1、BSI Standards PublicationBS EN 6059-601:2014Aerospace series Electricalcables, installation Protection sleeves TestmethodsPart 601: Open and closeBS EN 6059-601:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 6059-601:2014.The UK participation in its prepar
2、ation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic electrical and fibre optictechnology.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are r
3、esponsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 84536 9ICS 49.060Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards
4、 Policy and Strategy Committee on 31 May 2014.Amendments issued since publicationDate Text affectedBS EN 6059-601:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6059-601 April 2014 ICS 49.060 English Version Aerospace series - Electrical cables, installation - Protection sleeves - Test met
5、hods - Part 601: Open and close Srie arospatiale - Cbles lectriques, installation - Gaines de protection - Mthodes dessais - Partie 601: Ouverture et fermeture Luft- und Raumfahrt - Elektrische Leitungen, Installation - Schutzschluche - Prfverfahren - Teil 601: ffnen und Schlieen This European Stand
6、ard was approved by CEN on 4 January 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning s
7、uch national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its o
8、wn language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
9、 Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NOR
10、MUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 6059-601:2014 EBS EN 6059-601:2014EN 6059-601:2014 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative refe
11、rences 4 3 Preparation of specimens .4 4 Method 5 5 Requirements .6 BS EN 6059-601:2014EN 6059-601:2014 (E) 3 Foreword This document (EN 6059-601:2014) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out
12、in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by public
13、ation of an identical text or by endorsement, at the latest by October 2014, and conflicting national standards shall be withdrawn at the latest by October 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC s
14、hall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, D
15、enmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 6059-
16、601:2014EN 6059-601:2014 (E) 4 1 Scope This European Standard specifies a method of assessing the behaviour of protection sleeves or conduits subject to open and close manipulation for installation, rework and repairs. It shall be used together with EN 6059-100. 2 Normative references The following
17、documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 6059-100, Aerospac
18、e series - Electrical cables, installation - Protection sleeves - Test methods - Part 100: General 3 Preparation of specimens Each specimen having 1,0 m length shall be placed horizontally on a table. A harness made of standard aerospace wires, having 1,2 m length, with a diameter defined as the max
19、imum diameter applicable on the specimen size. The test shall be carried out at ambient temperature Ta(typically 20 C). Dimensions in millimetres Key 1 Wire bundle 2 Sleeve 3 Bundle at the maximum allowed diameter of the sleeve Figure 1 Specimen configuration BS EN 6059-601:2014EN 6059-601:2014 (E)
20、5 4 Method The purpose of this test shall be to check that there is no damage, no loss of memory form performance, no wires or filaments broken on the sleeve specimen. The test shall be performed on the smallest size and a medium size as defined in the concerned specification or product standard. Us
21、ing the installation tool defined by the manufacturer, the wire bundle will be installed X time (X defined in the product standard) inside the sleeve, and removed from the sleeve. Phase 1: Insert tooling inside the sleeve, see Figure 2. Figure 2 Phase 2: Install the sleeve on the wire bundle with th
22、e tooling, see Figure 3. Figure 3 Phase 3: Remove the tooling from the extremity of the sleeve, see Figure 4. BS EN 6059-601:2014EN 6059-601:2014 (E) 6 Figure 4 Phase 4: Remove the sleeve from the wire bundle by pulling the sleeve, see Figure 5. Figure 5 5 Requirements Visual control of the specimen
23、 after installation and dismantling cycles: No visible damage, broken wires or broken filaments; No degradation of the inside layer, in case of protective inside layer such as PTFE tape; The maximum diameter tracer indicator, must be not visible, to confirm the correct function of the memory form of
24、 the specimen. This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Stan
25、dards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embo
26、died in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your org
27、anization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, th
28、rough our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standar
29、ds easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date.
30、 You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive
31、 the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few
32、or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our produc
33、ts and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and
34、 copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no
35、extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1