BS EN 4460-2005 Aerospace series - Studs in titanium alloy TI-P64001 with serrated locking ring in corrosion resisting steel - Installation and removal procedure《航空航天系列 钛合金TI-P6400.pdf

1、BRITISH STANDARD AEROSPACE SERIESBS EN4460:2005Studs, in titanium alloy TI-P64001, with serrated locking ring in corrosion resisting steel Installation and removal procedureThe European Standard EN 4460:2005 has the status of a British StandardICS 49.030.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43

2、g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 4460:2005This British Standard was published under the authority of the Standards Policy and Strategy Committee on 2 December 2005 BSI 2

3、December 2005ISBN 0 580 47330 9National forewordThis British Standard is the official English language version of EN 4460:2005.The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems, which has the responsibility to: A list of or

4、ganizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Corres

5、pondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of

6、 itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and

7、promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date Co

8、mmentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 4460October 2005ICS 49.030.20English VersionAerospace series - Studs, in titanium alloy TI-P64001, withserrated locking ring in corrosion resisting steel - Installation andremoval procedureSrie arospatiale - Goujons, en alliage de titane TI-P64

9、001, avec bague de verrouillage dentele en acierrsistant la corrosion - Procdure dinstallation etdextractionLuft- und Raumfahrt - Stiftschrauben, aus TitanlegierungTI-P64001, mit Ringsicherung aus korrosionsbestndigemStahl - Ein- und AusbauverfahrenThis European Standard was approved by CEN on 26 Se

10、ptember 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be ob

11、tained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secr

12、etariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portu

13、gal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and by any means reservedworl

14、dwide for CEN national Members.Ref. No. EN 4460:2005: E2 Contents Page Foreword 3 1 Scope .4 2 Normative references .4 3 Installation hole.4 4 Inspection requirements before installation.6 5 Installation tools .6 6 Stud removal and replacement 8 EN 4460:20053 Foreword This European Standard (EN 4460

15、:2005) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of th

16、e member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2006, and conflicting national standards shall be withdrawn at the latest by Ap

17、ril 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards or

18、ganizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,

19、 Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 4460:20054 1 Scope This standard specifies the conditions of installation and removal of studs with serrated locking ring in corrosion resisting steel defined by EN 4421, for aerospace applications. 2 Normative references The following

20、 referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 4421, Aerospace series Studs, in titanium alloy TI-P64001,

21、MoS2coated, with serrated locking ring in corrosion resisting steel Strength class: 1 100 MPa (at ambient temperature). 1)EN 4459, Aerospace series Studs, in titanium alloy TI-P64001, with serrated locking ring in corrosion resisting steel Design standard. 3 Installation hole 3.1 General Installatio

22、n hole is either fully defined or codified on the design drawing. Codification references the EN design standard in which the installation hole definition is given. Table 1 provides the cross reference between the insert codification, the stud threads, the tapped hole reference and the tapped hole w

23、ith serration reference. Table 1 Stud reference without length code Stud thread diameter Identity block of tapped hole Identity block of tapped hole with serration aEN4421-050 MJ50,8 EN4459-050 EN4459-050-S EN4421-060 MJ61 EN4459-060 EN4459-060-S aSee 3.2 for hole serration manufacture. 3.2 Hole dri

24、lling Drilling of pilot hole for tapping and counterboring shall be carried out in conformity with the drawing and can be carried out with a step drill if the specified pilot hole length allows it. For casings in aluminium alloy and in magnesium alloy, a spotfacing is specified. 1) Published as AECM

25、A Prestandard at the date of publication of this standard. EN 4460:20055 3.3 Broaching If drawing specifies manufacture of serration intended to facilitate assembly in hard materials they will be carried out for obtaining serration defined in Figures 1 and 2 and Table 2 in the spotfacing of the inst

26、allation hole. Table 2 Dimensions in millimetres Dimensions K R2AA AB AC AD AE Associated bolt thread max. min. max. J Number of serrationsMJ50,8 0,34 7,8 7,44 2,6 2,2 MJ61 0,43 9,01 8,54 0,06 76 3,3 2,9 0,10 15 Key 1 Serration form at this position may vary (within the profile tolerance) due to bro

27、ach wear. Figure 1 Figure 2 EN 4460:20056 4 Inspection requirements before installation Prior to installation check the installation hole, counterbore and serration (when applicable) to receive the insert are free from burrs and any foreign objects, grease, oil, etc. Inspect stud to be installed and

28、 ensure that it is clean and free from protective grease, etc. Studs installed in aluminium alloy components shall be lightly smeared externally with a suitable compound to prevent electrolytic corrosion. 5 Installation tools 5.1 General The tools and their methods of application described in this s

29、tandard are not mandatory and show only the basic principles to be observed to achieve the satisfactory installation or removal of the studs. The minimum dimensional requirements provided shall be achieved and on no account shall the design of the tools or their methods of application be such that d

30、amage may occur to the threads of the stud or the component into which it is being installed. Always ensure the appropriate tool/stud size combinations have been chosen to enable correct installation of the stud. 5.2 Stud preparation For installation in every material coat the threads with oil. 5.3

31、Stud seating If the hole in the casing is preserrated, install a 0,05 mm thickness shim to prevent the premature interlocking (engagement) of the locking ring in the spotfacing serration. Screw the stud into the tapped hole by hand until the upper face of the locking ring abuts the stud serration en

32、d and the ring lower face comes into contact with the shim or the casing as shown on Figure 3 (there is no wrench for installing the studs). Remove the shim, align the ring external serration with the spotfacing ones in screwing the stud. EN 4460:20057 Key 1 Ring stop 2 Shim Figure 3 With the approp

33、riate tool, exert a continuous axial thrust on the locking ring until its total penetration into the casing as shown in Figures 4, 5 and 6. Dimensions in millimetres Figure 4 Figure 5 EN 4460:20058 Dimensions in millimetres Key 1 Spotfacing Figure 6 6 Stud removal and replacement 6.1 Removal The stu

34、d cannot be removed without destroying the locking ring (see Figure 7 and Table 3): a) cut the stud about 2 mm above the casing face; b) centre the drill on stud axis; c) drill the stud (to install the extractor); d) drill the stud in accordance with the following dimensions: Table 3 Dimensions in m

35、illimetres Drilling Pilot hole Finishing Nut end thread nominal diameter Diameter Depth min. Diameter Depth 0,4 5 1,6 6,1 2,4 6 2,2 6,0 7,1 2,8 After drilling, stud and ring are no longer mated. e) remove all portions of the ring remaining in the casing using a sharp-pointed tool; f) unscrew the stu

36、d using an extractor; g) clean the stud hole. EN 4460:20059 a) Cutting b) Pilot hole c) Drilling d) Drilling e) Removal f) Removal aSee Table 3. bThe drill diameter and drilling depth depend on extractor used. Figure 7 6.2 Replacement There are no oversized parts for repair. The replacement conditio

37、ns for studs with locking rings shall be defined by a repair instruction drawn up by the Manufacturing Design Office (MDO). EN 4460:2005BS EN BSI389 Chiswick High RoadLondonW4 4AL4460:2005BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standard

38、s. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant ai

39、m of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44

40、(0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Cu

41、stomer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as Britis

42、h Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give detail

43、s on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of thes

44、e and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website

45、 at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval

46、system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.