BS EN 485-4-1994 Aluminium and aluminium alloys - Sheet strip and plate - Tolerances on shape and dimensions for cold-rolled products《铝和铝合金 薄板材、带材和板材 冷轧制品的形状和尺寸公差》.pdf

1、BRITISH STANDARD BS EN 485-4:1994 Aluminium and aluminium alloys Sheet, strip and plate Part 4: Tolerances on shape and dimensions for cold-rolled products The European Standard EN 485-4:1993 has the status of a British Standard UDC 669.71-41-122.2:669.715.018.26BSEN 485-4:1994 This British Standard

2、, having been prepared under the direction of the Non-ferrous Metals Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 January 1994 BSI 12-1998 The following BSI references relate to the work on this standard: Committee reference NFM/35

3、Draft for comment91/40616 DC ISBN 0 580 21703 5 Cooperating organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Oesterreichisches Normungsinstit

4、ut Belgium Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland

5、Ireland National Standards Authority of Ireland Italy Ente Nazionale Italiano di Unificazione Luxembourg Inspection du Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Asociacin Espaola de Normaliz

6、acin y Certificacin Sweden Standardiseringskommissionen i Sverige Switzerland Association suisse de normalisation United Kingdom British Standards Institution Amendments issued since publication Amd. No. Date CommentsBSEN 485-4:1994 BSI 12-1998 i Contents Page Cooperating organizations Inside front

7、cover National foreword ii Foreword 2 Text of EN 485-4 3 National annex NA (informative) Committees responsible Inside back cover National annex NB (informative) Cross-references Inside back coverBSEN 485-4:1994 ii BSI 12-1998 National foreword This Part of BS EN 485 has been prepared under the dire

8、ction of the Non-ferrous Metals Standards Policy Committee and is the English language version of EN485-4:1993 Aluminium and aluminium alloys Sheet, strip and plate Part 4 Tolerances on shape and dimensions for cold-rolled products. This Part of BS EN 485, together with BS EN 485-1:1994 Aluminium an

9、d aluminium alloys Sheet, strip and plate Part 1 Technical conditions for inspection and delivery and BS EN 485-3:1994 Aluminium and aluminium alloys Sheet, strip and plate Part 3 Tolerances on shape and dimensions for hot-rolled products will supersede parts of BS 1470:1987 Specification for wrough

10、t aluminium and aluminium alloys for general engineering purposes: plate, sheet and strip. However, BS 1470:1987 will not be withdrawn until the remaining standards which replace it are published. These are as follows: BS EN 485-2, Aluminium and aluminium alloys Sheet, strip and plate Part2: Mechani

11、cal properties. BS EN 515, Aluminium and aluminium alloys Wrought products Temper designations. BS EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical composition. BS EN 573-4, Aluminium and aluminium alloys Chemical composition and form of wro

12、ught products Part 4: Forms of products. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.

13、Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 12, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment

14、 table on theinside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 485-4 October 1993 UDC 669.71-41-122.2:669.715.018.26 Descriptors: Iron and steel products, cold-rolled products, rolled products, metal plates, steel strips, aluminium, aluminium alloys, dimensional tolerances, for

15、m tolerances English version Aluminium and aluminium alloys Sheet, strip and plate Part4: Tolerances on shape and dimensions for cold-rolled products Aluminium et alliages daluminium Tles, bandes et tles paisses Partie 4: Tolrances sur forme et dimensions des produits lamins froid Aluminium und Alum

16、iniumlegierungen Bnder, Bleche und Platten Teil 4: Grenzabmae und Formtoleranzen fr kaltgewalzte Erzeugnisse This European Standard was approved by CEN on1993-10-08. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Stan

17、dard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official versions (English, French,

18、German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, Franc

19、e, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 199

20、3 Copyright reserved to CEN members Ref. No. EN 485-4:1993 EEN485-4:1993 BSI 12-1998 2 Foreword This European Standard has been drawn up by CEN/TC 132 “Aluminium and aluminium alloys”, whose Secretariat is held by the Association Franaise de Normalisation (AFNOR). Within its programme of work, Techn

21、ical Committee CEN/TC 132 entrusted CEN/TC 132/WG 7 “Sheet, strip and plate” to work out the following standard: EN 485-4, “Aluminium and aluminium alloys Sheet, strip and plate Part 4: Tolerances on dimensions and form for cold-rolled products”. This standard is part of a set of four standards. The

