BS EN 6076-2017 Aerospace series Static seal elements O-Ring for straight thread tube fitting boss ethylene-propylene moulded phosphate ester resistant (-55 C to 107 C) - Inch seri.pdf

1、Aerospace series - Static seal elements O-Ring for straight thread tube fitting boss, ethylene-propylene, moulded, phosphate ester resistant (-55 C to 107 C) - Inch seriesBS EN 6076:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEANSTANDARDNORME EUROPENNE E

2、UROPISCHE NORMEN 6076 May 2017ICS 49.035English VersionAerospace series - Static seal elements O-Ring for straight thread tube fitting boss, ethylene-propylene, moulded, phosphate ester resistant (-55 C to 107 C) - Inch series Srie arospatiale - Joint torique statique pour raccord embout mle paul, t

3、hylne-propylne, moul, rsistant lester phosphorique (-55 C 107 C) -Srie en inchesLuft- und Raumfahrt - Statische Dichtungen O-Ring, frgerade Einschraubstutzen mit Bund, Ethylen-Propylen,geformt, bestndig gegen Phosphorsureester (-55 Cbis 107 C) - InchReiheThis European Standard was approved by CEN on

4、 4 December 2016.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving thisEuropean Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical referencesconcerning such national standards may be

5、 obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made bytranslation under the responsibility of a CEN member into its own language and notified to th

6、e CEN-CENELEC ManagementCentre has the same status as the officialversions.CEN members are the nationalstandards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland

7、, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Ce

8、ntre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reservedworldwide for CENnational Members.Ref. No. EN 6076:2017 ENational forewordThis British Standard is the UK implementation of EN 6076:2017.The UK participation in its preparation was entrus

9、ted to Technical Committee ACE/69, Aerospace hydraulic systems, fluids and components.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for i

10、ts correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 95515 0ICS 49.035Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and

11、Strategy Committee on 31 July 2017.Amendments/corrigenda issued since publicationDate Text affected BRITISH STANDARDBS EN 6076:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6076 May 2017 ICS 49.035 English Version Aerospace series - Static seal elements O-Ring for straight thread tube fit

12、ting boss, ethylene-propylene, moulded, phosphate ester resistant (-55 C to 107 C) - Inch series Srie arospatiale - Joint torique statique pour raccord embout mle paul, thylne-propylne, moul, rsistant lester phosphorique (-55 C 107 C) - Srie en inches Luft- und Raumfahrt - Statische Dichtungen O-Rin

13、g, fr gerade Einschraubstutzen mit Bund, Ethylen-Propylen, geformt, bestndig gegen Phosphorsureester (-55 C bis 107 C) - Inch Reihe This European Standard was approved by CEN on 4 December 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions

14、for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in th

15、ree official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards b

16、odies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, S

17、lovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reser

18、ved worldwide for CEN national Members. Ref. No. EN 6076:2017 EBS EN 6076:2017EN 6076:2017 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Requirements 4 4 Designation . 6 5 Marking and packaging 6 6 Technical specification . 6 7 Quality assurance . 6 (informative)

19、 Standard evolution form 7 BS EN 6076:2017EN 6076:2017 (E) 3 European foreword This document (EN 6076:2017) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Associa

20、tion, this European Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by en

21、dorsement, at the latest by November 2017, and conflicting national standards shall be withdrawn at the latest by November 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any

22、 or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republ

23、ic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 6076:2017EN 6076:2017 (E) 4 1 Scope This Euro

24、pean Standard specifies the characteristics of configuration, dimensions, tolerances and mass for moulded O-Ring seal elements, phosphate ester fluid resistant, for straight thread tube fitting boss for use as static seals in hydraulic systems for aerospace application. Application temperature range

25、: 55 C to 107 C of continuous operation. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the

26、 referenced document (including any amendments) applies. EN 6109, Aerospace series Static seal elements elastomer moulded, phosphate ester resistant Technical specification1)EN 6111, Aerospace series Ethylene-propylene elastomer (EPM/EPDM) Hardness 80 IRHD for static seal elements in hydraulic syste

27、ms for long-term application Material standard1)EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard parts 3 Requirements 3.1 Configuration, dimensions, tolerances and mass Configuration shall be in accordance with Figure 1; Dimensions shall conform wit

28、h Figure 1 and Table 1; Tolerances shall be in accordance with Table 1; Mass shall be in accordance with Table 1. Dimensions and tolerances are expressed in millimetres (inches). 1)Published as ASD-STAN Prestandard at the date of publication of this European Standard. http:/www.asd-stan.org/ BS EN 6

29、076:2017EN 6076:2017 (E) 5 3.2 Material Ethylene-propylene elastomer (EPM/EPDM) per EN 6111. Figure 1 Configuration Table 1 O-Rings Diameter code, dimensions, tolerances and mass Diameter codeanullW nullID Mass kg/1000 pieces Tolerances Tolerances null10 % 02 1,63 (.064) null0,08 (null.003) 6,07 (.2

30、39) null0,13 (null.005) 0,059 03 7,65 (.301) 0,072 04 1,83 (.072) 8,92 (.351) 0,105 05 10,52 (.414) 0,120 06 1,98 (.078) 11,89 (.468) 0,158 08 2,21 (.087) 16,36 (.644) 0,263 10 2,46 (.097) 19,18 (.755) 0,380 12 2,95 (.116) null0,10 (null.004) 23,47 (.924) null0,15 (null.006) 0,668 16 29,74 (1.171) 0

31、,826 20 3,00 (.118) 37,47 (1.475) null0,25 (null.010) 1,058 24 43,69 (1.720) 1,221 28 53,09 (2.090) 1,466 32 59,36 (2.337) 1,630 aThe diameter code corresponds to the tube outer diameter (ref.) in 1/16 inch. BS EN 6076:2017EN 6076:2017 (E) 6 4 Designation EXAMPLE NOTE If necessary, the code I9005 sh

32、all be placed between the description block and the identity block. 5 Marking and packaging 5.1 Marking of parts Each O-Ring shall be marked with two (2) white stripes. 5.2 Packaging All O-Rings shall be individually packaged in suitable and light protected bags. They shall be thoroughly clean befor

33、e packaging. Packaging shall be accomplished under conditions which will assure freedom from all contamination or damage to the O-Rings. The unit packaging shall be of such material and construction as to protect the O-Ring from contamination until the package is opened. Each package shall contain t

34、he following identification in print of a size that can be easily recognized: Phosphate ester resistant; O-Ring; Standard number of O-Ring (e. g. EN 6076-08); Manufacturers part number (if any) and address or trademark; Cure date (quarter and year); Legend “ETHYLENE PROPYLENE” and “DO NOT FOLD”. 6 T

35、echnical specification See EN 6109. 7 Quality assurance See EN 9133. BS EN 6076:2017EN 6076:2017 (E) 7 (informative) Standard evolution form The main changes with respect to the previous edition are listed in Table A.1. Table A.1 Main changes to previous edition prEN/EN Number Edition Publication Da

36、te Modification Reason and validation prEN 6076 P1 12/2004 Scope updated, add “static seals” as mentioned in the title. Clarification. Clause 7 “Quality assurance” added. Reference to EN 9133 required according to ASD-STAN regulations (GPM). Editorial updated. According to ASD-STAN requirements. BS

37、EN 6076:2017This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization prod

38、ucts are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been

39、carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Fin

40、d out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where har

41、d copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of

42、 and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or dissemina

43、te any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British S

44、tandard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be p

45、rinted for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document

46、.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing te

47、am.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from y

48、our desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an

49、updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can