BS EN 4640-001-2009 Aerospace series - Connectors optical rectangular rack and panel multicontact 1 25 diameter ferrule with removable alignment sleeve holder - Technical specifica.pdf

1、BS EN4640-001:2009ICS 49.060NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Connectors, optical,rectangular, rack andpanel, multicontact,1,25 diameter ferrule,with removablealignment sleeveholderPart 001: Technical specificationThis British Stan

2、dardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 May 2009 BSI 2009ISBN 978 0 580 62416 2Amendments/corrigenda issued since publicationDate CommentsBS EN 4640-001:2009National forewordThis British Standard is the UK implementation of EN 4640-001:2009.The UK part

3、icipation in its preparation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic electrical and fibre optictechnology.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof

4、a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 4640-001:2009EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 4640-001February 2009ICS 49.060English VersionAerospace series - Connectors, optical, rec

5、tangular, rack andpanel, multicontact, 1,25 diameter ferrule, with removablealignment sleeve holder - Part 001: Technical specificationSrie arospatiale - Connecteurs, optiques, rectangulaires, contacts multiples, rackables, frule diamtre 1,25,quips dun porte sleeve dmontable - Partie 001:Spcificatio

6、n techniqueLuft- und Raumfahrt - Optischer Rechtecksteckverbinder,Gehuse, Einschub, Steckverbinder, Multipin,Ferrulendurchmesser 1,25 mm, demontierbarerZentrierhlsenhalter - Teil 001: TechnischeLieferbedingungenThis European Standard was approved by CEN on 11 July 2008.CEN members are bound to compl

7、y with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management

8、 Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theoffic

9、ial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Sloven

10、ia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national

11、 Members.Ref. No. EN 4640-001:2009: EBS EN 4640-001:2009EN 4640-001:2009 (E) 2 Contents Page Foreword 3Introduction .41 Scope 42 Normative references 43 Terms and definitions .54 Description .55 Design .66 Definition drawings67 Tests . 168 Quality assurance . 199 Designation and marking . 23BS EN 46

12、40-001:2009EN 4640-001:2009 (E) 3 Foreword This document (EN 4640-001:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received

13、 the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2009,

14、and conflicting national standards shall be withdrawn at the latest by August 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. Ac

15、cording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, La

16、tvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 4640-001:2009EN 4640-001:2009 (E) 4 Introduction This family of fibre optic connectors is derived from ARINC Specification 600 connectors.

17、It is suitable for use on aerospace onboard applications. It provides easy access for optical contact end face cleaning. The optical contacts are capable of accepting single cable sizes up to a maximum of 2 mm outside diameter. 1 Scope This standard specifies the general characteristics, the conditi

18、ons for qualification, acceptance and quality assurance, as well as the test programs and groups for rectangular multipin fibre optic connectors. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition c

19、ited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100*, Aerospace series Elements of electrical and optical connection Test methods Part 100: General EN 3197, Aerospace series Installation of aircraft electrical and optica

20、l interconnection systems 1EN 3909, Aerospace series Test fluids and test methods for electric components and sub-assemblies EN 4639-101, Aerospace series Connectors, optical, rectangular, modular, multicontact, 1,25 mm diameter ferrule, with removable alignment sleeve holder Part 101: Optical conta

21、ct for cable EN 4641-100 Operating temperatures between 65 C and 125 C Product standard EN 4640-002, Aerospace series Connectors, optical, rectangular, rack and panel, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder Part 002: Specification of performance and contact arran

22、gements EN 4640-003, Aerospace series Connectors, optical, rectangular, rack and panel, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder Part 003: Plug optical connector Product standard EN 4640-004, Aerospace series Connectors, optical, rectangular, rack and panel, multic

23、ontact, 1,25 diameter ferrule, with removable alignment sleeve holder Part 004: Receptacle optical connector Product standard EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard parts ARINC Specification 600, Air Transport Avionics Equipment Interfaces

24、 2MIL-I-81969/14, Installing and removal tools, connector electrical contact, type III, class 2, composition B 3*And all parts quoted in this standard. 1 Published as ASD Prestandard at the date of publication of this standard. 2 Published by: AERONAUTICAL RADIO, INC. 2551 Riva road, Annapolis, Mary