22、 other standards deal with: EN 485-1, “Aluminium and aluminium alloys Sheet, strip and plate Part 1: Technical conditions for inspection and delivery”. EN 485-2, “Aluminium and aluminium alloys Sheet, strip and plate Part2:Mechanical properties”. EN 485-3, “Aluminium and aluminium alloys Sheet, stri

23、p and plate Part3: Tolerances on dimensions and form for hot-rolled products”. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 1994, and conflicting national standards shall be withdrawn at

24、the latest by April 1994. The Standard was approved and in accordance with the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norwa

25、y, Portugal, Spain, Sweden, Switzerland, United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Dimensional tolerances 3 3.1 Thickness 3 3.2 Width 5 3.3 Length 5 4 Shape tolerances 6 4.1 Lateral curvature 6 4.2 Flatness 6 4.3 Squareness 6 Annex A (normative) Alloy split into G

26、roup I and Group II 11 Annex B (normative) Other thickness tolerances 11 Figure 1 Lateral curvature of plate or sheet of length L 6 Figure 2 Transverse arch 7 Figure 3 Longitudinal arch 8 Figure 4 Buckles 8 Figure 5 Edge waves 9 Figure 6 Measurement of squareness 10 Table 1 Thickness tolerances 4 Ta

27、ble 2 Width tolerances for strip 5 Table 3 Width tolerances for sheet and plate 5 Table 4 Length tolerances for sheet and plate 5 Table 5 Lateral curvature tolerances for strip 6 Table 6 Lateral curvature tolerances for sheet and plate 7 Table 7 Flatness tolerances for sheet and plate 7 Table 8 Squa

28、reness tolerances for sheet and plate 9 Table A1 Alloy Groups 11EN485-4:1993 BSI 12-1998 3 1 Scope This Part of EN 485 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy sheet, strip and plate obtained by cold-rolling, for general engineering applications. It

29、applies to products with a thickness over 0,20 mm up to and including 50 mm. It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (rerollstock) or to special products such as corrugated, embossed, etc. sheet and strip or to special applications such as

30、 aerospace, can stock, etc. which are dealt with in separate European Standards. Technical conditions for inspection and delivery of products covered by this standard are specified inEN485-1. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from ot

31、her publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment o

32、r revision. For undated references the latest edition of the publication referred to applies. EN 485-1, Aluminium and aluminium alloys Sheet, strip and plate Part 1: Technical conditions for inspection and delivery. EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought pr

33、oducts Part 3: Chemical composition. 3 Dimensional tolerances 3.1 Thickness 3.1.1 For the purpose of this European Standard the alloys are distributed into two groups which correspond to varying difficulty when manufacturing the products. Tighter thickness tolerances apply to Group I alloys (soft al

34、loys). The grouping is carried out according to the specified chemical composition limits of the alloys (see EN 573-3) as follows: Group I alloys: 1000 series alloys; non heat-treatable7000 and8000 series alloys; 4000 series alloys with less than2% maximum specified silicon content; 3000 and 5000 se

35、ries alloys for which the maximum specified magnesium and manganese contents are each no greater than1,8% and their sum no greater than2,3%. Group II alloys: all alloys which do not belong to Group I. The split into Group I and Group II of the most commonly used general engineering alloys is given i

36、n annex A (see Table A1). 3.1.2 Thickness tolerances for sheet, strip and plate are specified in Table 1. 3.1.3 Other thickness tolerances may be agreed between supplier and purchaser. They are specified in annex B.EN485-4:1993 4 BSI 12-1998 Table 1 Thickness tolerances Dimensions in millimetres Spe

37、cified thickness Thickness tolerance for specified width Up to and including 1000 Over1000 up to and including 1250 Over 1250 up to and including 1600 Over1600 up to and including 2000 Over2000 up to and including 2500 Over2500 up to and including 3000 Over3000 up to and including 3500 Over Up to an

38、d including Alloy Group Alloy Group Alloy Group Alloy Group Alloy Group Alloy Group Alloy Group I II I II I II I II I and II I and II I and II 0,20 0,4 0,02 0,03 0,04 0,05 0,05 0,06 0,4 0,5 0,03 0,03 0,04 0,05 0,05 0,06 0,06 0,07 0,10 0,5 0,6 0,03 0,04 0,05 0,06 0,06 0,07 0,07 0,08 0,11 0,6 0,8 0,03

