BS EN 4111-2006 Wrenches splined sockets for pipe fittings - Technical specification《航空航天系列 管件的花键套筒扳手 技术规范》.pdf

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58specification The European Standard EN 4111:2006 has the status of a British StandardICS 49.030.99W

2、renches, splined, socket for pipe fittings Technical BRITISH STANDARD AEROSPACE SERIESBS EN4111:2006BS EN 4111:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2006 BSI 2006ISBN 0 580 48531 5Cross-referencesThe British Standards wh

3、ich implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publica

4、tion does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, t

5、he EN title page, pages 2 to 8, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsA list of organizations represented on this committee can be obtained on requ

6、est to its secretary. present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.National forewordThis British Standard

7、 is the official English language version of EN 4111:2006. The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems, which has the responsibility to: aid enquirers to understand the text;EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE

8、NORMEN 4111May 2006ICS 49.030.99English VersionAerospace series - Wrenches, splined, socket for pipe fittings -Technical specificationSrie arospatiale - Cls et embouts cannels, tuyauter -Spcification techniqueLuft- und Raumfahrt - Ringschlssel, offen, verzahnt -Technische LieferbedingungenThis Europ

9、ean Standard was approved by CEN on 6 February 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references conc

10、erning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own la

11、nguage and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Ma

12、lta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploi

13、tation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 4111:2006: E2 Contents Page Foreword 3 1 Scope .4 2 Normative references .4 3 Terms and definitions.4 4 Required characteristics 4 5 Test methods.5 6 Quality assurance .6 7 Marking/packaging6 EN 4111:20063 For

14、eword This European Standard (EN 4111:2006) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associa

15、tions and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2006, and conflicting national standard

16、s shall be withdrawn at the latest by November 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Inte

17、rnal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Nethe

18、rlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 4111:20064 1 Scope This standard specifies the requirements which must be met by hand-operated splined wrenches and sockets for aerospace applications. 2 Normative references The foll

19、owing referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4156, Straight cylindrical involute splines Metric mo

20、dule, side fit Generalities, dimensions and inspection. ISO 6508 (all parts), Metallic materials Rockwell hardness test. EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard parts. 3 Terms and definitions For the purposes of this standard, the following

21、 terms and definitions apply. 3.1 batch a batch consists of wrenches or sockets of the same types and of the same materials defined by the same standard 4 Required characteristics 4.1 Materials The materials shall meet the required characteristics specified in the product standard. 4.2 Physical char

22、acteristics 4.2.1 Surface condition/appearance The hand-operated wrenches or sockets shall be free from pitting, deposits, forging flashes, cracks, splits, burrs and other defects liable to impair their characteristics and their endurance and to cause injury to operators. 4.2.2 Surface coating The s

23、urface coating shall be that laid down in the product standard. 4.2.3 Characteristics of the inner profile of the splines All of the splines shall be free from burrs and rough spots. The surface roughness is specified in the product standard. EN 4111:20065 4.3 Mechanical characteristics The strength

24、 and endurance of the various types of wrench are tested by torque tests, the procedures for which are described in Clause 5. At the end of the strength and endurance test, the wrenches or sockets shall not exhibit deterioration or distortion as defined below: The tips of the splines shall not exhib

25、it rounding or fretting and shall be in accordance with the characteristics described in 4.2.3; The wrench or socket shall be free from cracks; The general surface condition shall be in accordance with the requirements of 4.2.1; Distortion of more than 0,05 mm of the outer diameter of the sockets an

26、d wrench heads; The surface coating shall show no significant sign of deterioration or flaking; Permanent distortion of the wrench handle of more than 5; A Rockwell hardness test (ISO 6508) shall demonstrate values in accordance with the values indicated in the product standard. 4.4 Dimensions and t

27、olerances The dimensions and tolerances shall be in accordance with requirements of the product standard. 5 Test methods 5.1 Test equipment The wrenches or sockets are fitted on a splined test mandrel. The mandrel dimensions for a relevant wrench shall be based on the maximum corresponding values fo

