BS EN 4421-2007 Aerospace series - Studs in titanium alloy TI-P64001 MoS2 coated with serrated locking ring in corrosion resisting steel - Strength class 1100 MPa(at ambient temper.pdf

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58with serrated locking ring in corrosion resisting steel Strength class: 1 100 MPa (at ambient tempe

2、rature)The European Standard EN 4421:2007 has the status of a British StandardICS 49.030.20Aerospace series Studs, in titanium alloy TI-P64001, MoS2 coated, BRITISH STANDARDBS EN 4421:2007BS EN 4421:2007This British Standard was published under the authority of the Standards Policy and Strategy Comm

3、ittee on 31 August 2007 BSI 2007ISBN 978 0 580 55643 2Amendments issued since publicationAmd. No. Date CommentsCompliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standard is the UK implementation of EN 4421:2007. The UK participation in its

4、 preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are res

5、ponsible for its correct application.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4421 June 2007 ICS 49.030.20 English Version Aerospace series - Studs, in titanium alloy TI-P64001, MoS2coated, with serrated locking ring in corrosion resisting steel - Strength class: 1 100 MPa (at ambient te

6、mperature) Srie arospatiale - Goujons, en alliage de titane TI-P64001, revtus MoS2, avec bague de verrouillage dentele, en acier rsistant la corrosion - Classe de rsistance: 1 100 MPa ( temprature ambiante) Luft- und Raumfahrt - Stiftschrauben, aus Titanlegierung TI-P64001, MoS2beschichtet, mit Ring

7、sicherung aus korrosionsbestndigem Stahl - Festigkeitsklasse: 1 100 MPa (bei Raumtemperatur) This European Standard was approved by CEN on 26 October 2005. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the s

8、tatus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German)

9、. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Repu

10、blic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE

11、 NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4421:2007: E2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Re

12、quired characteristics.4 3.1 Configuration Dimensions Tolerances Masses4 3.2 Materials .4 3.3 Surface treatment 4 4 Designation 6 5 Marking .6 6 Technical specification .6 EN 4421:20073 Foreword This document (EN 4421:2007) has been prepared by the Aerospace and Defence Industries Association of Eur

13、ope - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has re-ceived the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European St

14、andard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2007, and conflicting national standards shall be withdrawn at the latest by December 2007. Attention is drawn to the possibility that some of the elements

15、 of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Europe

16、an Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Repub-lic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United

17、Kingdom. EN 4421:20074 1 Scope This standard specifies the characteristics of studs in TI-P64001, MoS2coated, with serrated locking ring in corrosion resisting steel for aerospace applications. Strength class: 1 100 MPa1)2 Normative references The following referenced documents are indispensable for

18、 the application of this document. For dated refer-ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products EN 3311, Aerospace series Titanium alloy TI-P640

19、01 Annealed Bar for machining D 150 mm 2)EN 4458, Aerospace series Studs, MJ threads, in titanium alloy TI-P64001, MoS2coated, with serrated locking ring in corrosion resisting steel Strength class: 1 100 MPa (at ambient temperature) Technical specification ISO 3353, Aerospace Rolled threads for bol

20、ts Lead and runout requirements ISO 5855-2, Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts AMS 5604R, Steel, corrosion resistant, bars, wire, and forgings 18 Cr 9.0 Ni free machining3)3 Required characteristics 3.1 Configuration Dimensions Tolerances Masses See Figure 1 and Tables

21、1 and 2. Dimensions and tolerances are in millimetres. They apply before MoS2coating. 3.2 Materials Stud: EN 3311 Ring: AMS 5640 3.3 Surface treatment EN 2491 1) Minimum tensile strength of the material at ambient temperature 2Published as ASD Prestandard at the date of publication of this standard

22、3) Published by: Society of Automotive Engineers, Inc. (SAE), 400 Commonwealth Drive, Warrendale, PA 15096-0001, USA EN 4421:20075 Remove sharp edges 0,1 to 0,4 Ring outer serration Key 1 Nut end threads 2 Pitch diameter 3 Diameter D before rolling 4 Two pitches maximum, runout threads 5 Installatio

23、n on threads 6 Marking 7 N: theoretical number of teeth aLocking ring seating against the nut end thread bOptional locking ring guide cRolled dUsed to identify the nut end thread when locking ring guide has been removed eDeletion of a tooth for optional metric identification of stud fBlending radius

24、 0,1 to 0,2 Figure 1 Table 1 Thread aA B D E G H J K M N R Code Designation 0,5 min. min. max. max. min. max. min. 2 max. max. min. 050 MJ5 0,8 4h6h 11 7,50 4,50 1,65 5,16 6,85 6,65 7,85 7,70 2,50 0,45 0,35060 MJ6 1 4h6h 13,50 9 5,30 2,35 6,19 7,85 7,65 8,85 8,70 100 3,20 15 0,50 0,40aIn accordance

25、with ISO 5855-2. EN 4421:20076 Table 2 Thread code L 050 060 C F C F Length code 0,4 min. max. Mass amin. max.Mass a010 10 7 2,05 012 12 9 2,20 8 3,44 014 14 11 3 2,34 10 3,66 016 16 11,5 2,49 12 4 3,87 018 18 13,5 4,25 2,63 12,5 4,07 020 20 6,25 2,78 14,5 5,3 4,28 022 22 8,25 2,92 7,3 4,48 025 25 1

26、1,25 3,13 10,3 4,77 028 28 14,25 3,34 13,3 5,08 030 30 16,25 3,48 15,3 5,26 035 35 21,25 3,84 20,3 5,76 040 40 14 26,25 4,19 15 25,3 6,25 aMass quoted in kg/1 000 parts. 4 Designation EXAMPLE Description block Identity block STUD EN4421050 025 Number of this standard Thread code (see Table 1) Length

27、 code (see Table 2) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 5 Marking EN 2424, style A, as indicated on Figure 1. 6 Technical specification EN 4458, plus ring rotational integrity test. EN 4421:2007blankBS EN BSI389 Chiswick High RoadLo

28、ndonW4 4AL4421:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment

29、 or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would i

30、nform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest e

31、ditions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response t

32、o orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Li

33、brary and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are ke

34、pt up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to

35、British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization

36、 bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the f

37、ree use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.