ImageVerifierCode 换一换
格式:PDF , 页数:10 ,大小:280.66KB ,
资源ID:551478      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-551478.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(BS EN 4306-2005 Sleeves tubular for tension screws with flush head in corrosion resisting steel passivated (0 50 mm wall thickness)《钝化耐腐蚀钢制埋头张力螺钉用套管(0 50毫米壁厚)》.pdf)为本站会员(confusegate185)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

BS EN 4306-2005 Sleeves tubular for tension screws with flush head in corrosion resisting steel passivated (0 50 mm wall thickness)《钝化耐腐蚀钢制埋头张力螺钉用套管(0 50毫米壁厚)》.pdf

1、BRITISH STANDARD AEROSPACE SERIESBS EN 4306:2005Sleeves, tubular, for tension screws with flush head, in corrosion resisting steel, passivated, (0,50 mm wall thickness)The European Standard EN 4306:2005 has the status of a British StandardICS 49.030.99g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g5

2、6g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Mon May 08 07:08:28 BST 2006, Uncontrolled Copy, (c) BSIBS EN 4306:2005This British Standard was published under the au

3、thority of the Standards Policy and Strategy Committee on 17 February 2006 BSI 17 February 2006ISBN 0 580 47749 5National forewordThis British Standard is the official English language version of EN 4306:2005. The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aeros

4、pace fasteners and fastening systems, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be fo

5、und in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are resp

6、onsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep

7、UK interests informed; monitor related international and European developments and promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 7 and a back cover.The BSI copyright notice displayed in this document indicates wh

8、en the document was last issued.Amendments issued since publicationAmd. No. Date CommentsLicensed Copy: Wang Bin, na, Mon May 08 07:08:28 BST 2006, Uncontrolled Copy, (c) BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 4306December 2005ICS 49.030.99English VersionAerospace series - Sleeves, tub

9、ular, for tension screws withflush head, in corrosion resisting steel, passivated, (0,50 mmwall thickness)Srie arospatiale - Douilles tubulaires, pour vis de traction tte fraise, en acier rsistant la corrosion, passives,(paisseur de paroi 0,50 mm)Luft- und Raumfahrt - Hlsen fr Senkschrauben mitZugbe

10、anspruchung, aus korrosionsbetndigem Stahl,passiviert, (Wanddicke 0,50 mm)This European Standard was approved by CEN on 26 October 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national s

11、tandard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other

12、language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,

13、Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagemen

14、t Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 4306:2005: ELicensed Copy: Wang Bin, na, Mon May 08 07:08:28 BST 2006, Uncontrolled Copy, (c) BSI2 Contents Page Foreword 3 1 Scope .4

15、 2 Normative references .4 3 Terms and definitions.4 4 Required characteristics 4 5 Designation .7 6 Marking 7 7 Technical specification.7 EN 4306:2005Licensed Copy: Wang Bin, na, Mon May 08 07:08:28 BST 2006, Uncontrolled Copy, (c) BSI3 Foreword This European Standard (EN 4306:2005) has been prepar

16、ed by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of

17、AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2006, and conflicting national standards shall be withdrawn at the latest by June 2006. Attention is d

18、rawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the follo

19、wing countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden

20、, Switzerland and the United Kingdom. EN 4306:2005Licensed Copy: Wang Bin, na, Mon May 08 07:08:28 BST 2006, Uncontrolled Copy, (c) BSI4 1 Scope This standard specifies the characteristics and technical requirements of tubular sleeves for tension screws with flush head, which may be plain or provide

21、d with a series of annular grooves, in corrosion resisting steel, passivated, with a 0,50 mm wall thickness, for maximum operating temperature 650 C, for aerospace applications. 2 Normative references The following referenced documents are indispensable for the application of this document. For date

22、d references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspe

23、ction. EN 2175, Aerospace series Heat resisting alloy FE-PA2602 (X4NiCrTiMoV26-15) Solution treated and precipitation treated Sheet, strip and plate 0,5 mm a 10 mm Rm 850 MPa. 1)EN 2424, Aerospace series Marking of aerospace products. EN 2516, Aerospace series Passivation of corrosion resisting stee

24、ls and decontamination of nickel base alloys. 3 Terms and definitions For the purposes of this standard, the following terms and definitions apply. 3.1 crack rupture in the matrial which may extend in any direction and which may be intercrystalline or transcrystalline in character 3.2 seam open surf