39、 0,04 0,06 0,07 0,07 0,08 0,08 0,09 0,12 0,8 1,0 0,04 0,05 0,06 0,08 0,08 0,09 0,09 0,10 0,13 1,0 1,2 0,04 0,05 0,07 0,09 0,09 0,10 0,10 0,12 0,14 1,2 1,5 0,05 0,07 0,09 0,11 0,10 0,12 0,11 0,14 0,16 1,5 1,8 0,06 0,08 0,10 0,12 0,11 0,13 0,12 0,15 0,17 1,8 2 0,06 0,09 0,11 0,13 0,12 0,14 0,14 0,16 0

40、,19 2 2,5 0,07 0,10 0,12 0,14 0,13 0,15 0,15 0,17 0,20 2,5 3,0 0,08 0,11 0,13 0,15 0,15 0,17 0,17 0,19 0,23 3,0 3,5 0,10 0,12 0,15 0,17 0,17 0,19 0,18 0,20 0,24 3,5 4,0 0,15 0,20 0,22 0,23 0,25 0,34 0,38 4,0 5,0 0,18 0,22 0,24 0,25 0,29 0,36 0,42 5,0 6,0 0,20 0,24 0,25 0,26 0,32 0,40 0,46 6,0 8,0 0,

41、24 0,30 0,31 0,32 0,38 0,44 0,50 8,0 10 0,27 0,33 0,36 0,38 0,44 0,50 0,56 10 12 0,32 0,38 0,40 0,41 0,47 0,53 0,59 12 15 0,36 0,42 0,43 0,45 0,51 0,57 0,63 15 20 0,38 0,44 0,46 0,48 0,54 0,60 0,66 20 25 0,40 0,46 0,48 0,50 0,56 0,62 0,68 25 30 0,45 0,50 0,53 0,55 0,60 0,65 0,70 30 40 0,50 0,55 0,58

42、 0,60 0,65 0,70 0,75 40 50 0,55 0,60 0,63 0,65 0,70 0,75 0,80 When measuring the thickness, a zone10mm wide from the edges of the product shall be disregarded.EN485-4:1993 BSI 12-1998 5 3.2 Width 3.2.1 Width tolerances for strip are specified inTable 2. 3.2.2 Width tolerances for sheet and plate are

43、 specified inTable 3. 3.3 Length 3.3.1 Length tolerances for strip are not specified. 3.3.2 Length tolerances for sheet and plate are specified inTable 4. Table 2 Width tolerances for strip Table 3 Width tolerances for sheet and plate Table 4 Length tolerances for sheet and plate Dimensions in milli

44、metres Specified thickness Width tolerance for specified width Over Up to and including Up to and including100 Over100 up to and including300 Over300 up to and including500 Over500 up to and including1250 Over1250 up to and including1650 Over1650 up to and including2600 0,20 0,6 0,6 1,0 1,0 2,0 2,0

45、3,0 3,0 5,0 Dimensions in millimetres Specified thickness Width tolerance for specified width Over Up to and including Up to and including500 Over500 up to and including1250 Over1250 up to and including2000 Over2000 up to and including3000 Over3000 up to and including3500 0,20 3,0 3,0 6,0 6,0 50 Dim

46、ensions in millimetres Specified thickness Length tolerance for specified length Over Up to and including Up to and including1000 Over1000 up to and including2000 Over2000 up to and including3000 Over3000 up to and including5000 Over5000 0,20 3,0 +0,2% of specified length 3,0 6,0 6,0 50 + 0,3 0 + 0,

47、4 0 + 0,6 0 + 1,5 0 + 2,5 0 + 3 0 + 0,3 0 + 0,5 0 + 1 0 + 1,5 0 + 2,5 0 + 3 0 + 0,4 0 + 0,7 0 + 1,2 0 + 2 0 + 2,5 0 + 3 0 + 1 0 + 1 0 + 1,5 0 + 2 0 + 2,5 0 + 4 0 + 1,5 0 + 2 0 + 3 0 + 3 0 + 5 0 + 1,5 0 + 3 0 + 4 0 + 5 0 + 3 0 + 4 0 + 5 0 + 8 0 + 8 0 + 4 0 + 5 0 + 5 0 + 8 0 + 8 0 + 3 0 + 4 0 + 6 0 +

48、8 0 + 4 0 + 6 0 + 8 010 + 0 + 6 0 + 8 010 + 010 + 0EN485-4:1993 6 BSI 12-1998 4 Shape tolerances 4.1 Lateral curvature 4.1.1 Lateral curvature tolerances for strip with width up to and including3500mm are specified inTable 5. Table 5 Lateral curvature tolerances for strip (measured on2000mm strip leng