28、r an external 45 pressure angle side fit root radius 6H spline to ISO 4156, and a hardness of 60 HRC. 5.2 Test on splined wrenches and sockets The wrenches or sockets shall be fully engaged on the mandrel; during the test, the wrench shall be moved smoothly without knocks and jerks. The load shall b

29、e applied as far away as possible on the arm of the wrench or at the driving square of the sockets, perpendicularly to the axis, continuously and progressively up to the torque value appropriate to the wrench under test. 5.3 Conduct of the test On each wrench or socket tested, carry out a cycle of 5

30、00 applications, at maximum rate of 60 per minute, at the endurance torque indicated in Table 1. At the end of each 100 applications, apply the resistance torque, which is equivalent to 1,5 times the endurance torque indicated in Table 1, and move the wrench 1/8 of a turn. In the case of double-ende

31、d wrenches, each end shall be tested. EN 4111:20066 Table 1 Resistance and endurance torque values DN aResistance torque Nm Endurance torque Nm 4 27 18 6 42 288 48 3210 54 36 12 62 4213 66 4414 71 47 16 83 5518 98 6520 128 85 22 5 1025 188 125 32 21 14aDN: Diameter Nominal (outside diameter of the c

32、orresponding pipe) 6 Quality assurance 6.1 Qualification EN 9133: Requirement for ISO 9000:2000 not applicable. Qualification tests specified in this document shall be applied to each type and each dimensional combination of wrench of socket in accordance with Tables 2 and 3. Some or all of these te

33、sts may also be used for acceptance of function where a more comprehensive test proves necessary. 6.2 Acceptance The aim of the acceptance tests is to check, as simply as possible, that wrenches or sockets from different batches satisfy the requirements of this standard. The acceptance tests shall b

34、e conducted on wrenches or sockets chosen at random from different production batches in accordance with Tables 4 and 5. 7 Marking/packaging 7.1 Marking The marking is specified in the product standard. EN 4111:20067 7.2 Packaging The packaging of the wrenches or sockets is left to the choice of the

35、 manufacturers. Table 2 Summary of qualifications and production acceptance tests Qualification Production acceptance Characteristics Clause Sample size Clause Sample size Non destructive Dimensions and tolerances 4.4 5 4.4 Table 4 Marking 7.1 5 Surface condition/appearance 4.2.1 5 4.2.1 Table 4 Sur

36、face coating 4.2.2 2 Characteristics of the inner profile of the splines 4.2.3 2 4.2.3 Table 4 Destructive Test methods 5 4 5 Table 5 Mechanical characteristics 4.3 4 Table 3 Qualification tests for each size of wrench or socket sample Wrench or socket sample number Type of test Defined in1 2 3 4 5

37、Non destructive Dimensions and tolerances 4.4 X X X X X Marking 7.1 X X X X X Surface condition/appearance 4.2.1 X X X X X Surface coating 4.2.2 X X Characteristics of the inner profile of the splines 4.2.3 X X Destructive Test methods 5 X X X X Mechanical characteristics 4.3 X X X X EN 4111:20068 T

38、able 4 Sampling plans for visual inspections and dimensional characteristics Acceptance number (Ac) and limiting quality (LQ) in accordance with the acceptable quality level (AQL) AQL 2,5 % Batch size Sample size Ac LQ10% 20 3 21 to 50 5 51 to 90 8 0 91 to 150 10 1 90 151 12 2 80 Table 5 Sampling pl

39、ans for torque test Sample size Destructive test Production size Wrench Socket 20 21 to 50 0 0 51 to 90 91 to 150 1 2 a1 151 2 2 aaAt each end EN 4111:2006blankBS EN BSI389 Chiswick High RoadLondonW4 4AL4111:2006BSI British Standards InstitutionBSI is the independent national body responsible for pr

40、eparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editio

41、ns.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the insid

42、e front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications s

43、hould be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have

44、been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also ava

45、ilable which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standa

46、rds. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is avai

47、lable on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced

48、, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type o

49、r grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.