25、land 21401-7435 USA. 3 Published by: Department of Defence (DOD), the Pentagon, Washington, D.C. 20301 USA. BS EN 4640-001:2009EN 4640-001:2009 (E) 5 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 2591-100 apply. 4 Description 4.1 General This docume

26、nt describes an optical connector insert to be installed in plug and receptacle housings. Plug and receptacle housings conform to ARINC Specification 600. The precise alignment of the optical contacts is accomplished by alignment sleeves held in a removable sleeve holder. The plug connector contain

27、male insert as specified in EN 4640-003. The receptacles connector contain female insert as specified in EN 4640-004. The female insert is composed of an insert and a removable sleeve holder as specified in EN 4640-004. The sleeve holder is delivered with the female insert. It is considered as a par

28、t of the female insert (specific design per manufacturer). The sleeve holder can be supplied separately only for repair purpose. The optical contact is in accordance with EN 4639-101. The connectors are keyed as specified in ARINC Specification 600. Connector type designation as specified in ARINC S

29、pecification 600. 4.2 Receptacle Receptacle description as specified in ARINC Specification 600. 4.3 Plug Plug description as specified in ARINC Specification 600. 4.4 Materials and surface treatment 4.4.1 General When dissimilar metals are in close contact, adequate protection against corrosion sha

30、ll be used for the electromotive force of the cell not to exceed 0,25 V (see EN 3197). 4.4.2 Housings The connector housing description as specified in ARINC Specification 600. BS EN 4640-001:2009EN 4640-001:2009 (E) 6 4.4.3 Optical contacts and alignment sleeves The contacts shall be of suitable ma

31、terials as specified in EN 4639-101. The optical alignment sleeves shall be of suitable materials as specified in EN 4640-002. The optical contacts are sprung-loaded. The spring force is defined in the product standard (EN 4639-101). 4.4.4 Metallic or non-metallic materials The materials used for in

32、serts, seals and grommets shall have a hardness and mechanical characteristics consistent with the required use. 5 Design 5.1 Housing The connector housing design as specified in ARINC Specification 600. 5.2 Connector inserts The connector insert carrying the optical contacts shall be in hard materi

33、al and have a cross section and radii such that no cracks, flaking or breaks can occur in normal operation. The mechanical contacts retention system shall be integrated in the connector insert. Sealing of the rear face of the connector insert can be provided by a grommet adapted to the external diam

34、eter of the cable. The design shall permit individual installation of the contacts without removal of the connector insert. Fitting and removal of the contacts shall be from the rear. For ease of operation, tools as per MIL-I-81969/14-03 (P/N for size 16) may be used. Contact position identification

35、 shall be permanent and contrasted on the rear face of the insert or grommet. 6 Definition drawings 6.1 General The general dimensions and the masses of receptacles, plugs and protective covers are given in the product standards. 6.2 Receptacle All housing dimensions are defined in ARINC Specificati

36、on 600. 6.3 Plug All housing dimensions are defined in ARINC Specification 600. BS EN 4640-001:2009EN 4640-001:2009 (E) 7 6.4 Connector inserts 6.4.1 Connector interface insert See Figure 1. Key 1 Receptacle connector 5 Mechanical bottom of receptacle 2 Mechanical bottom of plug 6 Plug connector 3 F

37、ront face of the insert 7 Pin cavity position A 4 Sleeve holder Figure 1 6.5 Mating dimensions The mating dimensions receptacle (free position) are shown in Figure 2. BS EN 4640-001:2009EN 4640-001:2009 (E) 8 Sleeve-holder screw cavity (Sleeve-holder not show) Optical contact position Key 1 Limit st

38、op of the alignment sleeve holder screw 2 (unmated position) 3 Mechanical bottom of the receptacle NOTE Other dimensions in accordance with ARINC Specification 600. Figure 2 BS EN 4640-001:2009EN 4640-001:2009 (E) 9 The mating dimensions of plug (free position) are shown in Figure 3. Key 1 (unmated