25、ace defect which is the result of the extrusion of the matrial 3.3 lap surface defect caused by folding over metal fins or sharp corners and then rolling or forging them into the surface 4 Required characteristics 4.1 Configuration - Dimensions - Masses See Figure 1 and Tables 1 and 2. Dimensions an

26、d tolerances are expressed in millimetres and apply after surface treatment. 1) Published as AECMA Prestandard at the date of publication of this standard. EN 4306:2005Licensed Copy: Wang Bin, na, Mon May 08 07:08:28 BST 2006, Uncontrolled Copy, (c) BSI5 4.2 Material EN 2175, received in the anneale

27、d condition and cold work during manufacture 4.3 Surface treatment EN 2516 Values in micrometres apply prior to surface treatment. Remove sharp edges 0,1 to 0,2. Key 1 Z: Number of grooves. The Pitch of groove = 2 aUnspecified dimensions: as plain form bAt manufacturers option cForm of groove at man

28、ufacturers option Figure 1 Plain form (code “P“) Grooved form (code “G“) a3,2 0,8 EN 4306:2005Licensed Copy: Wang Bin, na, Mon May 08 07:08:28 BST 2006, Uncontrolled Copy, (c) BSI6 Table 1 D1D2D3L2L3L4L5R Z Diameter codemax. min. 0,3 max. min. 0,5 0,5 + 0,25 0,05 060 5,999 5,96 12 6,999 7,974 2,6 2,

29、84 4 7 080 7,994 7,955 16 8,994 8,97 3,4 3,64 7 6 100 9,994 9,955 20 10,994 10,97 4,2 4,44 6 10 5 120 11,994 11,995 24 12,994 12,97 5 5,24 0,75 Table 2 Diameter code 060 080 100 120 Length Form code acode L1050,+Mass b045 4,5 0,564 060 6 0,684 0,842 075 7,5 0,805 0,999 1,316 090 9 0,925 1,156 1,510

30、1,896 105 10,5 1,046 1,313 1,705 2,127 120 12 1,166 1,470 1,899 2,358 135 13,5 1,287 1,627 2,094 2,589 150 15 1,407 1,784 2,288 2,820 165 16,5 1,528 1,941 2,483 3,051 180 18 1,648 2,098 2,677 3,282 195 19,5 1,769 2,255 2,872 3,513 210 21 1,889 2,412 3,066 3,744 225 22,5 2,010 2,559 3,261 3,975 240 2

31、4 2,130 2,726 3,456 4,206 P 250 25 2,210 2,831 3,586 4,360 G 250 25 2,210 2,831 3,586 4,360 aSee Figure 1. bApproximate values (kg/1 000 pieces), calculated on the basis of 7,85 kg/dm3, given for information purposes onlyEN 4306:2005Licensed Copy: Wang Bin, na, Mon May 08 07:08:28 BST 2006, Uncontro

32、lled Copy, (c) BSI7 5 Designation EXAMPLE Description block SLEEVE Identity block EN4306P060045 Number of this standard Form code (see Table 2 and Figure 1) Diameter code (see Table 1) Length code (see Table 2) NOTE If necessary, the code I9005 shall be placed between the description block and the i

33、dentity block. 6 Marking EN 2424, style G 7 Technical specification 7.1 Manufacture The sleeves shall be formed by a drawing process from sheet or strip stock to form a one piece tubular section and head. 7.2 Surface appearance The sleeves shall be free from cracks, seams and laps. Under visual exam

34、ination, the sleeves may show axial flow lines in the tubular section typical of a drawn sleeve. The flow lines shall be continuous at the fillet radius. A slight visible orange peel effect is also permissible. 7.3 Sampling In conformity with ISO 2859-1, using normal or reduced inspection methods. T

35、he acceptance quality limit (AQL) is 1 %. EN 4306:2005Licensed Copy: Wang Bin, na, Mon May 08 07:08:28 BST 2006, Uncontrolled Copy, (c) BSIBS EN 4306:2005BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Stand

36、ards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant

37、 aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +

38、44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to

39、 Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as Bri

40、tish Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give det

41、ails on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of t

42、hese and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI webs

43、ite at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retriev

44、al system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations.

45、 If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.Licensed Copy: Wang Bin, na, Mon May 08 07:08:28 BST 2006, Uncontrolled Copy, (c) BSI

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1