BS EN 4424-2006 Aerospace series - Rod-ends adjustable single fork and threaded shank with engagement 1 5 x thread diameter in titanium alloys - Dimensions and loads《航空航天系列 钛合金接合螺纹.pdf

1、BRITISH STANDARD AEROSPACE SERIES BS EN 4424:2006 Rod-ends, adjustable, single fork and threaded shank with engagement: 1,5 thread diameter in titanium alloys Dimensions and loads The European Standard EN 4424:2006 has the status of a British Standard ICS 49.035 BS EN 4424:2006 This British Standard

2、 was published under the authority of the Standards Policy and Strategy Committee on 30 June 2006 BSI 2006 ISBN 0 580 48437 8 National foreword This British Standard is the official English language version of EN 4424:2006. The UK participation in its preparation was entrusted to Technical Committee

3、 ACE/12, Aerospace fasteners and fastening systems, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related interna

4、tional and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found i

5、n the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsi

6、ble for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 7 and a back cover. The BSI copyright notice displayed in this d

7、ocument indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN4424 June2006 ICS49.035 EnglishVersion AerospaceseriesRodends,adjustable,singleforkand threadedshankwithengagement:1,5threaddiameterin titan

8、iumalloysDimensionsandloads SriearospatialeEmboutsrglableschapesimpleet tigefileteimplantation:1,5diamtrefiletageen alliagesdetitaneDimensionsetcharges LuftundRaumfahrtEinstellbareGabelkpfe,einfach,mit GewindeschaftmitEinschraubtiefe1,5 GewindedurchmesserausTitanlegierungenMaeund Belastungen ThisEur

9、opeanStandardwasapprovedbyCENon20April2006. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtaine

10、donapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions.

11、CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Romania, Slovakia,Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPE

12、ANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2006CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.EN4424:2006:EEN 4424:2006 2 Contents Page Foreword3 1 Scope 4 2 No

13、rmative references 4 3 Required characteristics.4 4 Designation 6 5 Marking .7 6 Technical specification .7 EN 4424:2006 3 Foreword This European Standard (EN 4424:2006) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes

14、 carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, e

15、ither by publication of an identical text or by endorsement, at the latest by December 2006, and conflicting national standards shall be withdrawn at the latest by December 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN

16、 and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Den

17、mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. 4 1 Scope This standard specifies the characteristics of rod

18、-ends for flight control rods. a single fork; a threaded shank comprising; a circumferential groove to identify engagement; an optional longitudinal groove for locking purpose. These rod-ends are intended for use with control rods or rods for aircraft structures. 2 Normative references The following

19、 referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3353-1, Aerospace Lead and runout threads Part 1: Rolled e

20、xternal threads. ISO 5855-2, Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts. EN 2601, Aerospace series Fork ends, adjustable Technical specification. EN 3315, Aerospace series Titanium alloy TI-P64001 Solution treated and aged Forgings D e 75 mm. 1)EN 3353 2) , Aerospace series Tit

21、anium alloy TI-P63 Solution treated and aged R m 1100 MPa Bar and wire for fasteners machined D e 25 mm. 1)EN 3813, Aerospace series Titanium alloy TI-P64001 Annealed Bar and wire for forged fasteners D e 25 mm.1)TR 3775, Aerospace series Bolts and pins Materials. 3)3 Required characteristics 3.1 Di

22、mensions Masses Configuration shall correspond with Figure 1. The dimensions and masses shall conform with values quoted in Table 1. 3.2 Surface roughness According to Figure 1. 1) Published as AECMA Prestandard at the date of publication of this standard. 2) Inactive for new design, see EN 3813. 3)

23、 Published as AECMA Technical Report at the date of publication of this standard. EN 4424:20065 3.3 Material Titanium alloy according to EN 3315 or EN 3353 or TR 3775 R m 830 MPa on the whole rod-end. aThread bIn complete thread according to ISO 3353 cMarking dGroove diameter d 3min according to ISO

24、 5855-2 NOTE The circumferential groove and the longitudinal groove over distance F shall be painted red. Figure 1 EN 4424:20066 Table 1 Dimensions in millimetres Fork d 1r 1d 2d 3l 1l 2l 3l 4l 5r 2Code Nominal diameter J7 + 0,2 0 0,25 0,25 + 0,1 0 + 0,2 0 0,25 0,1 + 1 0 06 6 12,2 13 19,2 14 20,2 30

25、 24 0,5 08 8 13,9 15 21,5 15 22,2 36 30 2 10 10 17,8 17 27,0 20 28,2 41 34 0,8 3 Shank Rod-end Threadadesignation d 3l 6 bl 7l 8l 9l 10l 11r 3Ultimate load 0 0,25 min. + 1 0 + 0,1 0 0 0,1 0 1 max. kN Mass g MJ101,254h6h 23 39 8,0 33 40 31 MJ121,254h6h 27 44 2,4 10,2 38 0,8 58 46 MJ141,5 4h6h 4 31 50

26、 3,2 12,2 40 44 1,0 83 75 aAccording to ISO 5855-2; manufacturing method: rolled. bl 6is also the minimum length of engaged thread; it includes thickness of lock washers and height of nut. 4 Designation Each tab washer shall only be designated as in the following example: EXAMPLE Description block R

27、OD-END Identity block EN4424L08K Number of EN standard Code for thread direction (see Table 2) Diameter code (see Table 1) Code for longitudinal groove (see Table 2) EN 4424:20067 Table 2 Codes for thread direction and longitudinal groove Left hand thread L Right hand thread R With longitudinal groo

28、ve K Without longitudinal groove T NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 5 Marking In addition to the manufacturers own marking, each rod-end and its packaging shall be marked according to Figure 1, using the identity block as defined

29、 in Clause 4 of this standard. The marking shall be indelible and shall not impair the characteristics of the rod-end. 6 Technical specification According to EN 2601. EN 4424:2006BS EN 4424:2006 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent nationa

30、l body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the

31、latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of whi

32、ch can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and f

33、oreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI im

34、plementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic

35、 information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discou

36、nts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/ww

37、w.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and

38、 Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of nece

39、ssary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.