committee on 21 February 2005 BSI 21 February 2005 ISBN 0 580 45536 X National foreword This British Standard is the official English language version of EN 3841-406:2004. The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibr

3、e optic technology, to Subcommittee ACE/6/5, Circuit breakers, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred

4、 to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provision

5、s of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or

6、proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 4, an inside back cover and a back cover. The

7、BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN3841406 December2004 ICS49.060 Englishversion AerospaceseriesCircuitbreakersTestmethodsPart406: Flam

8、mability SriearospatialeDisjoncteursMthodesdessais Partie406:Ininflammabilit LuftundRaumfahrtSchutzschalterPrfverfahrenTeil 406:Nichtentflammbarkeit ThisEuropeanStandardwasapprovedbyCENon10September2004. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgiv

9、ingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninan

10、yotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland

11、,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2004CEN Allrigh

12、tsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.EN3841406:2004:E EN 3841-406:2004 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Method 4 4 Requirement.4 EN 3841-406:2004 (E) 3 Foreword This document (EN 3841-406:2004) has been prepared by th

13、e European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, p

14、rior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2005, and conflicting national standards shall be withdrawn at the latest by June 2005. According to the CEN/C

15、ENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, M

16、alta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 3841-406:2004 (E) 4 1 Scope This standard specifies a method of verifying the flammability of plastic (synthetic) materials used in the housing, insulator base and any parts exposed to

17、arcs or glowing elements of circuit breakers. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any a

18、mendments) applies. IEC 60695-2-10, Fire Hazard Testing Part 2-10: Glowing/Hot-Wire Based Test Methods Glow/Wire Apparatus and Common Test Procedure 3 Method The test apparatus is described in IEC 60695-2-10, clause 4 and Figure 2. The glow-wire test shall be carried out in accordance with IEC 60695

19、-2-10 and the following requirements: the tested parts shall be fitted with the tip of the glow-wire positioned at a distance of (200 5) mm above the white board (approximately 10 mm thick and covered with a single layer of tissue paper); the test shall be carried out on part supporting current carr

20、ying parts (main and signal) and parts of the housing in contact with electric arcs; temperature of the tip of the glow-wire: (960 15) C; duration of application: (30 1) s. 4 Requirement The test shall be considered to be satisfactory if a flame or glowing of the tested part is extinguished within 3

21、0 s of removing the glow-wire and if there is no ignition of the tissue paper. blankBS EN 3841-406:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in

22、 Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our

23、products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 74

24、00. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996

25、 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise reque

26、sted. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and service

27、s. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Mem

28、bership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Cop

29、yright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted

30、 in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.