39、position) 2 Mechanical bottom of the plug NOTE Other dimensions in accordance with ARINC Specification 600. Figure 3 6.5.1 Receptacle with female insert and plug with male insert The displacement of the optical contact in the connector is shown in Figure 4. Dimensions and tolerances are in millimetr

40、es. Mating position Key 1 Mechanical bottom 2 Receptacle connector 3 Plug connector Figure 4 1 2 min.7,01 5,92 1 2 3 BS EN 4640-001:2009EN 4640-001:2009 (E) 10 6.5.2 Receptacle connector Contact entering mating sleeve holder Contact optically mated Key 1 # 22 Electrical contact 6 Bloc side 2 Sleeve

41、holder 7 Rack side 3 # 12 Electrical contact 8 Plug 4 # 16 Electrical contact 9 Optical contact 5 Receptacle X1 contact entering mating sleeve holder X2 contact optically mated Optical contact 18,68 mm .735 16,53 mm .650 # 22 16,30 mm .642 b13,89 mm .547 # 22 20,32 mm .800 a18,99 mm .748 Optical con

42、tact 16,25 mm .634 13,28 mm .523 # 20 20,54 mm .809 a18,82 mm .741 # 20 16,48 mm .649 b14,04 mm .553 # 16 25,70 mm 1.012 a24,10 mm .949 # 16 18,42 mm .725 b20,77 mm .818 # 12 25,60 mm 1.008 a24,20 mm .953 # 12 19,60 mm .772 b17,57 mm .692 aValues for # 22, # 20, # 16, # 12 electrical contacts are fo

43、r contact entering mating insulator extracted from ARINC Specification 600. These values are given for information only. Refer to ARINC Specification 600 for more information. bValues for # 22, # 20, # 16, # 12 electrical contacts are for contact electrically engaged extracted from ARINC Specificati

44、on 600. These values are given for information only. Refer to ARINC Specification 600 for more information. Figure 5 1 1 2 2 3 3 4 4 5 5 6 7 768 9 89BS EN 4640-001:2009EN 4640-001:2009 (E) 11 6.5.3 Coupling contact condition Key 1 D2 - Sleeve cavity inner diameter 2 Sleeve to sleeve-holder cavity st

45、op 3 Optical contact to sleeve-holder stop Condition: in every case, J 0 The different shapes and dimensions of the sleeve cavity must be defined to warranty this condition. Figure 6 6.5.4 Contact arrangements Identification of the contact position shall be permanently marked in contrasting colour o

46、n the rear face of the module. Contact arrangements 20F12Q8 for shell size 2 or 3: see Figure 7. BS EN 4640-001:2009EN 4640-001:2009 (E) 12 Receptacle rear face Plug rear face Plug front face Key 1 Ref on ribs 2 Sleeve-holder screw hole (on receptacle side) 3 12 optical cavities 4 End of the optical

47、 contacts 5 Keyway 6 8 cavities for # 8 quadrax contacts Contact body is grounded to the connector shell 7 Angular position of the optical contact polarization key 8 Step Number of contacts Contact size Insert cavity location 12 Optical contact RR/RR 1 thru 12 8 8 (Quadrax) FR/FR (Receptacle side) R

48、R/RR (Plug side) AA thru HH NOTE RR/RR = Contacts are REAR RELEASE / REAR REMOVABLE FR/FR = Contacts are FRONT RELEASE / FRONT REMOVABLE Figure 7 Receptacle front face (without sleeve holder)BS EN 4640-001:2009EN 4640-001:2009 (E) 13 Contact arrangements 36F36 for shell size 2 or 3: see Figure 8. Re

49、ceptacle rear face Plug rear face Plug front face Key 1 Ref on ribs 2 3 cavities for sleeve-holder screw (on receptacle side) 3 Keyway 4 36 optical cavities 5 End of the optical contacts 6 Angular position of the optical contact polarization key Number of contacts Contact size Insert cavity location 36 Optical contact RR/RR 1 thru 36 NOTE RR/RR = Contacts are REAR RELEASE / REAR REMOVABLE FR/FR = Contacts are FRONT RELEASE / FRONT